Arrow Harriet 305 User manual

Harriet
ASSEMBLY INSTRUCTIONS
ITEM NO.: 305 Teak
311 Ash White

Assembly InstructionsHarriet 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Phillips Screwdriver Hammer Electric Screwdriver
Torque set to 3-5
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
Rubber Mallet
Use and Care Your cabinet normally requires a minimum amount of maintenance; however, the
following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT
use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant.

Assembly InstructionsHarriet 3
Parts List: Panels
ITEM DESCRIPTION QTY BOX
LLeaf Support Wing 1 1 of 3
JCompartment Bottom 1 1 of 3
IShelf 1 1 of 3
HCompartment Back 1 1 of 3
TDrawer Left Side 4 1 of 3
SDrawer Right Side 4 1 of 3
RDrawer Back 4 1 of 3
A/B/C Top & leaves (pre-assembled) 1 1 of 3
NFront 1 2 of 3
PDrawer Fronts 4 2 of 3
Lift and Hardware Box 1 2 of 3
ITEM DESCRIPTION QTY BOX
VDoor Bin Sides 2 2 of 3
UDoor Bin Front 1 2 of 3
WDoor Bin Bottom 1 2 of 3
GBack 1 2 of 3
ODoor 1 2 of 3
DLeft Side 1 3 of 3
ERight Side 1 3 of 3
FCenter Partition 1 3 of 3
MLift Platform 1 3 of 3
QDrawer Bottoms 4 3 of 3
A
D
E
F
G
H
I
N
P
U
W
V
T
S
R
Q
M
C
B
V
L
J
O
x4

Assembly InstructionsHarriet 4
Parts List: Hardware
TIP: Keep all the parts in their individually labeled bags. This will make finding parts easier as you assemble your cabinet.
12mm Cam Lock x27
10mm Cam Lock x16
Large Cam Bolt x27
#6x1” Flathead Screw x32
Small Cam Bolt x16
Strike Plate x1
Door Magnet x1 #6x5/8”
Gold Panhead Screws x2
Handle x5 4x19 Fix Bolt x10
4x14 Screw x30 Drawer Runners x8
Drawer Stoppers x4
Door Hooks x4
#8x5/8” Screws x8 Metal Dowels x4
Caster Clip x5
Caster Insert x5 Non-Locking Casters x3
Locking Casters x2
Support Hinge x2
#7x5/8” Flathead
Screw x9
Self-Sticking Rubber
Tab x1
Lift Rail
(Left) x1
Lift Rail
(Right) x1
Lift x1
Flush Hinge x3
Wood Dowel x14
#10x1-1/4”
Flathead Screw x16
Caster Bracket x1
Wrench x1
50mm Non-Locking Caster x1

Assembly InstructionsHarriet 5
Step 1: Cabinet Shell - Back and Left Panel
G
12mm Cam Lock x6
Long Cam Bolts x6
Lift Rail
(Left) x1
4x14 Screw x3
D
Insert 4 Cam Locks into Panel G. Be sure that the arrow
on the cam lock is pointing toward the edge of the panel
(as shown at left).
Attach the following hardware to Panel D:
- 2 Cam Locks
- 6 Long Cam Bolts
- the Lift Rail (Left), using 4x14 Screws

Assembly InstructionsHarriet 6
Step 1: Cabinet Shell - Right Panel
E
E
12mm Cam Lock x2
Drawer Runners x4
#6x1” Flathead Screws x16
Long Cam Bolts x4
Metal Dowels x4
Drawer Stoppers x4 Attach the following to Panel E:
- 2 12mm Cam Locks
- 4 Long Cam Bolts
- 4 Drawer Runners with #6x1”
Flathead Screws
Once the Cam Locks, Cam Bolts and Drawer Runners are
attached to Panel E, attach 4 Drawer Stops with 4x14
Screws, and insert 4 Metal Dowels as shown.
NOTE: Do not tighten the screws completely. Make sure
you leave enough space for the drawer stopper to swivel.
4x14 Screw x4

Assembly InstructionsHarriet 7
Step 1: Cabinet Shell - Partition Panel
F
F
Side One
Side Two
12mm Cam Lock x1
Drawer Runners x4
#6x1” Flathead Screws x16
Long Cam Bolts x10
Lift Rail
(Right) x1
4x14 Screw x3
Attach the following to Panel F (Side One):
- 1 12mm Cam Lock
- 4 Long Cam Bolts
- 4 Drawer Runners with #6x1” Flathead Screws
Flip Panel F over.
Attach to Panel F (Side Two):
- 6 Long Cam Bolts
- Lift Rail (Right), using 4x14 Screws
- Magnet with #6x5/8” Screws
NOTE: When installing the Magnet, make sure that the magnetic side is facing the front edge of Panel F as shown.
Door Magnet x1
#6x5/8” Gold
Panhead Screws x2

Assembly InstructionsHarriet 8
Step 1: Cabinet Shell - Front, Shelf, and Drawer Compartment
12mm Cam Lock x16 Insert 4 12mm Cam Locks into Panel I.
N
I
J
H
Insert 4 12mm Cam Locks into Panel N.
Insert 4 12mm Cam Locks into Panel J.
Insert 4 12mm Cam Locks into Panel H.

Assembly InstructionsHarriet 9
Step 2: Cabinet Shell - Assembly
D
G
D
I
N
Slide Cam Bolts on Panel D into Cam Locks
on Panels I and N shown.
Tighten the Cam Locks by turning 180°
clockwise.
Lay Panel D on the floor as shown, and slide the Cam Bolts
on Panel D into Cam Locks on Panel G as shown.
Tighten the Cam Locks by turning 180° clockwise.
180°
Remember to tighten the Cam Locks!

Assembly InstructionsHarriet 10
Step 2: Cabinet Shell - Assembly
180°
Remember to tighten the Cam Locks!
F
G
N
I
Carefully lower Panel F, sliding the Cam Bolts on Panel F into
Cam Locks on Panels G, I and N as shown.
Tighten the Cam Locks by turning 180° clockwise.
Carefully lower Panels H and J, sliding the Cam Bolts on
Panel F into Cam Locks on Panels H and J as shown.
Tighten the Cam Locks by turning 180° clockwise.
H
J
F

Assembly InstructionsHarriet 11
Step 2: Cabinet Shell - Assembly
Carefully lower Panel E, sliding the Cam Bolts on Panel E
into Cam Locks on Panels H and J as shown.
Tighten the Cam Locks by turning 180° clockwise.
Flip the cabinet over so that it is upside down.
You may need a friend to help you,but it is not required.
180°
Remember to tighten the Cam Locks!
H
J
E

Assembly InstructionsHarriet 12
Step 3: Cabinet Shell - Casters
Caster Clip
FIRST
Caster Insert
SECOND
Caster
THIRD
Caster Clip x5
Caster Insert x5 Non-Locking Casters x3
Locking Casters x2
1. Place the Caster Clip.
2. Insert Caster Insert. Use
a wooden block or other
hard, flat item to protect the
Caster Insert and pound
into place with a hammer.
3. Use a rubber mallet
to pound the Caster
into place.
Flip the cabinet over so that it is up on its wheels.
You may need a friend to help you,but it is not required.
NOTE: Casters must be
installed in this order:
NOTE: Locking casters must be
installed at the front of the
cabinet as shown!

Assembly InstructionsHarriet 13
Step 4: Lift Installation
LIFT INSTALLATION WARNING:
DO NOT remove the small wooden block from the Lift until assembly is complete. If the block is removed or falls out
before lift assembly is complete, the cables will retract, making installation more difficult. If the
block falls out before complete assembly, Please call Customer Service at 1-800-533-7347,
ext. 1 for assistance, or visit www.arrowsewing.com/assembly and find the
“Alternate Airlift Attachment Steps” video.
This illustration shows the back view of the Lift. Notice the
wooden block and zip tie; the wooden block holds the piston
in place so that the cables can be easily handled and inserted
into the Lift Rails installed on your cabinet.
Lift x1
4x14 Screw x4
M
Attach the Lift to Panel M using
4x14 Screws.

Assembly InstructionsHarriet 14
Step 4: Lift Installation
Lift rail
Plastic guides on Lift
Rail tabs Lift rail
Cable
Guide Lift onto Lift Rails using plastic guides. Insert ends of cable into rail tabs; make sure the cable is hooked into the rail
tabs on both sides.
Cut the zip tie on the wooden block, but DO NOT remove the block yet.
Lower the Lift to first lock position and remove the wooden block. DO NOT ADJUST LIFT POSITION until the top is installed,
or you risk the Lift coming out and cables becoming disengaged.
M

Assembly InstructionsHarriet 15
Step 5: Top Panel
Long Cam Bolts x5
Attach Cam Bolts to Panel A as shown.
NOTE: Left and Right Leaves
(Panels B and C) come
pre-attached.
Carefully lower Panel A, inserting Cam Bolts
into Cam Locks on Panels D, F, and E.
Tighten the Cam Locks by turning 180°
clockwise.
180°
Remember to tighten the Cam Locks!
C
D
F
E
B
IMPORTANT NOTE: to avoid damage to
your cabinet, DO NOT extend leaves with-
out proper leaf support!
A

Assembly InstructionsHarriet 16
Step 6: Leaf Support
L
E
Support Hinge x2
#7x5/8” Flathead
Screw x8
Self-Sticking
Rubber Tab x1
Attach Support
Hinges to Leaf
Support Panel
Las shown,
using #7x5/8”
Screws.
Attach Leaf Support Panel L
to Panel E as shown, using
#7x5/8” Screws.
L
Adhere the Self-Sticking
Rubber Tab to Panel L
so that it is off-center on
the edge of the panel as
shown above.

Assembly InstructionsHarriet 17
Step 7: Door - Door Bin
10mm Cam Lock x14
Short Cam Bolt x9
Attach 2 Short Cam Bolts into each Panel V piece.
Insert 4 10mm Cam Locks into each Panel V piece.
Insert 6 10mm Cam Locks into Panel W.
Attach 5 Short Cam Bolts into Panel U.
V
V
W
U

Assembly InstructionsHarriet 18
Step 7: Door - Door Bin
Remember to tighten the Cam Locks!
V
V
W
U
V
W
V
Attach bin sides (Panel V pieces) to Panel W.
Tighten the Cam Locks by turning 180° clockwise.
Attach Panel V/Panel W Assembly to Panel U.
Tighten the Cam Locks by turning 180° clockwise.

Assembly InstructionsHarriet 19
Step 7: Door
4x14 Screw x14
Flush Hinge x3
Short Cam Bolt x5
Door Hooks x4
#5x5/8” Flathead
Screw x1
Magnet Strike Plate x1
Remember to tighten the Cam Locks!
Attach 4 Door Hooks
using 4x14 Screws. Attach 3 Flush Hinges
using 4x14 Screws.
Attach Magnet Strike Plate
using #5x5/8” Screw.
Attach 4 Short Cam Bolts.
Lower the door bin onto the door,
inserting Cam Bolts on Panel O into
Cam Locks on Panels V and W.
Tighten the Cam Locks by turning
180° clockwise.
O
O
V
V
W
Attach Caster Bracket to
Panel O using
4x14 Screws.
Insert Caster into Caster Bracket and
tighten with Wrench.
50mm Non-Locking Caster x1
Caster Bracket x1

Assembly InstructionsHarriet 20
Step 7: Door
Handle x1 4x20 Fix Bolt x2
4x14 Screw x6
Attach Hinges on Door to Panel D
using 4x14 Screws as shown.
D
Attach Handle to Door using 4x20
Fix Bolts as shown.
O