ASROCK WRX80 CREATOR User manual

Version 1.0
Published February 2022
Copyright©2022 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com

AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: [phone] ext.123 (Standard International call charges apply)
e terms HDMI®and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
INTEL END USER SOFTWARE LICENSE AGREEMENT
IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.
LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s Soware
only in its unmodied and binary form, (with the accompanying documentation, the
“Soware”) for Licensee’s personal use only, and not commercial use, in connection with
Intel-based products for which the Soware has been provided, subject to the following
conditions:
(a) Licensee may not disclose, distribute or transfer any part of the Soware, and You agree
to prevent unauthorized copying of the Soware.
(b) Licensee may not reverse engineer, decompile, or disassemble the Soware.
(c) Licensee may not sublicense the Soware.
(d) e Soware may contain the soware and other intellectual property of third party
suppliers, some of which may be identied in, and licensed in accordance with, an enclosed
license.txt le or other text or le.
(e) Intel has no obligation to provide any support, technical assistance or updates for the
Soware.
OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Soware
remains with Intel or its licensors or suppliers. e Soware is copyrighted and protected
by the laws of the United States and other countries, and international treaty provisions.
Licensee may not remove any copyright notices from the Soware. Except as otherwise
expressly provided above, Intel grants no express or implied right under Intel patents,
copyrights, trademarks, or other intellectual property rights. Transfer of the license termi-
nates Licensee’s right to use the Soware.
DISCLAIMER OF WARRANTY. e Soware is provided “AS IS” without warranty of
any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PUR-
POSE.
LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS
WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF
BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG

ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN
IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
LICENSE TO USE COMMENTS AND SUGGESTIONS. is Agreement does NOT
obligate Licensee to provide Intel with comments or suggestions regarding the Soware.
However, if Licensee provides Intel with comments or suggestions for the modication,
correction, improvement or enhancement of (a) the Soware or (b) Intel products or
processes that work with the Soware, Licensee grants to Intel a non-exclusive, worldwide,
perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under
Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments
and suggestions.
TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license
at any time if Licensee is in breach of any of its terms or conditions. Upon termination,
Licensee will immediately destroy or return to Intel all copies of the Soware.
THIRD PARTY BENEFICIARY. Intel is an intended beneciary of the End User License
Agreement and has the right to enforce all of its terms.
U.S. GOVERNMENT RESTRICTED RIGHTS. e Soware is a commercial item (as
dened in 48 C.F.R. 2.101) consisting of commercial computer soware and commercial
computer soware documentation (as those terms are used in 48 C.F.R. 12.212), consistent
with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide
the Soware to the U.S. Government. Contractor or Manufacturer is Intel Corporation,
2200 Mission College Blvd., Santa Clara, CA 95054.
EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries will
export/re-export the Soware, directly or indirectly, to any country for which the U.S.
Department of Commerce or any other agency or department of the U.S. Government
or the foreign government from where it is shipping requires an export license, or other
governmental approval, without rst obtaining any such required license or approval. In
the event the Soware is exported from the U.S.A. or re-exported from a foreign destina-
tion by Licensee, Licensee will ensure that the distribution and export/re-export or import
of the Soware complies with all laws, regulations, orders, or other restrictions of the U.S.
Export Administration Regulations and the appropriate foreign government.
APPLICABLE LAWS. is Agreement and any dispute arising out of or relating to it will
be governed by the laws of the U.S.A. and Delaware, without regard to conict of laws
principles. e Parties to this Agreement exclude the application of the United Nations
Convention on Contracts for the International Sale of Goods (1980). e state and federal
courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising
out of or relating to this Agreement. e Parties consent to personal jurisdiction and venue
in those courts. A Party that obtains a judgment against the other Party in the courts iden-
tied in this section may enforce that judgment in any court that has jurisdiction over the
Parties.
Licensee’s specic rights may vary from country to country.

CE Warning
is device complies with directive 2014/53/EU issued by the Commision of the European
Community.
is equipment complies with EU radiation exposure limits set forth for an uncontrolled
environment.
is equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Operations in the 5.15-5.35GHz band are restricted to indoor usage only.
Radio transmit power per transceiver type
Function Frequency Maximum Output Power (EIRP)
WiFi
2400-2483.5 MHz 18.5 + / -1.5 dbm
5150-5250 MHz 21.5 + / -1.5 dbm
5250-5350 MHz 18.5 + / -1.5 dbm (no TPC)
21.5 + / -1.5 dbm (TPC)
5470-5725 MHz 25.5 + / -1.5 dbm (no TPC)
28.5 + / -1.5 dbm (TPC)
Bluetooth 2400-2483.5 MHz 8.5 + / -1.5 dbm

Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 8
1.4 I/O Panel 11
1.5 802.11ax Wi-Fi 6E Module and ASRock WiFi 2.4/5/6 GHz
Antenna 13
1.6 ASRock Thunderbolt™ 4 Module 14
Chapter 2 Installation 18
2.1 Installing the CPU 19
2.2 Installing the CPU Cooler 23
2.3 Installation of Memory Modules (DIMM) 25
2.4 Expansion Slots (PCIe Slots) 27
2.5 Jumpers Setup 28
2.6 Onboard Headers and Connectors 29
2.7 Smart Switches 37
2.8 Dr. Debug 38
2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1) 44
2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2) 48
Chapter 3 Software and Utilities Operation 52
3.1 Installing Drivers 52

3.2 ASRock Motherboard Utility (A-Tuning) 53
3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 53
3.2.2 Using ASRock Motherboard Utility (A-Tuning) 53
3.3 ASRock Live Update & APP Shop 56
3.3.1 UI Overview 56
3.3.2 Apps 57
3.3.3 BIOS & Drivers 60
3.3.4 Setting 61
3.4 ASRock Polychrome SYNC 62
Chapter 4 UEFI SETUP UTILITY 65
4.1 Introduction 65
4.1.1 UEFI Menu Bar 65
4.1.2 Navigation Keys 66
4.2 Main Screen 67
4.3 OC Tweaker Screen 68
4.4 Advanced Screen 72
4.4.1 CPU Conguration 73
4.4.2 Onboard Devices Conguration 74
4.4.3 Storage Conguration 76
4.4.4 ACPI Conguration 77
4.4.5 Super IO Conguration 78
4.4.6 Serial Port Console Redirection 79
4.4.7 Trusted Computing 82
4.4.8 AMD Mem Conguration 84

4.5 Tools 85
4.6 Server Mgmt 86
4.7 H/W Monitor 91
4.8 Security Screen 93
4.9 Boot Screen 94
4.10 Exit Screen 95

English
1
WRX80 Creator
Chapter 1 Introduction
ank you for purchasing ASRock WRX80 Creator motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.
1.1 Package Contents
• ASRock WRX80 Creator Motherboard (EATX Form Factor)
• ASRock WRX80 Creator Quick Installation Guide
• ASRock WRX80 Creator Support CD
• 4 x Serial ATA (SATA) Data Cables (Optional)
• 1 x ASRock WiFi 2.4/5/6 GHz Antenna (Optional)
• 2 x Screws for M.2 Sockets (Optional)
• 2 x Standos for M.2 Sockets (Optional)
Because the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any modi-
cations of this documentation occur, the updated version will be available on ASRock’s
website without further notice. If you require technical support related to this mother-
board, please visit our website for specic information about the model you are using. You
may nd the latest VGA cards and CPU support list on ASRock’s website as well. ASRock
website http://www.asrock.com.

English
2
1.2 Specications
Platform • EATX Form Factor
• 14 Layer PCB
• 2oz Copper PCB
CPU • Supports AMD Socket sWRX8 for AMD Ryzen™
readripper™ PRO 5000WX and 3000WX Series Processors
• Intersil Digital PWM
• 8 Power Phase design
• Supports ASRock Hyper BCLK Engine III
Chipset • AMD WRX80
Memory • Eight Channel DDR4 Memory Technology
• 8 x DDR4 DIMM Slots
• Supports DDR4 ECC & non-ECC, buered and un-buered
memory (U-DIMM) up to 4533+(OC)*
• Supports DDR4 3200/2933/2667/2400/2133 ECC & non-
ECC, buered and un-buered memory (R-DIMM and 3DS
R-DIMM)*
* Supports DDR4 3200 natively.
• Max. capacity of system memory: 2048 GB
• 15μ Gold Contact in DIMM Slots
Expansion
Slot
CPU:
• 7 x PCIe 4.0 x16 Slots (PCIE1/PCIE2/PCIE3/PCIE5/PCIE7
at x16; PCIE4/PCIE6 at x8)*
Chipset:
• 1 x Vertical M.2 Socket (Key E), supports type 2230 WiFi/BT
PCIe WiFi module
* Supports NVMe SSD as boot disks
• 15μ Gold Contact in VGA PCIe Slots (PCIE1, PCIE2 ,PCIE3,
PCIE5 and PCIE7)

English
3
WRX80 Creator
Thunder-
boltTM
• Intel® JHL8540 underboltTM 4 Controller
• Supports underboltTM 4 interface with max. resolution of
5K (5120 x 2880) @ 60Hz for one display over a single cable
connection
• Supports underboltTM 4 interface with max. resolution of
4K x 2K (4096x2160) @ 60Hz for dual displays over a single
cable connection
* DisplayPort or USB-C monitor is not supported on the
underboltTM 4 Type-C Ports
* A discrete graphics card is required for underbolt display
Graphics • Aspeed® AST2500 BMC Controller
• Supports D-Sub with max. resolution up to 1920x1200 @
60Hz
Audio • 7.1 CH HD Audio (Realtek ALC4050H+ALC1220)
• Premium Blu-ray Audio support
• Supports Surge Protection
• NE5532 Premium Headset Amplier for Front Panel Audio
Connector (Supports up to 600 Ohm headsets)
• Pure Power-In
• Direct Drive Technology
• PCB Isolate Shielding
• Impedance Sensing on Rear Out port
• Individual PCB Layers for R/L Audio Channel
• Gold Audio Jacks
• 15μ Gold Audio Connector
• Nahimic Audio
LAN 2 x 10 Gigabit LAN 100/1000/2500/5000/10000 Mb/s (Intel®
X710-AT2)
• Supports Lightning/ESD Protection
• Supports Energy Ecient Ethernet 802.3az
• Supports PXE
1 x Dedicated IPMI (ASPEED AST2500)
• Supports iKVM and vMedia

English
4
Wireless
LAN
• 802.11ax Wi-Fi 6E Module
• Supports IEEE 802.11a/b/g/n/ax
• Supports Dual-Band 2x2 160MHz with extended 6GHz
band* support
* Wi-Fi 6E (6GHz band) will be supported by Microso®
Windows® 11. e availability will depend on the dierent
regulation status of each country and region. It will be activated
(for supported countries) through Windows Update and
soware updates once available.
* A 6GHz compatible router is required for 6E functionality.
• 2 antennas to support 2 (Transmit) x 2 (Receive) diversity
technology
• Supports Bluetooth + High speed class II
• Supports MU-MIMO
Rear Panel
I/O
• 2 x Antenna Ports
• 1 x D-Sub Port
• 1 x Optical SPDIF Out Port
• 2 x USB 4.0 underboltTM 4 Type-C Ports (40 Gb/s for USB
4.0 protocol; 40Gb/s for underbolt protocol) (Supports
ESD Protection)*
* Supports USB-PD 3.0 9V/3A(27W) and 5V/3A(15W)
• 2 x Mini DisplayPort Input Ports**(For underbolt)
** Please choose regular mini DisplayPort to DisplayPort
adapter cables instead of right angled ones if you use two mini
DisplayPort input ports simultaneously.
• 4 x USB 3.2 Gen2 Ports (10 Gb/s) (Supports ESD
Protection)***
*** Ultra USB Power is supported on USB31_1_2 ports.
*** ACPI wake-up function is not supported on USB31_1_2
ports.
• 2 x USB 3.2 Gen1 Ports (Supports ESD Protection)
• 2 x RJ-45 LAN Ports with LED (ACT/LINK LED and SPEED
LED)
• 1 x RJ45 Dedicated IPMI LAN Port with LED (ACT/LINK
LED and SPEED LED)
• 1 x Clear CMOS Button
• HD Audio Jacks: Rear Speaker / Central / Line in / Front
Speaker / Microphone (Gold Audio Jacks)

English
5
WRX80 Creator
Storage CPU:
• 1 x Hyper M.2 Socket (M2_1, Key M), supports type
2260/2280/22110 SATA3 6.0 Gb/s & PCIe Gen4x4 (64 Gb/s)
modes*
Chipset:
• 1 x Hyper M.2 Socket (M2_2, Key M), supports type
2260/2280 PCIe Gen4x4 (64 Gb/s) mode*
• 8 x SATA3 6.0 Gb/s Connectors
• 1 x U.2 Connector
* Supports NVMe SSD as boot disks
* Supports ASRock U.2 Kit
RAID • Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA
storage devices
• Supports RAID 0, RAID 1 and RAID 5 for M.2 NVMe stor-
age devices*
* Requires additional M.2 NVMe expansion cards to support
RAID 5
Connector • 1 x SPI TPM Header
• 1 x COM Port Header
• 1 x Intelligent Platform Management Bus Header
• 1 x PSU SMBus Header
• 1 x BMC SMBus Header
• 1 x Auxiliary Panel Header
• 1 x Power LED and Speaker Header
• 1 x RGB LED Header
* Supports in total up to 12V/3A, 36W LED Strip
• 2 x Addressable LED Headers
* Support in total up to 5V/3A, 15W LED Strip
• 1 x CPU Fan Connector (4-pin)
* e CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.
• 1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan
Speed Control)
* e CPU/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.

English
6
• 3 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan
Speed Control)
* e Chassis/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.
* CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP and
CHA_FAN3/WP can auto detect if 3-pin or 4-pin fan is in use.
• 1 x 24 pin ATX Power Connector (Hi-Density Power
Connector)
* We recommend using a PSU with a max. current of 3A on
+5VSB.
• 2 x 8 pin 12V Power Connectors (Hi-Density Power
Connector)
• 1 x 6 pin 12V Power Connector (Hi-Density Power
Connector)
• 1 x Front Panel Audio Connector (15μ Gold Audio
Connector)
• 1 x Right Angle Front Panel Audio Connector*
* Connect the audio device to either one of the audio connec-
tors.
• 1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Supports
ESD Protection)
• 2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)
(Supports ESD Protection)
• 1 x Front Panel Type C USB 3.2 Gen2 Header (Supports ESD
Protection)
• 1 x Non Maskable Interrupt Button Header
• 1 x Dr. Debug with LED
• 1 x Power Button with LED
• 1 x Reset Button
BIOS
Feature
• AMI UEFI Legal BIOS with GUI support
• Supports “Plug and Play”
• ACPI 5.1 compliance wake up events
• Supports jumperfree
• SMBIOS 2.3 support
• CPU, CPU VDDCR_SOC, DRAM, VPPM, PREM VDD_
CLDO, PERM VDDCR_SOC, +1.8V, VDDP Voltage Multi-
adjustment

English
7
WRX80 Creator
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using third-party
overclocking tools. Overclocking may aect your system’s stability, or even cause damage to
the components and devices of your system. It should be done at your own risk and expense.
We are not responsible for possible damage caused by overclocking.
* For detailed product information, please visit our website: http://www.asrock.com
Hardware
Monitor
• Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water
Pump Fans
• Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans
• Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/
Water Pump Fans
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, CPU
VDDCR_SOC, DRAM, PREM VDDCR_SOC, +1.8V
OS • Microso® Windows® 10 64-bit / 11 64-bit
Certica-
tions
• FCC, CE
• ErP/EuP ready (ErP/EuP ready power supply is required)
• CEC Tier II ready

English
8
PCIE1
LAN1
Top:
Central/Bass
Center:
REAR SPK
Top:
LINE IN
Center:
FRONT
Bottom:
Optical
SPDIF
Bottom:
MIC IN
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPK_PLED1
AUX_PANEL1
GFX_12V1
12
18
19
23
USB_1_2
1
1
31
3457
6
38
Dr.
Debug
32
M2_1
CHA_FAN2
/WP
USB3_5_6
27
BIOS
ROM
ATX12V1
VGA_CON1
AMD
WRX80
34
RGB_LED1
1
33
ADDR_LED1
ADDR_LED2
1
1
M2_2
1
HD_AUDIO1
ATXPWR1
CLRCMOS1
1
28
F_USB31_TC_1
8
10
11
2
1
CHA_FAN1
/WP
36
39
USB 3.2 Gen1
T: USB3_1
B: USB3_2
37
LAN
WRX80 CREATO R
ATX12V2
CPU_FAN2
/WP
CHA_FAN3
/WP
PSU_SMB1
9
1
TPM_BIOS_PH1
13
1
15
17
SATA3_8
SATA3_7
SATA3_6
SATA3_5
SATA3_4
SATA3_3
SATA3_2
SATA3_1
20
21
22
24
U2_1
COM1
HD_AUDIO
_RA1
1
IPMB1
1
BMC_SMB1
NMI_BTN1
1
1
DDR4_H1 (64 bit, 288-pin module), Blue
DDR4_G1 (64 bit, 288-pin module), White
DDR4_F1 (64 bit, 288-pin module), Blue
DDR4_E1 (64 bit, 288-pin module), White
CPU_FAN1
DDR4_A1 (64 bit, 288-pin module)
DDR4_B1 (64 bit, 288-pin module)
DDR4_C1 (64 bit, 288-pin module)
DDR4_D1 (64 bit, 288-pin module)
14
16
1
USB3_3_4
PCIE2
PCIE3
PCIE4
PCIE5
PCIE6
PCIE7
M2_WIFI_1
CLRC
BTN2
TBT_M2_1
TBT_M2_2
USB 3.2 Gen2
T: USB31_1
B: USB31_2
1
USB 3.2 Gen2
T: USB31_4
B: USB31_3
IPMI
LAN
1
30
35
40
25
26
AUDIO
CODEC
29
LAN_2
RSTBTN1
ASPEED
AST2500
1.3 Motherboard Layout

English
9
WRX80 Creator
No. Description
1VGA Header (VGA_CON1)
2 8 pin 12V Power Connector (ATX12V2)
3 8 pin 12V Power Connector (ATX12V1)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_C1)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_B1, DDR4_D1)
6 CPU Fan Connector (CPU_FAN1)
7 CPU / Waterpump Fan Connector (CPU_FAN2/WP)
8 RGB LED Header (RGB_LED1)
9 Addressable LED Header (ADDR_LED2)
10 Chassis / Waterpump Fan Connector (CHA_FAN3/WP)
11 PSU SMBus Header (PSU_SMB1)
12 ATX Power Connector (ATXPWR1)
13 SPI TPM Header (TPM_BIOS_PH1)
14 2 x 288-pin DDR4 DIMM Slots (DDR4_E1, DDR4_G1)
15 Front Panel Type C USB 3.2 Gen2 Header (F_USB31_TC_1)
16 2 x 288-pin DDR4 DIMM Slots (DDR4_F1, DDR4_H1)
17 Chassis / Waterpump Fan Connector (CHA_FAN2/WP)
18 USB 3.2 Gen1 Header (USB3_5_6)
19 SATA3 Connectors (SATA3_8)(Upper), (SATA3_7)(Lower)
20 SATA3 Connectors (SATA3_6)(Upper), (SATA3_5)(Lower)
21 SATA3 Connectors (SATA3_4)(Upper), (SATA3_3)(Lower)
22 SATA3 Connectors (SATA3_2)(Upper), (SATA3_1)(Lower)
23 Power LED and Speaker Header (SPK_PLED1)
24 6 pin 12V Power Connector (GFX_12V1)
25 Clear CMOS Jumper (CLRMOS1)
26 U.2 Connector (U2_1)
27 System Panel Header (PANEL1)
28 Auxiliary Panel Header (AUX_PANEL1)
29 Power Button (PWRBTN1)
30 Reset Button (RSTBTN1)
31 USB 3.2 Gen1 Header (USB3_3_4)
32 USB 2.0 Header (USB_1_2)
33 Chassis / Waterpump Fan Connector (CHA_FAN1/WP)

English
10
No. Description
34 Addressable LED Header (ADDR_LED1)
35 Non Maskable Interrupt Button (NMI_BTN1)
36 BMC SMBus Header (BMC_SMB1)
37 Intelligent Platform Management Bus Header (IPMB1)
38 COM Port Header (COM1)
39 Right Angle Front Panel Audio Header (HD_AUDIO_RA1)
40 Front Panel Audio Header (HD_AUDIO1)

English
11
WRX80 Creator
1.4 I/O Panel
No. Description No. Description
1 VGA Port 10 10G LAN RJ-45 Port (LAN1)**
2 LAN RJ-45 Port (IPMI_LAN)* 11 USB 3.2 Gen2 Ports (USB31_3_4)
3 10G LAN RJ-45 Port (LAN_2)** 12 Mini DisplayPort Input Ports****
4Central (Orange) 13 USB 4.0 underboltTM 4 Type-C Ports
5 Rear Speaker (Black) 14 Antenna Ports
6 Line In (Light Blue) 15 USB 3.2 Gen2 Ports (USB31_1_2)*****
7 Front Speaker (Lime)*** 16 USB 3.2 Gen1 Ports (USB3_1_2)
8Microphone (Pink) 17 Clear CMOS Button
9 Optical SPDIF Out Port
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
Dedicated IPMI LAN Port LED Indications
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M bps connection or no
link
Blinking Yellow Data Activity Yellow 100M bps connection
On Link Green 1G bps connection
ACT/LINK LED
SPEED LED
LAN Port
4 6
16 11 1012
2
1
89
14 13
5 7
3
17 15

English
12
*** If you use a 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below
for connection details in accordance with the type of speaker you use.
Audio Output
Channels
Front Speaker
(No. 7)
Rear Speaker
(No. 5)
Central
(No. 4)
Line In
(No. 6)
2V -- -- --
4V V -- --
6V V V --
8V V V V
**** Please choose regular mini DisplayPort to DisplayPort adapter cables instead of right angled ones when you
use two mini DisplayPort input ports simultaneously.
*****Ultra USB Power is supported on USB31_1_2 ports. ACPI wake-up function is not supported on USB31_1_2
ports.
**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port
LED indications.
10G LAN Port (LAN1, LAN_2) LED Indications
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 100Mbps connection or
no link
Blinking Green Data Activity Yellow 5Gbps/2.5Gbps/1Gbps
connection
On Link Green 10Gbps connection
LAN Ports
ACT/LINK LED SPEED LED
ACT/LINK LED SPEED LED