Assa Abloy 3090 Guide

Adams Rite Manufacturing Co.
260 Santa Fe Street
Pomona, CA 91767
Phone: [phone]
Fax: [phone]
www.adamsrite.com
This manual contains important operation, maintenance &
warranty information.
Save this manual for future reference
Owner’s Manual
& User’s guide
For Model 3090
eForce®150 Keyless Entry
eForce® 150 Keyless Entry

February 2012 2 80-0180-262 Rev. D
80-0180-262 Rev. D 27 February 2012
LIMITED WARRANTY
Adams Rite Manufacturing Co. (hereinafter ADAMS RITE) manufactures its
products in a manner to be free of defects. Should any defect of manufacture
(in material or workmanship) occur in its products, ADAMS RITE, upon prompt
notification and proof to its satisfaction that the product was defective in manu-
facture for the use intended by ADAMS RITE, will at its option, exchange the
product, repair the defect or refund the price charged by ADAMS RITE, FOB
factory based on the following schedule:
All mechanical products for five (5) years from the date of manufacture;
All electrical products (including EL and ED exit devices) for three (3)
years from the date of manufacture;
The RITE Door®for five (5) years from the date of manufacture;
UltraLine Electric Strikes for five (5) years from the date of manufacture.
Limitations and exclusions:
This is a limited warranty and is in lieu of all other warranties (including the im-
plied warranties of merchantability and fitness for use) and under no circum-
stances shall ADAMS RITE be liable for any incidental or consequential dam-
ages or losses.
This warranty covers products as outlined above manufactured from May 1,
2003 forward.
This warranty does not cover damages from such causes as abuse, accident,
neglect, fire or freight damage.

February 2012 26 80-0180-262 Rev. D
80-0180-262 Rev. D 3 February 2012
TABLE OF CONTENTS
eForce®150 General Information .......................................... 4
Programming Information ...................................................... 4
User Code Descriptions......................................................... 5
Features and Options ............................................................ 6
Programming Instructions...................................................... 8
Program Master Code....................................................... 8
Program Emergency Code................................................ 9
Program Supervisor Code............................................... 10
Program a Lockout Code ................................................ 10
Program a Passage Code ............................................... 11
Program Normal User Codes .......................................... 11
Program One Time User Codes ...................................... 12
Delete All User Codes..................................................... 13
Delete Emergency, Supervisor, Lockout,
Passage or a Single Normal User Code.......................... 13
Delete a Block of Normal User Codes............................. 13
Reset All Features to Default Values............................... 14
Set Audible Keypad Feedback ........................................ 14
Set Visual Keypad Feedback .......................................... 14
Set Number of Successive Invalid User Code
Entries Accepted............................................................. 15
Set the Error Lockout Time ............................................ 15
Set the Hold-Open Time.................................................. 15
Set Emergency Hold-Open Time..................................... 16
Replacing Batteries ............................................................. 17
Replacing Mortise Cylinder.................................................. 18
Trouble Shooting ................................................................. 21
eForce®150 User Log ......................................................... 22
Limited Warranty ................................................................. 27

February 2012 4 80-0180-262 Rev. D
EFORCE®150 GENERAL INFORMATION:
The Keypad (with numbers 0-9, [*] and [#]) is used for
programming. In normal operating mode, the [*] key is
used for the enter key after user code entry.
Each key press will flash the yellow LED and sound one
tone. Audible and visual keypad feedback can be dis-
abled. Refer to programming instructions.
The Master and Emergency Codes must be re-
programmed from the factory pre-set codes before user
codes may be entered. The factory preset Master and
Emergency codes (1234 & 4321) cannot be revised back
into the unit.
All codes need to be entered twice for validation during
programming. If the two entered codes do not match, the
eForce®150 will exit programming mode and the previ-
ous code will remain active.
Following a number of 5 successive invalid code entries,
the red LED will flash once and a tone will indicate that
the eForce®150 will no longer accept further entries for
15 sec. One tone per second will sound during this time.
Refer to programming instruction to change default set-
tings for successive invalid code entries and error lockout
time.
PROGRAMMING INFORMATION:
Programming mode:
To enter programming mode, press and hold the [#] key
until the yellow LED flashes three times. Release the [#]
key and the yellow LED will begin to flash continually.
You are now ready to start the programming sequence.
At the end of each programming step ending with the
enter [#] key, the green LED will flash twice and the
sounder will emit 2 tones to indicate that valid values
were accepted. At the end of the programming se-
quence, you can either wait 2 seconds for the device to
time out and return to normal operating mode, or you can
press the [*] key to exit programming mode.
Speed mode:
At the end of a programming sequence, press the [#] key
within 2-4 seconds to program additional codes. This
action initiates the “speed programming mode”, eliminat-
ing the need to re-enter the Master or Supervisor code.
80-0180-262 Rev. D 25 February 2012
eForce 150 User Log
Installation Date Door Decription
Location User Name Code Notes
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152

February 2012 24 80-0180-262 Rev. D
eForce 150 User Log
Installation Date Door Description
Location User Name Code Notes
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
80-0180-262 Rev. D 5 February 2012
In programming mode, press the [*] key at any time to exit this mode. Wait
2 seconds before entering any code. The red LED will flash and a tone will
indicate that the programming mode has been exited.
The programming mode will exit automatically if an invalid code is entered
during programming (indicated by a red LED flash and a tone). The pro-
gramming mode can be reinitiated by pressing the [#] key.
The eForce®150 will always return to the standard user mode after the
programming mode is exited.
User Code Descriptions:
Note: In user mode, entries must be followed by the [*] key
Master Code:
The default Master code setting (1234) must be changed before program-
ming additional user codes. In addition to using this code to program Emer-
gency and Supervisor codes, the Master code can be used to unlock the
device. The code must be between 4 and 7 digits.
Emergency Code:
The default Emergency code setting (4321) must also be changed prior to
programming the eForce®150 features and codes, though it is not used in
programming the eForce®150. This code unlocks the device in all condi-
tions, including a low battery condition or “blackout”. It will open the
eForce®150 for the preset time (10 sec. default). The code must be be-
tween 4 and 7 digits.
Supervisor Code:
The Supervisor code has no preset default, so it must be programmed by
the user if needed. It is used to unlock the eForce®150, even under low
battery conditions. It allows for programming every code except the Master
code, and is also required to delete codes. Normal and One Time user
codes (6-152) may be entirely deleted or partially deleted in a block . The
Emergency, Lockout, and Passage codes may be deleted singly rendering
these functions completely non-operational (they will not return to default
once deleted). The Supervisor code must be between 4 and 7 digits.
Lockout Code:
The Lockout code is used to restrict Normal User codes (6-152) from gain-
ing access. Entry of Lockout Mode is indicated by a green LED flash and
two tones, with a pause followed by two additional tones. Only the Master,
Emergency, and Supervisor codes can override the Lockout code. Entering
the Lockout code a second time will cancel the Lockout and allow access
with Normal User codes. Exit of Lockout Mode is indicated by a green LED
flash and two tones. The Lockout code must be between 4 and 7 digits.

February 2012 6 80-0180-262 Rev. D
Passage Code:
The Passage code is used to enable or disable the Passage mode. Enter-
ing the Passage code will cause the device to allow free ingress entry
(Passage enabled is indicated by a green LED flash and 3 tones). A sec-
ond entry of the Passage code will return the eForce 150 to the Normal
User Mode (exiting Passage Mode is indicated by a green LED flash and 2
tones). The Passage Mode operates when the battery is low and can be
overridden by the Lockout code. The code must be between 4 and 7 digits.
Normal User Codes:
Normal User codes are used to briefly unlock the device. A correct code
entry is indicated by a green LED flashing once per second. An incorrect
code entry is indicated by a red LED flash and 3 tones. Up to 144 different
Normal User codes may be programmed. These codes may not be pro-
grammed until after the default Master and Emergency codes have been re
-programmed. They must be between 2 and 7 digits.
One-Time User Codes:
One-Time user codes are used to unlock the device and are only valid for a
single operation of the eForce 150. A correct code entry is indicated by a
green LED flashing once per second. An incorrect code entry is indicated
by a red LED flash and 3 tones. Different One-Time user codes may be
programmed into locations 151 and 152. These codes may not be pro-
grammed until after the default Master and Emergency codes have been re
-programmed. They must be between 2 and 7 digits. After a One-Time user
code is used to operate the eForce®150, the same or a new code must be
programmed into the eForce®150 using the Master or Supervisor codes.
Features and Options:
Note: Program Command Codes (PCC) are designated codes for programming
and is always entered after the Master or Supervisor code during programming
mode.
Error Lockout: The eForce®150 will stop accepting key presses after 3 suc-
cessive invalid entries. Error Lockout is indicated by one red LED flash and 3
tones, followed by one tone per second for the duration of the Lockout time.
The eForce®150 will not accept any key presses during this preset (PCC 34)
time. The Error Lockout function overrides the horn disable function (PCC 31).
Low Battery Indicator: When the battery voltage drops below 4.0 volts, the
eForce®150 will emit 4 tones before allowing entry. If the battery voltage drops
below 3.8 volts, the eForce®150 will enter blackout mode, indicated by 4 tones
followed by 4 tones, and will not open. The eForce®150 will function for the
Master, Emergency, and Supervisor codes only. See “battery replacement”
instructions.
Piezo Sounder: This will emit a tone with each keystroke and varying tones to
indicate various conditions. The sounder can be disabled using the Master or
Supervisor code (PCC31).
80-0180-262 Rev. D 23 February 2012
eForce 150 User Log
Installation Date Door Description
Location User Name Code Notes
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76

February 2012 22 80-0180-262 Rev. D
eForce 150 User Log
Installation Date Door Description
Location User Name Code Notes
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
80-0180-262 Rev. D 7 February 2012
LED Indicator: All 3 LED’s can be disabled in User Mode by the Master or Su-
pervisor code (PCC32), but will remain enabled in programming mode. Yellow
indicates programming mode. Green indicates successful entry. Red indicates
input error. The LED’s will also flash to indicate various conditions.
Variable Re-lock time: The duration that the eForce®150 remains unlocked
can be adjusted (PCC 44) from 1 to 9 seconds. Default is 4 seconds.

February 2012 8 80-0180-262 Rev. D
Programming Instructions:
The eForce®150 can support 152 individual codes. Each code is assigned a
code location (1-152) in addition to a user name and the code’s programmed
digits. Program Command Code 51 is used for programming Master, Emer-
gency, Supervisor, Lockout, Passage, Normal, and One Time User codes.
The Master code is always code location number 1 and can be used to oper-
ate and program the eForce®150. Use the included record log to assign and
log all codes before proceeding on to programming. Store the log in a secure
location.
eFORCE®150 PROGRAMMING GUIDE:
FOLLOW STEPS 1 THROUGH 7
STEP 1: MASTER CODE (Quick Step Programming)
(Location 1)
Depress and hold # key (approximately 5 seconds).
Release when yellow LED blinks. (Yellow LED will blink continuously
during programming)
Enter 1234 # (Green flash with 2 short
tones)
Enter 51 # (Green flash with 2 short tones)
Enter 1 # (Green flash with 2 short tones)
Enter new Master Code # (4-7 digits) (Green flash with 2 short tones)
Re-Enter new Master Code # (Green flash with 2 short tones)
Green flash with 2 short tones will repeat to indicate successful code
programming
Press # within 2 seconds to stay in programming mode, and then
enter 51# to continue steps 2 through 7.
(Note* if Master Code is lost, the controller’s Master and Emergency
Codes may be reset to factory defaults (1234 and 4321 respectively). To
accomplish this task:
80-0180-262 Rev. D 21 February 2012
TROUBLE SHOOTING:
Green light comes on, but lever will not retract latch-bolt.
Check the eForce®150 body connection with lock/latch mechanism.
Check the cylinder tailpiece length (see installation instructions).
Check for proper door preparation (refer to door templates).
No lights come on when pushbuttons are depressed.
Ensure Visual Keypad Feedback is set to Enable (PCC32).
Check battery installation.
Check 6 Volt battery
Check keypad terminal connection.
No tones sound when pushbuttons are depressed.
Ensure Audible Keypad Feedback is set to Enable (PCC 31).
Check battery installation.
Check 6 Volt battery
Check keypad terminal connection.
Factory default codes not working.
Delete all users and reprogram default codes.
User codes not working.
Ensure Lockout code has not been entered.
Check battery power (operator may be in blackout mode). See above for
battery replacement.
Check eForce®150 body connection.
Operator stays unlocked.
Ensure Passage code has not been entered.
Check cylinder tailpiece length (see installation instructions).
Check eForce®150 body connection.

February 2012 20 80-0180-262 Rev. D
Place eForce®150 back on mounting bracket
and guide spindle into cam plug. (Fig 8).
Make sure that back surface of trim is flush
with door stile surface then secure with two
(2) #10-32 x 5/8 screw thru the inside bottom
of trim.
Reinstall the battery holder into the housing
and slide the battery cover into position and
tighten screw with allen key. (Fig 9)
Remove allen key. Turn key into the neutral
position and remove key from the cylinder.
Enter a known user code to ensure the
eForce®150 is functioning correctly.
Refer to Trouble Shooting section if eForce®
150 does not function properly.
(Fig 8)
(Fig 9)
80-0180-262 Rev. D 9 February 2012
MASTER CODE RESET
Depress and hold the reset button located on the backside of the eForce
150 on the printed circuit board (Note: eForce 150 must be removed from
the door to reset).
Depress and hold Reset Button and # Key
Release both when yellow LED blinks.
A green and red flash with tone will indicate a successful reset.
(Note: at this point the Master and Emergency Codes have been replaced with
the factory default codes (1234 & 4321), all other codes will remain intact. In
order to accomplish any additional programming of features and codes, the
Master and Emergency Codes must be changed from the defaults.)
STEP 2: EMERGENCY CODE (Location 2)
Depress and hold # key (approximately 5 seconds).
Release when yellow LED blinks. (Yellow LED will blink continuously
during programming)
Enter New Master Code # (Green flash with 2 short tones)
Enter 51 # (Green flash with 2 short tones)
Enter 2 # (Green flash with 2 short tones)
Enter desired Code # (4-7 digits) (Green flash with 2 short tones)
Re-Enter Code # (Green flash with 2 short tones)
Green flash with 2 short tones will repeat to indicate successful code pro-
gramming.
Press # within 2 seconds to stay in programming mode, then enter
51# to continue steps 3 through 7.
(Note: Emergency Code defaults to a 10 sec. unlock time [PCC 46#].)

February 2012 10 80-0180-262 Rev. D
STEP 3: SUPERVISOR CODE (Location 3)
Depress and hold # key (approximately 5 seconds).
Release when yellow LED blinks. (Yellow LED will blink continuously
during programming)
Enter Master Code# (Green flash with 2 short tones)
Enter 51 # (Green flash with 2 short tones)
Enter 3 # (Green flash with 2 short tones)
Enter desired Code # (4-7 digits) (Green flash with 2 short tones)
Re-Enter Code # (Green flash with 2 short tones)
Green flash with 2 short tones will repeat to indicate successful code
programming.
Press # within 2 seconds to stay in programming mode then enter 51#
to continue Steps 4 through 7.
STEP 4: LOCKOUT CODE (Location 4)
Depress and hold # key (approximately 5 seconds).
Release when yellow LED blinks. (Yellow LED will blink continuously
during programming)
Enter Master or Supervisor Code # (Green flash with 2 short tones)
Enter 51 # (Green flash with 2 short tones)
Enter 4 # (Green flash with 2 short tones)
Enter desired Code # (4-7 digits) (Green flash with 2 short tones)
Re-Enter Code # (Green flash with 2 short tones)
Green flash with 2 short tones will repeat to indicate successful code
programming.
Press # within 2 seconds to stay in programming mode then enter 51#
to continue Steps 5 through 7.
80-0180-262 Rev. D 19 February 2012
Remove Back Plate of eForce®150 with
Caution! There are wires attached to
housing and back plate.
Using a Phillip Head Screwdriver, remove
the (8) #10-32 x 5/8 screws on the back
of the eForce®150 and gently lift the back
plate off the housing. (Fig 6).
Remove cylinder with Locking Ring Tool
(P/N 22-0594) and replace with new cylin-
der and secure with locking ring. (Fig 7).
Gently place Back Plate back on housing
and secure with (8) #10-32 x 5/8 screws.
Do not use Dummy Cylinder!
(Fig 6)
(Fig 7)