Arrow HAFD233 User manual

3 Stage Height Adjustable
Back-to-Back Desk (HAFD233)
Assembly Instructions
Carefully open the carton, and lay out the parts
on a protective surface to avoid damage. Check
pack contents against the parts list to ensure all
components have been recieved. Do not use damaged
or defective parts. Carefully read all instructions before
starting assembly of the desk.
UNPACKING INSTRUCTIONS

PARTS OVERVIEW
OPTIONAL SCREEN BRACKET PARTS LIST
Part Description Qty Part Description Qty
11
Screen
Bracket 2C
M6 x 16
4
H
ST4.2 x 13
8
OPTIONAL CABLE TRAY PARTS LIST
Part Description Qty Part Description Qty
10
Central Cable Tray
1C
M6 x 16
4
DESK FRAME PARTS LIST
Part Description Qty Part Description Qty
1Left
Lifting Column
2A
M6 x 10 CSK
4
2
Right Lifting Column
2B
M6 x 10
4
3
Cable Tidy Tray
2C
M6 x 16
12
4
Supporting Beam
w/ Control Box 2D
ST4.2 x 19
16
5
Desktop Cross Beam
4F
Allen Key
4mm 1
6
Mains Power Lead
2
7
Hand Switch
2
There are 2 screw
kits in total
LEG BEAM PARTS LIST
Part Description Qty Part Description Qty
8
Leg Beam
2E
M8 x 16
8
9
Decorative Cover
4G
Allen Key
5mm 1
8
9
10
11

Install the lifting columns (1 & 2).
Install the leg beams (8).
TOP TIP
For each component, always start
all screws in their threads before
tightening any screw fully.
STEP 1
STEP 2
STEP 3 OPTIONAL Install the screen bracket screws.
Cx16
Ex8
Cx4
G
5mm
F
4mm
F
4mm
Please pay attention to the left or
right lifting column.
Insert the lifting columns (1 & 2)
into the ends of the supporting
beam (4). Fix with screws (C)
and allen key (E).
Connect the columns (1 & 2) to the leg beam (8)
with screw (E) and tighten with 5mm allen key (G).
Note the leg beam
orientation: the side
with the rivet nut
facing inwards. Attach plastic cover
E
Start the screws (C) into the leg beam (8) with
4mm allen key (F) but do not tighten completely.
Screws not
fully tightened
Leg beam (8)

Install the central cable tray (10).
STEP 4 OPTIONAL
STEP 5 OPTIONAL
Install the screen brackets (11).
F
4mm
F
4mm
Leg beam (8)
Screen
bracket (11)
Screen
bracket (11)
Keyhole slot
Take the cover o the central cable tray (10) and tighten the screws (C)
with the 4mm allen key (F), then slide the cover into place.
Central cable tray
Central cable tray
Loosen
Central cable tray
Tighten
Loosen the screws underneath the central cable tray
(10) with the 4mm allen key (F), slide apart to t and
hook the cable tray onto the keyhole slot. Extend
the cable tray and hook the other end.
Stretch

Install the desktop cross beam (5).
STEP 6
Connect cables (6 & 7) to control box.
STEP 7
Install the desktop and hand switches (7).
STEP 8
F
4mm
Ax4
Dx24 F
4mm
Connect the desktop cross beam (5) to the supporting beam (4)
with screws (A) and tighten the screws with 4mm allen key (F).
Connect the desktop cross
beam (5) to the supporting
beam (4) with screws (A)
and tighten the screws
with 4mm allen key (F).
Power port
Ports for cables
connected to
lifting columns
(1 & 2)
Port for hand
switch (7)
Tighten the screws underneath
the central cable tray (10)
with 4mm allen key (F).
The expansion distance of the
supporting beam (4) can be adjusted
according to the actual use.
Loosen
Adjust
Tighten