Arrow SS900-B Use and care manual

Owner's Manual & Assembly Instructions
1Place two rear posts on a at surface parallel to
each other. Position shelves at desired locations
and fasten with bolts and nuts.
2Place front posts opposite the rear posts and
secure to shelves using bolts and nuts.
3Fasten braces to the inside of rear posts and
outside of front posts with bolts and nuts.
NOTE
First remove and reinsert bolt and nut fastening
bottom shelf to side leg of front post. Fasten
opposite end of brace to rear post.
66013
#8-32x1/4" (6 mm)
Bolt (26)
65103
#8-32 Hex Nut (26)
CAUTION: SOME PARTS HAVE SHARP EDGES.
CARE MUST BE TAKEN WHEN HANDLING THE
VARIOUS PIECES TO AVOID A MISHAP. WEAR
GLOVES WHEN HANDLING METAL PARTS. 717451111
SHELF
7053
Keep this Owner's Manual for future reference.
Wash off inked part numbers on coated shelves with soap and water.
If you nd a part is missing, include the model no. of your shelf and contact:
Arrow Shed, LLC Customer Service Dept.
1101 North 4th Breese, Illinois 62230
1-800-851-1085 or [email protected]
REAR POST
7057
FRONT POST
7056
BRACE
3903
1
STEP
3
STEP
Wall Shelf
Model No. SS900-B
697.68204-B
2
STEP

Mounting Instructions
ASSEMBLY PROCEDURE WHEN MOUNTING TO VERTICAL SIDED BUILDINGS WITH 60" (152,4 cm) WALL HEIGHT
1Locate shelf unit on desired wall. Drill two
1/4" (6 mm) dia. holes through upper wall
angle and wall panel 32 3/8" (82,2 cm) apart,
3/8" (10 mm) below top ange of angle.
2 Using a square or level measure down
29 1/2" (74,9 cm) from each hole. Check
bottom holes to make sure they are 32 3/8"
(82,2 cm) apart. Drill two 1/4" (6 mm) dia.
holes at these locations.
3 Temporarily remove the two bolts and nuts
from the back of the bottom shelf. Position
shelf aligning holes in rear posts with holes
drilled in panel and fasten with four #8-32x
1 1/2" (38 mm) bolts and nuts and either 3/4"
(19 mm) or 1" (25 mm) shims. Hardware for
mounting shelf unit is not supplied. Consult
your local hardware store for these parts.
1Follow directions for Steps 1 and 2 above.
2 Temporarily remove the two bolts and nuts
from the back of the bottom shelf. Position
shelf aligning holes in rear posts with holes
drilled in panel and fasten with four
#8-32x1/4" (6 mm) bolts provided, as shown.
* Shelf may be attached to horizontal sided buildings
if located between wall studs using this procedure.
ASSEMBLY PROCEDURE WHEN MOUNTING TO VERTICAL SIDED BUILDINGS WITH
62" (157,5 cm), 67" (170,2 cm) or 71 1/4" (181,0 cm) WALL HEIGHT*
ASSEMBLY PROCEDURE WHEN MOUNTING TO HORIZONTAL SIDED BUILDINGS OVER VERTICAL WALL STUDS
1Follow directions for Steps 1, 2 and 3 above. Drill 1/4" (6 mm) dia.
holes through siding
panel and angle
#8-32
Hex Nut
Drill 1/4" (6 mm) dia.
holes through wall panel
#8-32x1 1/2"
(38 mm) Bolt
3/8" (10 mm)
29 1/2" (74,9 cm)
Drill 1/4" (6 mm) dia. holes
through siding panel
3/4" (19 mm) or
1" (25 mm) Shim
#8-32x1 1/2"
(38 mm) Bolt
29 1/2" (74,9 cm)
3/8" (10 mm)
32 3/8"
82,2 cm
Temporarily
remove two bottom
bolts and nuts
Drill 1/4" (6 mm) dia.
holes through
wall panel
29 1/2" (74,9 cm)
Drill 1/4" (6 mm) dia. holes
through wall panel and angle
Drill 1/4" (6 mm) dia.
holes through wall panel and angle
3/8" (10 mm)
717451111
32 3/8"
82,2 cm
32 3/8"
82,2 cm
#8-32
Hex Nut
3/4" (19 mm) or
1" (25 mm) Shim