Arrow Christa 1401 User manual

Christa
ASSEMBLY INSTRUCTIONS
ITEM NO.: 1401 White

Assembly InstructionsChrista 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Use and Care
Your cabinet normally requires a minimum amount of maintenance; however, it is worth noting the
following for regular cleaning:
To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT use
ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Phillips Screwdriver Hammer Electric Screwdriver
Torque set to 3-5

Assembly InstructionsChrista 3
Parts List: Panels
ITEM DESCRIPTION QTY. PACK.
YCenter Panel 1 3 of 3
ZRight Side Panel 1 3 of 3
VDrawer Support Gate Leg 1 3 of 3
OInsert Holder 1 3 of 3
A4 Side Leaf 1 3 of 3
O3 Side Gate Leg 1 3 of 3
LDrawer Front 1 2 of 3
L1 Drawer Left Side Panel 1 3 of 3
L2 Drawer Right Side Panel 1 3 of 3
L3 Drawer Back Panel 1 3 of 3
L4 Drawer Bottom Panel 1 3 of 3
Hardware Box 1 1 of 3
ITEM DESCRIPTION QTY. PACK
ATop Panel 1 1 of 3
A1 Quilt Leaf Panel 1 2 of 3
A3 In-Drawer Support Panel 1 3 of 3
O1 Left Gate Leg 1 2 of 3
02 Right Gate Leg 1 2 of 3
A2 Lift Panel (pre-installed) 1 2 of 3
GBottom Panel 1 2 of 3
D1 Top Back Panel 1 2 of 3
D2 Bottom Back Panel 1 2 of 3
XLeft Side Panel 1 3 of 3
O4 Drawer Gateleg Support Panel 1 3 of 3
A1
A
A2
X
O1
D1
Y
D2
O2
Z
O3
A4
O4
A3
V
O
G
L4
L1
L3
L2
L

Assembly InstructionsChrista 4
Parts List: Hardware
Plate Caster x5
t1
3.5x14 Screw x108
s1
6x35 Cam Bolt x51
c1
8x30 Dowel Pin x40
d1
5⁄8“ Cam Cover x51
c2
Hinge Body x2
g1
Caster x3
t2
6x25 Bolt and Nut x3
b
Alignment Pin x4
s4
Butt Hinge x12
h2
Magnet x4
m
Handle x1
h
4x20 Fix Bolt x2
b2
TIP: Keep all the parts in their individually labeled bags. This will make finding parts easier as you assemble your cabinet.
3x14 Screw x8
s2
Threaded Dowel Pin x3
p

Assembly InstructionsChrista 5
Manual Lift Parts
b1
b2
a
c
h1
c
a
b1
PART DESCRIPTION QT Y.
aBolt and Wing Nut 2
b1 Large Bracket 2
b2 Small Bracket 1
cChain 2
h1 Hexagonal Bolt 2
h1
NOTE: No Assembly Required

Assembly InstructionsChrista 6
Step 1: Cabinet Shell
G
G
Plate Caster x5
t1
3.5x14 Screw x20
s1
6x35 Cam Bolt x14
c1
Attach t1 Plate Casters to the underside of
Panel G using s1 Screws.
Lock the casters and flip Panel G over.
Attach c1 Cam Bolts to Panel G as shown.

Assembly InstructionsChrista 7
Step 1: Cabinet Shell
8x30 Dowel Pin x2
d1
G
O
O
Insert d1 Dowel Pins into the
bottom edge of Panel O.
5⁄8“ Cam Cover x2
c2
Attach Panel O to Panel G as shown, insert-
ing cam bolts into cam locks..
Tighten cam locks and apply c2 Cam Covers.

Assembly InstructionsChrista 8
8x30 Dowel Pin x18
d1
Step 1: Cabinet Shell
D1
D2
O4
Insert d1 Dowel Pins into the edges of
Panels D1 and D2 as shown.
Insert dowel pins into the edge of Panel
O4 as shown.

Assembly InstructionsChrista 9
Step 1: Cabinet Shell
6x35 Cam Bolt x7
c1
8x30 Dowel Pin x4
d1
O4
X
X
Back Edge
Back Edge
Attach c1 Cam Bolts and d1 Dowel
Pins to Panel X as shown.
Attach Panel O4 to Panel
X as shown , inserting cam
bolts into cam locks..
Tighten cam locks and apply
c2 Cam Covers.
5⁄8“ Cam Cover x3
c2

Assembly InstructionsChrista 10
Step 1: Cabinet Shell
Z
Y
6x35 Cam Bolt x4
c1
8x30 Dowel Pin x8
d1
Attach 4 c1 Cam Bolts to Panel Z.
Insert 4 d1 Dowel Pins into the edges
of Panel Z.
Attach 4 d1 Dowel Pins into the edges of
Panel Y.

Assembly InstructionsChrista 11
D2
D1
Z
X
Step 1: Cabinet Shell
Attach Panels D1 and D2 to Panels X and Z as
shown, making sure that dowel pins on Panel D1
point to the top of the cabinet and the dowel pins
on Panel D2 point to the bottom of cabinet.
Tighten cam locks and apply c2 Cam Covers.
5⁄8“ Cam Cover x8
c2
NOTE: The image below shows upside down construction of
Panels X, D1/D2 and Z. This will make attaching the bottom of
the cabinet easier in the next step.

Assembly InstructionsChrista 12
X
D1
D2
Z
G
Step 1: Cabinet Shell
Attach Panel G to Panels Z, D2, X and O4, inserting cam
bolts into cam locks.
Tighten cam locks and apply c2 Cam Covers.
Make sure the casters are locked and flip the
cabinet up onto its wheels.
You may need a friend to help you with this
step, but it is not required.
5⁄8“ Cam Cover x10
c2

Assembly InstructionsChrista 13
Step 1: Cabinet Shell
X
Z
Y
G
Gently lower Panel Y onto Panel G, inserting
cam bolts into cam locks.
Tighten cam locks and apply c2 Cam Covers.
5⁄8“ Cam Cover x2
c2

Assembly InstructionsChrista 14
Step 1: Cabinet Shell
6x35 Cam Bolt x10
c1
A
A
Y
Z
X
D1
Attach c1 Cam Bolts to the underside of
Panel A.
Gently lower Panel A onto Panels X, D1, Y and Z,
inserting cam bolts into cam locks.
Tighten cam locks and apply c2 Cam Covers.
5⁄8“ Cam Cover x10
c2

Assembly InstructionsChrista 15
Step 2: Gate Legs and Support Panels
Hinge Body x2
g1
Caster x1
t2
Alignment Pin x1
s4
View from inside cabinet
V
O4
V
O4
3.5x14 Screw x8
s1
V
Attach t2 Caster to
Panel V using b Bolt and
Nut.
Attach g1 Hinge Body to Panel V
using s1 Screws.
6x25 Bolt and Nut x1
b
Screw s4 Alignment Pin into
the top edge of Panel V.
Attach Panel V to Panel O4 with g1 Hinge
Body using s1 Screws.
g1
s1
X

Assembly InstructionsChrista 16
Step 2: Gate Legs and Support Panels
Caster x2
t2
6x25 Bolt and nut x2
b
Butt Hinge x6
h2
3.5x14 Screw x24
s1
Alignment Pin x3
s4
Magnet Plate x3
m
O2
O1
O3
Attach t2 Casters to the
bottom edges of Panels O1 and
O2.
Attach h2 Butt Hinges to
Panels O1 and O2 as
shown, using s1 Screws.
Screw s4 alignment pins into top
edges of Panels O1 and O2.
Attach m Magnet
Plates to the underside of
Panels O1 and O2 as shown,
using s1 Screws.
Set aside magnet for later use.
Attach h2 Butt Hinges to
Panel O3 as shown, using s1
Screws.
Screw s4 alignment
pin into top edge of
Panel O3.
Attach m Magnet Plate to the underside of Panel O3
as shown, using s1 Screws.
Set aside magnet for later use.
h2
s1

Assembly InstructionsChrista 17
Step 2: Gate Legs and Support Panels
O1
O2
D2
D1
3.5x14 Screw x12
s1
s1
Attach Panels O1 and O2 to
Panels D1 and D2 using s1
Screws.

Assembly InstructionsChrista 18
Step 2: Gate Legs and Support Panels
O3
Z
3.5x14 Screw x6
s1
Attach Panel O3 to Panel Z
using s1 Screws.
s1

Assembly InstructionsChrista 19
Step 3: Quilt Panels
Butt Hinge x6
h2
3.5x14 Screw x18
s1
Magnet x3
m
A1
A4
Attach m Magnets to Panel A1 using s2
Screws as shown.
Attach h2 Butt Hinges to Panel A1 using
s1 Screws as shown.
Attach m Magnet to Panel A4 using s2
Screws as shown. Set aside magnet plate
for later use.
Attach h2 Butt Hinges to Panel A4 using
s1 Screws as shown.
3x14 Screw x6
s2

Assembly InstructionsChrista 20
Step 3: Quilt Panels
3.5x14 Screw x18
s1
O2
O1
A1
O3
A4
Extend Gate Leg Panels O1
and O2. Balance Panel A1
on gate legs and attach h2
Hinges to Panel D using s1
Screws.
Extend Support Panel O3.
Balance Panel A4 on support
panels and attach h2 Hinges
to Panel Z using s1 Screws.
s1
h2
NOTE: The illustrations below show the cabinet from behind and underneath to
better show hinge attachment placement.
Z