Assa Abloy EMTEK EMPowered Motorized Smart Lock Upgrade... User manual

EMPowered™ Motorized Smart Lock Upgrade
- Connected by August
Deadbolt
Download and install
Home app

What’s in the box
ITEM NO. DESCRIPTION QTY.
1EMPower Unit 1
1a August Module 1
1b Battery Cover 1
1c AA Batteries 4
1d M4-0.7 x 8mm Machine Screws 3
1e Interior Escutcheon 1
1f #10-32 x 2-1/8” Machine Screws 2
1g Mounting Plate 1
2Deadbolt Latch 2-3/4” Backset 1
2Deadbolt Latch 2-3/8” Backset 1
ITEM NO. DESCRIPTION QTY.
3Deadbolt Screw Guide 1
4Deadbolt Trim 1
5Deadbolt Extension Collar 1
6Deadbolt Cylinder 1
7#8 x 3/4”Wood Screws 4
8Deadbolt Strike Plate 1
9Deadbolt Security Plate 1
10 #10 x 3”Wood Screws 2
11 August Connect 1
12 August DoorSenseTM 1
1b
78
10 9
1d 1e
1a
1f
1g
1c
1
2
3
56
4
711 12

3
Door Prep
Door Jamb Prep
21
4"
2-3/8"
or
2-3/4"
.
1" Dia
Edge
Bore
1"
2-1/8" Dia.
Bore
1/8” Deep
23
4"
1-1/8"

4
Install Latch
1
Note: Use only the
supplied latch for proper
functionality.
!

5
Install Lock Cylinder
Extension Collar
required for thin doors
2
Must use
screw guide
!

6
Remove Battery Cover
3
Loosen screw
on bottom to
remove cover.

7
Install Interior Mounting Plate
4

8
Check Interior Mounting Plate Alignment
5
Center tail piece in
mounting plate hole
before tightening.
!

9
Install Interior Escutcheon
6
Bolt must be in retracted
(unlocked) position
!

10
Testing Operation
7

11
Bolt must be in retracted
(unlocked) position
before installing batteries.
Install Batteries
8
!

12
Handing the Lock
9
To hand the lock, press
the button until you hear
one beep

13
Go to the August App to Complete
Installation
10
Set Up a Device - EMTEK SMART LOCK
SET UP MY FIRST DEVICE SET UP A LOCK
CONNECTED BY AUGUST
SET UP AN EMTEK
SMART LOCK

14
Installing DoorSenseTM with Connected by
August Locks - Surface Mount Option
DoorSenseTM
Cover
DoorSenseTM
Housing
Mounting
Tape
Mounting
Screws
1. Determine mounting location 1-1/2”
3-1/2”
1-1/2”
3-1/2”

15
Installing DoorSenseTM with Connected by
August Locks - Surface Mount Option
2. Attach mounting tape then screw into frame
3. Go to the August app to calibrate your Lock

16
Installing DoorSenseTM with Connected by
August Locks - Flush Mount Option
1. Remove magnet from housing and place DoorSenseTM Cap
onto the magnet
DoorSenseTM
Housing
DoorSenseTM
Cap

17
Installing DoorSenseTM with Connected by
August Locks - Flush Mount Option
2. Drill hole and Insert DoorSenseTM
3. Go to the August app to calibrate your Lock
3-1/2”
5/8” Diameter
1/2” Deep
3-1/2”

18
Go to the August App to Complete
Installation
Set Up a Connect Hub
GO TO MENU SET UP A DEVICE SET UP A CONNECT

19
Install Cover
11
Secure cover by tightening
screw on bottom.

20
Hardware Troubleshooting
Symptom
Door is binding
Bolt will not deadlock
Bolt does not extend
or
retract smoothly
• Check that door and frame are properly aligned and door is free swinging.
• Check hinges: They should not be loose or have excessive wear on
knuckles.
• Check for sucient clearance of the bolt within the strike-side jamb.
Correct this by increasing the depth of the pocket for the bolt.
• Check for misalignment of bolt and/or strike which may be preventing
bolt from properly entering the strike. With the door open, extend and
retract the bolt; if it is smooth, check the strike alignment.
• Bolt and strike are misaligned, see above.
• Check the backset of door relative to adjustments already made to bolt.
• Verify proper door preparation and re-bore holes that are too small or
misaligned.
• Verify bolt is installed with correct side up (Step 1)
Suggested Action
Cycle lock in both the locked and unlocked positions. If problems are found:
Denitions
Automatic Re-lock Time: After a successful code entry and the unit unlocks, it will automatically
re-lock after thirty (30) seconds.
Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of lock and
can be enabled or disabled in the August Home App.
Low Battery: Battery state is shown on smartphone app.
Privacy Mode: Privacy mode is disabled by default. Privacy mode is enabled/disabled in the August
Home App.
Shutdown Time: If the wrong code is entered ve (5) times, the keypad will ash for 60 seconds. The
lock will not allow operation for 60 seconds.
Volume Setting Mode: The volume setting is set to Low by default; otherwise it can be set to High or
Silent in the August Home App.