Arrow Laverne 451 User manual

Laverne
ASSEMBLY INSTRUCTIONS
ITEM NO.: 451 White
455 Teak

Assembly InstructionsLaverne 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Phillips Screwdriver Hammer Electric Screwdriver
Torque set to 3-5
Use and Care Your cabinet normally requires a minimum amount of maintenance; however, the
following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT
use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant.

Assembly InstructionsLaverne 3
Parts List: Panels
A2
A1
A4
A3
Y2
O2
Y1
Y
O1
O2
G
D
Z
X
ITEM DESCRIPTION QTY. PACK.
A1 Top Panel 1 2 of 3
DBack Panel 1 2 of 3
XLeft Side Panel 1 1 of 3
ZRight Side Panel 1 1 of 3
O1 Left Side Stabilizing Panel 1 2 of 3
GBottom Panel 1 2 of 3
ITEM DESCRIPTION QTY. PACK.
A2 Quilt Leaf Panel 1 2 of 3
A4 Cover Panel 1 2 of 3
A3 Lift Panel 1 1 of 3
Y2 Center Panel 1 1 of 3
O2 Insert Holder 2 1 of 3
YGate Leg Panel 1 1 of 3
Y1 Gate Leg Panel 1 1 of 3
Hardware & Lift 3 of 3

Assembly InstructionsLaverne 4
Parts List: Hardware
6x35 Cam Bolt x34 5⁄8“ Cam Cover x34 8x30 Dowel Pin x34
d1
c1
c2
3.5x16 Screw x34
s1
4x16 Screw x34
s2
6x25 Bolt and nut x2
b
Hinge x3
h2
Plate Caster x6
t1
Caster x2
t2
Hinge x4
h1
Metal Support Bar x1
Lift Rail
(Right) x1
Lift Rail
(Left) x1
Lift x1
Alignment Pin x2
a
TIP: Keep all the parts in their individually labeled bags. This will make finding parts easier as you assemble your cabinet.
3x30 Screw x4
s3

Assembly InstructionsLaverne 5
Plate Caster x6
t1
3.5x16 Screw x24
s1
6x35 Cam Bolt x15
c1
Step 1: Cabinet Shell
Attach t1 Plate Casters to Panel G using s1
Screws.
Flip Panel G over.
Attach c1 Cam Bolts to Panel G.
G
G
Congratulations and welcome to Arrow Sewing Furniture! We can’t wait to get your brand new Laverne Sewing Cabinet up and
running. Please contact our Customer Service Team at 1-800-533-7347 ext. 1 during normal business hours with any assembly
related questions.

Assembly InstructionsLaverne 6
8x30 Dowel Pin x16
d1
5⁄8“ Cam Cover x4
c2
Step 1: Cabinet Shell
x2
O2
Insert 2 d1 Dowel Pins into each of the
two O2 Panels.
Attach the two O2 Panels to Panel G as shown.
Tighten cam locks and apply c2 Cam Covers.
Set Panel G aside.
O2
O2
G
D
Attach d1 Dowel Pins to Panel D.
Attach c1 Cam Bolts to Panel D.
6x35 Cam Bolt x2
c1

Assembly InstructionsLaverne 7
Step 1: Cabinet Shell
6x35 Cam Bolt x2
c1
8x30 Dowel Pin x10
d1
3.5x16 Screw x6
s1
Lift Rail
(Right) x1
Lift Rail
(Left) x1
Attach 2 c1 Cam Bolts and 4 d1 Dowel Pins to Panel Z.
Attach Lift Rail (Right) to Panel Z using s1 Screws.
NOTE: There are two pre-drilled holes for the lift rail: top and bottom. Affix these screws
first, and then add a third screw in the center of the lift rail.
Attach 6 d1 Dowel Pins to Panel Y.
Attach Lift Rail (Left) to Panel Y using s1 Screws.
NOTE: There are two pre-drilled holes for the lift rail: top and bottom. Affix these screws
first, and then add a third screw in the center of the lift rail.
Z
Y
TIP: Spray a small amount of
WD-40 or similar lubricant onto a
paper towel and wipe the newly
installed rails. This will make lift
installation and operation easier.

Assembly InstructionsLaverne 8
X
O1
Step 1: Cabinet Shell
6x35 Cam Bolt x4
c1
8x30 Dowel Pin x8
d1
Attach 2 c1 Cam Bolts and 6 d1
Dowel Pins to Panel X.
Attach 2 c1 Cam Bolts and 2 d1
Dowel Pins to Panel O1.

Assembly InstructionsLaverne 9
Step 1: Cabinet Shell
X
D
Y
Z
O1
X
D
Y
Z
5⁄8“ Cam Cover x8
c2
Attach Panels X, Y and Z to Panel D
as shown.
Tighten cam locks and apply c2 Cam
Covers.
Attach Panel O1 to Panel X as shown.
Tighten cam locks and apply c2 Cam
Covers.

Assembly InstructionsLaverne 10
Step 2: Attaching the Base
5⁄8“ Cam Cover x11
c2
Attach Panel G to Panels O1, X, D, Y
and Z as shown.
Tighten cam locks and apply c2 Cam
Covers.
X
D
O1
Y
Z
G
Make sure casters are locked and
flip cabinet up onto its wheels. You
may need a friend to help you, but it
is not required.

Assembly InstructionsLaverne 11
Step 3: Lift
LIFT INSTALLATION WARNING:
DO NOT remove the small wooden block from the Lift until assembly is complete. If the block is removed or falls out
before lift assembly is complete, the cables will retract, making installation more difficult. If the
block falls out before complete assembly, Please call Customer Service at 1-800-533-7347,
ext. 1 for assistance, or visit www.arrowsewing.com/assembly and find the
“Alternative Airlift Attachment Steps” video.
3.5x16 Screw x4
s1
Attach the Lift to Panel
A4 using s1 Screws.
A4

Assembly InstructionsLaverne 12
Guide Lift onto Lift Rails using plastic guides.
Insert ends of cable into rail tabs; make sure the cable is hooked into the rail tabs on both sides.
NOTE: See Page 13 for close-up illustrations of Lift Panel assembly.
Cut the zip tie on the wooden block, but DO NOT remove the block yet.
Lower the Lift to first lock position and remove the wooden block.
DO NOT ADJUST LIFT POSITION until the top is installed, or you risk the Lift coming out and cables becoming
disengaged.
Step 3: Lift

Assembly InstructionsLaverne 13
Lift rail
Plastic guides on Lift
Rail tabs Lift rail
Cable
Step 3: Lift

Assembly InstructionsLaverne 14
Step 4: Attaching the Top
Metal Support Bar
6x35 Cam Bolt x11
c1
Metal Support Bar x1
c1
s3
A1
Attach c1 Cam Bolts to Panel A1 as shown.
Attach Metal Support Bar to Panel A1 using s3
Screws.
3x30 Screw x4
s3

Assembly InstructionsLaverne 15
Step 4: Attaching the Top
5⁄8“ Cam Cover x11
c2
Carefully lower top Panel A1 onto Panels O1, X, D, Y
and Z as shown.
Tighten cam locks and apply c2 Cam Covers.
A1
O1
X
D
Y
Z

Assembly InstructionsLaverne 16
Step 5: Gate Legs and Quilt Panel
Y
Y1
Hinge x4
h2
Alignment Pin x2
a
Caster x2
t2
Screw Alignment Pins into the
top edges of Panels Y and Y1.
Attach h2 Hinges
to Panels Y and Y1
using s2 Screws. Attach t2 Casters to Panels Y
and Y1 using b Bolt and Nut.
6x25 Bolt and nut x2
b
4x16 Screw x8
s2

Assembly InstructionsLaverne 17
Step 5: Gate Legs and Quilt Panel
s2
h2
Attach Gate Leg Panels Y and Y1 to Panel D using
s2 Screws.
4x16 Screw x8
s2
A2

Assembly InstructionsLaverne 18
Step 5: Gate Legs and Quilt Panel
4x16 Screw x9
s2
Hinge x3
h1
s2
h1
Attach h1 Hinges to Panel A2 as shown, using
s2 Screws.
A2

Assembly InstructionsLaverne 19
Step 5: Gate Legs and Quilt Panel
Extend Gate Leg Panels Y and Y1. Balance Panel A2 on gate legs and attach h1 Hinges to Panel A1
using s2 Screws.
s2
h1
4x16 Screw x9
s2

Assembly InstructionsLaverne 20
Completed Laverne Sewing Cabinet