ASROCK IMB-X1316 Service manual

IMB-X1316
Jumpers and Headers Setting Guide
The terms HDMI® and HDMI High-Denition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
DDR5_A1 (64 bit, 288-pin module) DDR5_B2 (64 bit, 288-pin module)
PSU_SMB1
ATXPWR1
1
1
1
PWR_COM6
PWR_COM5
1
PWRB TN PLED
RESET HDLED
11
1
PANEL1
COM5 COM6
1
SIM1
1
1
11
M2_M1
M2_E1
M2_M2
M2_B1
1
SATA3_6
SATA3_7
SATA3_4
SATA3_5
1
BLT_PWM2
BLT_PWM1
111
1
CLRMOS1
1
TB1
1
1
11
SATA3_1
SATA3_0
SATA3_3
SATA3_2
1
USB2_12_13
1
CPU_FAN1
1
CHA_FAN3
1
CHA 1_FAN
1
ATX12V1
CHA_FAN2
1
1
From left to right:
PWR_COM2
PWR_COM3
PWR_COM4
COM2 COM3 COM4
111
1
LPT_GPIO1
PCIE3
PCIE2
PCIE1
PCIE4
1
HEATER1
CI1CI2
DACC1
SIO_AT1
1
SPDIF1JGPIO_SET1
1
1
11
1
PS2_KB_MS1
JGPIO_PWR1
1
1
HD_AUDIO1
1
LAN2_LED1
1
BUZZ2
1
PWR_BAT1
1
SPEAKER1
1
Top:
LINE IN
Middle:
LINE OUT
Bottom:
MIC IN
1
IMB-X1316
Industrial
PWR_LOSS1
1
LAN_LED11
1
11
1
PWR_COM1
13 24 567
8910
11
12
13
14
15
16
19
18
17
20
21
22
23
24
25
26
2728
29
303133 32
34
35
3637
38
39
40
4142
43
44
45
46
48
49
USB 3.2 Gen2
: USB3_2Top
Bottom: USB3_1
Top:
LAN2
Middle:
USB 3.2 Gen2
USB3_9
USB2.0
Top:
USB2_10
iddle:M
USB2_11
HDMI2
Top:
LAN1
USB 3.2 Gen2
iddle: USB3_4M
Bottom: USB3_3
BKT_PWR 1
BLT_ VO L1
BLT_PWR1
PNL_PWR1
1
CMOS
Battery
50
51
52
53
55
54
COM1
HDMI1
DP1
Bottom:
USB 3.2 Gen2 x2 20G
Type C
TC_U3_7_8
DDR5_A2 (64 bit, 288-pin module)
DDR5_B1 (64 bit, 288-pin module)
BIOS
ROM
47
USB3_10
USB_53
1
1
ESPI1
1
LVDS1
1
Revision History
14 : System Panel Header (PANEL1)
8 : M.2 Key-M Socket
(M2_M1)
6 : M.2 Key-E Socket
(M2_E1)
Pin Signal Name Signal Name Pin
1 GND +3VSB 2
3USB_D+ +3VSB 4
5USB_D- NA 6
7 GND NA 8
9CNV_WGR_D1- CNV_RF_RESET 10
11 CNV_WGR_D1+ NA 12
13 GND MODEM_CLKREQ 14
15 CNV_WGR_D0- NA 16
17 CNV_WGR_D0+ GND 18
19 GND NA 20
21 CNV_WGR_CLK- CNV_BRI_RSP 22
23 CNV_WGR_CLK+
33 GND CNV_BGI_DT 32
35 PETp CNV_RGI_RSP 34
37 PETn CNV_BRI_DT 36
39 GND NA 38
41 PERp NA 40
43 PERn NA 42
45 GND NA 44
47 PEFCLKp NA 46
49 PEFCLKn NA 48
51 GND SUSCLK 50
53 CLKREQ# PERST0# 52
55 WAKE# W_DISABLE1# 54
57 GND W_DISABLE2# 56
59 CNV_WT_D1- SMB_DATA 58
61 CNV_WT_D1+ SMB_CLK 60
63 GND NA 62
65 CNV_WT_D0- CLKIN_XTAL_LCP 64
67 CNV_WT_D0+ NA 66
69 GND NA 68
71 CNV_WT_CLK- NA 70
73 CNV_WT_CLK+ +3VSB 72
75 GND +3VSB 74
Pin Signal Name Signal Name Pin
1 GND +3.3V 2
3 GND +3.3V 4
5PERn3 NA 6
7PERp3 NA 8
9 GND LED 10
11 PETn3 +3.3V 12
13 PETp3 +3.3V 14
15 GND +3.3V 16
17 PERn2 +3.3V 18
19 PERp2 NA 20
21 GND NA 22
23 PETn2 NA 24
25 PETp2 NA 26
27 GND NA 28
29 PERn1 NA 30
31 PERp1 NA 32
33 GND NA 34
35 PETn1 NA 36
37 PETp1 DEVSLP 38
39 GND SMB_CLK 40
41 PERn0 SMB_DATA 42
43 PERp0 NA 44
45 GND NA 46
47 PETn0 NA 48
49 PETP0 PERST# 50
51 GND CLKREQ# 52
53 PEFCLKn WAKE# 54
55 PEFCLKp NA 56
57 GND NA 58
67 NA NA 68
69 PEDET +3.3V 70
71 GND +3.3V 72
73 GND +3.3V 74
75 GND
12 : 24-pin ATX Power Input Connector
(ATXPWR1)
1
12
13
24
P Signal Name Signal Name Pin
1 HDLED+ PLED+ 2
3 HDLED- PLED- 4
5 GND PWRBTN# 6
7RESET# GND 8
9 GND 10
12
910
COM Port Headers
15 : COM5, COM6 (RS232)
34 : COM2 (RS232/422/485)*
COM3, COM4 (RS232)
Pin Signal Name Signal Name Pin
1DDCD# RRXD 2
3TTXD DDTR# 4
5 GND DDSR# 6
7RRTS# CCTS# 8
9PWR 10
12
910
Pin Signal Name Signal Name Pin
1 +3V +3V 13
2+3V -12V 14
3 GND GND 15
4 +5V PSON# 16
5 GND GND 17
6 +5V GND 18
7 GND GND 19
8PWROK_PS NA 20
9ATX+5VSB +5V 21
10 +12V +5V 22
11 +12V +5V 23
12 +3V GND 24
19 : LVDS Panel Connector (LVDS1)
• PD (Panel Detection):
Connect this pin to LVDS
Panel’s Ground pin to detect
Panel detection.
Pin Signal Name Signal Name Pin
1LCD_VCC LCD_VCC 2
3+3.3V N/A 4
5N/A LVDS_A_DATA0# 6
7LVDS_A_DATA0 PD (Panel Detection) 8
9LVDS_A_DATA1# LVDS_A_DATA1 10
11 GND LVDS_A_DATA2# 12
13 LVDS_A_DATA2 GND 14
15 LVDS_A_DATA3# LVDS_A_DATA3 16
17 GND LVDS_A_CLK# 18
19 LVDS_A_CLK GND 20
21 LVDS_B_DATA0# LVDS_B_DATA0 22
23 GND LVDS_B_DATA1# 24
25 LVDS_B_DATA1 GND 26
27 LVDS_B_DATA2# LVDS_B_DATA2 28
29 DPLVDD_EN LVDS_B_DATA3# 30
31 LVDS_B_DATA3 GND 32
33 LVDS_B_CLK# LVDS_B_CLK 34
35 GND CON_LBKLT_EN 36
37 CON_LBKLT_CTL LCD_BLT_VCC 38
39 LCD_BLT_VCC LCD_BLT_VCC 40
1
2
9
10
* This motherboard supports RS232/422/485 on COM1, 2 ports. Please refer to
the table below for the pin denition. In addition, COM1, 2 ports (RS232/422/485)
can be adjusted in BIOS setup utility > Advanced Screen > Super IO Congura-
tion. You may refer to our user manual for details.
Pin RS232 RS422 RS485
1 DCD TX- RTX-
2 RXD TX+ RTX+
3TXD RX+ N/A
4DTR RX- N/A
5 GND GND GND
6DSR N/A N/A
7RTS N/A N/A
8 CTS N/A N/A
9PWR PWR PWR
COM1, 2 Ports Pin Denition
9 : M.2 Key-M Socket
(M2_M2)
18 : M.2 Key-B Socket
(M2_B1)
Pin Signal Name Signal Name Pin
1 NA +3.3V 2
3 GND +3.3V 4
5 GND FuLL_Card_Power_o󰀨 6
7USB_D+ W_DISABLE 8
9USB_D- WWAN_LED# 10
11 GND
NA 20
21 GND NA 22
23 NA NA 24
25 NA NA 26
27 GND NA 28
29 USB3_RX- UIM_RESET 30
31 USB3_RX+ UIM_CLK 32
33 GND UIM_DATA 34
35 USB3_TX- UIM_PWR 36
37 USB3_TX+ NA 38
39 GND NA 40
41 PERn0 NA 42
43 PERp0 NA 44
45 GND NA 46
47 PETn0 NA 48
49 PETP0 PERST# 50
51 GND CLKREQ# 52
53 PEFCLKn WAKE# 54
55 PEFCLKp NA 56
57 GND NA 58
59 NA NA 60
61 NA NA 62
63 NA NA 64
65 NA NA 66
67 NA NA 68
69 NA +3.3V 70
71 GND +3.3V 72
73 GND +3.3V 74
75 NA
Pin Signal Name Signal Name Pin
1 GND +3.3V 2
3 GND +3.3V 4
5PERn3 NA 6
7PERp3 NA 8
9 GND LED 10
11 PETn3 +3.3V 12
13 PETp3 +3.3V 14
15 GND +3.3V 16
17 PERn2 +3.3V 18
19 PERp2 NA 20
21 GND NA 22
23 PETn2 NA 24
25 PETp2 NA 26
27 GND NA 28
29 PERn1 NA 30
31 PERp1 NA 32
33 GND NA 34
35 PETn1 NA 36
37 PETp1 DEVSLP 38
39 GND SMB_CLK 40
41 PERn0 SMB_DATA 42
43 PERp0 NA 44
45 GND NA 46
47 PETn0 NA 48
49 PETP0 PERST# 50
51 GND CLKREQ# 52
53 PEFCLKn WAKE# 54
55 PEFCLKp NA 56
57 GND NA 58
67 NA NA 68
69 PEDET +3.3V 70
71 GND +3.3V 72
73 GND +3.3V 74
75 GND
20 : Panel Power Select
(PNL_PWR1)
1-2 : +3V
2-3 : +5V
4-5 : +12V
1
5
7 : CPU FAN Connector (+12V) (CPU_FAN1)
10 : Power Loss Header (PWR_LOSS1)
Short : Power Loss
Open : No Power Loss
1
5
1
2
4 : 8-Pin ATX 12V Power Connector (ATX12V1)
1
4
5
8
Pin Signal Name
1 GND
2 +12V
3CPU_FAN_SPEED
4FAN_SPEED_CONTROL
11 : PSU_SMB1
Pin Signal Name
1SMB_CLK
2 SMB_DATA
3SMBALERT#
4 GND
5+3V
COM Port Pin9 PWR Setting Jumpers
(Items 1, 13, 35)
1 : PWR_COM1 (For COM Port1)
13 : PWR_COM5 (For COM Port5)
PWR_COM6 (For COM Port6)
35 : PWR_COM2 (For COM Port2)
PWR_COM3 (For COM Port3)
PWR_COM4 (For COM Port4)
1-2 : +5V
2-3 : +12V
2
12 3
LAN LED Headers (Items 2, 47)
2 : LAN1_LED1 (For LAN1 Port)
47 : LAN2_LED1 (For LAN2 Port)
Pin Signal Name
1 LILEDP
2 LED_LNK#_ACT
3LED_1000#
4LED_2500#
1 4
Chassis FAN Connectors (+12V)
(Items 3, 5, 33)
3 : CHA_FAN1
5 : CHA_FAN3
33 : CHA_FAN2
Pin Signal Name
1 GND
2 +12V
3CHA_FAN_SPEED
4FAN_SPEED_CONTROL
14
1
4
14
Pin Signal Name Signal Name Pin
1 GND ATX12V 5
2GND ATX12V 6
3 GND ATX12V 7
4 GND ATX12V 8
14
12 3
3
1
12
3940
Date Description
June 28, 2023 First Release
September 12, 2023 Second Release
USB 3.2 Gen2 Connectors (Type A)
16 : USB3_10
17 : USB3_5
Pin Signal Name
1USB_PWR
2 USB_D-
3USB_D+
4 GND
5SSRX-
6SSRX+
7 GND
8SSTX-
9SSTX+ 14
5
9
1
4
5
9
USB3_10
USB3_5

Installation of ROM Socket
• The yellow dot (Pin1) on the ROM
must be installed at pin1 position of the
socket (white arrow area).
• Make sure the white dot on the ROM
is installed outwards of the socket.
• For further details of how to install
ROM, please refer to ASRI website.
Warning: If the installation does not
follow as the picture, then it may
cause severe damage to chipset &
MB.
43 : DACC Jumper (DACC1)
Short : ACC
Open : No ACC
38 : Digital Input / Output Power Select
(JGPIO_SET1)
1-2 : +5V
2-3 : GND
41 : Digital Input / Output Power Select
(JGPIOPWR) (JGPIO_PWR1)
1-2 : +12V
2-3 : +5V
36 : Printer Port / GPIO Header (LPT_GPIO1)
Printer Port : GPIO :
Pin Signal Name Signal Name Pin
1STB# AFD# 2
3 SPD0 ERROR# 4
5 SPD1 PINIT# 6
7SPD2 SLIN# 8
9 SPD3 GND 10
11 SPD4 GND 12
13 SPD5 GND 14
15 SPD6 GND 16
17 SPD7 GND 18
19 ACK# GND 20
21 BUSY GND 22
23 PE GND 24
25 SLCT 26
Pin Signal Name Signal Name Pin
1 GPIO77 GPIO76 2
3 GPIO80 GPIO75 4
5 GPIO81 GPIO74 6
7GPIO82 GPIO73 8
9 GPIO83 JGPIOPWR 10
11 GPIO84 JGPIOPWR 12
13 GPIO85 GND 14
15 GPIO86 GND 16
17 GPIO87 GND 18
19 GPIO72 GND 20
21 GPIO71 GND 22
23 GPIO70 GND 24
25 NC 26
125
26
2
37 : Buzzer Header ( BUZZ2)
12
• Note: Auto clear CMOS when system boot improperly.
12
44 : SPDIF Header (SPDIF1)
1 4
48 : Front Panel Audio Header (HD_AUDIO1)
10
2
9
1
15
• If you want to use the printer port
function, please short pin4 and
pin5 on Digital Input / Output Power
Select (JGPIO_PWR1).
DDR5_A1 (64 bit, 288-pin module) DDR5_B2 (64 bit, 288-pin module)
PSU_SMB1
ATXPWR1
1
1
1
PWR_COM6
PWR_COM5
1
PWRB TN PLED
RESET HDLED
11
1
PANEL1
COM5 COM6
1
SIM1
1
1
11
M2_M1
M2_E1
M2_M2
M2_B1
1
SATA3_6
SATA3_7
SATA3_4
SATA3_5
1
BLT_PWM2
BLT_PWM1
111
1
CLRMOS1
1
TB1
1
1
11
SATA3_1
SATA3_0
SATA3_3
SATA3_2
1
USB2_12_13
1
CPU_FAN1
1
CHA_FAN3
1
CHA 1_FAN
1
ATX12V1
CHA_FAN2
1
1
From left to right:
PWR_COM2
PWR_COM3
PWR_COM4
COM2 COM3 COM4
111
1
LPT_GPIO1
PCIE3
PCIE2
PCIE1
PCIE4
1
HEATER1
CI1CI2
DACC1
SIO_AT1
1
SPDIF1JGPIO_SET1
1
1
11
1
PS2_KB_MS1
JGPIO_PWR1
1
1
HD_AUDIO1
1
LAN2_LED1
1
BUZZ2
1
PWR_BAT1
1
SPEAKER1
1
Top:
LINE IN
Middle:
LINE OUT
Bottom:
MIC IN
1
IMB-X1316
Industrial
PWR_LOSS1
1
LAN_LED11
1
11
1
PWR_COM1
13 24 567
8910
11
12
13
14
15
16
19
18
17
20
21
22
23
24
25
26
2728
29
303133 32
34
35
3637
38
39
40
4142
43
44
45
46
48
49
USB 3.2 Gen2
: USB3_2Top
Bottom: USB3_1
Top:
LAN2
Middle:
USB 3.2 Gen2
USB3_9
USB2.0
Top:
USB2_10
iddle:M
USB2_11
HDMI2
Top:
LAN1
USB 3.2 Gen2
iddle: USB3_4M
Bottom: USB3_3
BKT_PWR 1
BLT_ VO L1
BLT_PWR1
PNL_PWR1
1
CMOS
Battery
50
51
52
53
55
54
COM1
HDMI1
DP1
Bottom:
USB 3.2 Gen2 x2 20G
Type C
TC_U3_7_8
DDR5_A2 (64 bit, 288-pin module)
DDR5_B1 (64 bit, 288-pin module)
BIOS
ROM
47
USB3_10
USB_53
1
1
ESPI1
1
LVDS1
1
32 : USB 2.0 Header (USB2_12_13)
1
2
9
10
Pin Signal Name Signal Name Pin
1USB_PWR USB_PWR 2
3 P- P- 4
5 P+ P+ 6
7 GND GND 8
9DUMMY 10
12 3
Pin Signal Name
1 +5V
2
3SPDIF OUT
4 GND
40 : PS/2 Keyboard/Mouse Header
(PS2_KB_MS1)
1
2
7
8
Pin Signal Name Signal Name Pin
1 KBCLK +5V 2
3KBDATA +5V 4
5 MSDATA GND 6
7MSCLK GND 8
Pin Signal Name Signal Name Pin
1 MIC2_L GND 2
3MIC2_R 4
5OUT2_R MIC_RET 6
7J_SENSE 8
9OUT2_L OUT_RET 10
46: PWR_BAT1
Open : Normal
Short : Charge Battery 12
Pin Signal Name
1 +5V
2BUZZ
31 : Thunderbolt AIC Connector (TB1)
15
Pin Signal Name
1TB_FRC_PWR
2 TBCIO_PLUG_EVENT_R2
3SLP_S3#
4TBT_SLP_S5_S4#
5 GND
39 : ATX/AT Mode Jumper (SIO_AT1)
Short : AT Mode
Open : ATX Mode
12
42 : Chassis Intrusion Headers (CI1, CI2)
12
45 : HEATER Header (HEATER1)
12 3
Pin Signal Name
1Heater PWR
2GND
3 NCT
49 : 3W Audio Output Wafer (SPEAKER1)
Pin Signal Name
1 OUTLN
2OUTLP
3OUTRP
4OUTRN
1 4
50 : Audio Jacks
Blue - Line In
Green - Line Out
Pink - Mic In
51 : Top : USB 3.2 Gen2 Port (USB3_2)
Bottom : USB 3.2 Gen2 Port (USB3_1)
52 : Top : RJ45 LAN Port (LAN2)
Middle : USB 3.2 Gen2 Port (USB3_9)
Bottom : USB 3.2 Gen2 x2 20G Type C Port
(TC_U3_7_8)
53 : Top : USB 2.0 Port (USB2_10)
Middle : USB 2.0 Port (USB2_11)
Bottom : HDMI Port (HDMI2)
54 : Top : COM Port (COM1) (RS232/422/485)*
Bottom Left : HDMI Port (HDMI1)
Bottom Right : DisplayPort (DP1)
55 : Top : RJ45 LAN Port (LAN1)
Middle : USB 3.2 Gen2 Port (USB3_4)
Bottom : USB 3.2 Gen2 Port (USB3_5)
CI1 :
Open : Normal
Short : Active Case Open
CI2 :
Open : Active Case Open
Short : Normal
3-4 : +5V
4-5: GND
• Do not apply force to the actuator cover after ic inserted.
• Do not apply force to actuator cover when it is opening over 120
degree, Otherwise, the actuator cover may be broken.
Pin Signal Name
1 GND
2SATA-A+
3 SATA-A-
4 GND
5 SATA-B-
6 SATA-B+
7 GND
29 : SATA3 Connectors (SATA3_0~SATA3_4)
24 : Brightness Control Voltage Mode
(BLT_PWM2)
1-2: +3V (Default)
2-3: +5V
28 : Clear CMOS Header (CLRMOS1)
1-2 : Normal
2-3 : Clear CMOS
1
2
3
25 : SATA3 Connectors (SATA3_4, SATA3_5)
26 : SATA3 Connectors (SATA3_6, SATA3_7)
23 : Brightness Control Mode (BLT_PWM1)
1-2 : From eDP PWM to CON_LBKLT_CTL
2-3 : From LVDS PWM to CON_LBKLT_CTL
• Please set to 1-2 when adjusting brightness
by Brightness Control bar under OS.
• Please set to 2-3 when adjusting brightness by BLT_VOL1.
21 : Inverter Power Control Wafer (BLT_PWR1)
22 : Backlight Volume Control (BLT_VOL1)
Pin Signal Name
1GPIO_VOL_UP
2 GPIO_VOL_DW
3PWRDN
4BLT_UP
5BLT_DW
6 GND
7 GND
Pin Signal Name
1 GND
2GND
3CON_LBKLT_CTL
4CON_LBKLT_EN
5LCD_BLT_VCC
6LCD_BLT_VCC
123
123
1
7
17
SATA3_0 SATA3_2
1
7
17
SATA3_1 SATA3_3
27 : Backlight Power Select
(LCD_BLT_VCC) (BKT_PWR1)
1-2 : LCD_BLT_VCC : +5V
2-3 : LCD_BLT_VCC : +12V
1
2
3
• Only supported by chargeable battery.
1
7
1
6
30 : ESPI Header (ESPI1)
Pin Signal Name Signal Name Pin
1 GND ESPI_IO0 11
2 ESPI_CLK ESPI_IO1 12
3 GND ESPI_IO2 13
4ESPI_CS# ESPI_IO3 14
5ESPI_RESET# ALERT#1 15
6 GND +3VSB 16
7 +3V Internal use 17
8ESPI_CS#1 +5VSB 18
9PLTRST# ESPI_ALERT# 19
10 COM_RST# GND 20
1
20