Assa Abloy Corbin Russwin SE LP10 MP9800 Series User manual

Please read these instructions carefully to prevent missing important steps
For Technical Assistance call Corbin Russwin at 1-800-810-WIRE (9473)
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
Attention Installer
Installation Instructions
MP9800 Series Multi-Point Lock
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
HID and iCLASS are registered trademarks of HID Global Corporation.
Important: Improper installations may result in damage to the lock and void the factory warranty.
The accuracy of the door preparation is critical for proper functioning and security of this lock.
FM488 10/18

1) Warning
Table of Contents
Warning......................................................................................... 3
General Description...................................................................... 4
Hardware Specifications .............................................................. 4
Electronic Specifications.............................................................. 4
Wiring Diagrams........................................................................... 5
Parts Breakdown .......................................................................... 7
Installation Instructions ............................................................. 10
Concealed Door Position Switch Instructions ........................... 16
Operational Check ...................................................................... 17
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a parti-
cular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced technician for help
Contains FCC ID: U4A-SCSEHF
Contains IC: 6982A-SCSEHF
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. This Class B digital apparatus
meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est
sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence
reçue, y compris l’interférence qui peut causer l’opération peu désirée.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and Corbin Russwin Manufacturing makes
no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated ope-
ning, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure
compliance with all applicable codes and ratings.
This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.
For more information go to: www.P65warnings.ca.gov.
Ce produit peut vous exposer au plomb qui, dans l’état de la Californie, est reconnu pour causer le cancer, des anomalies congénitales ou
d’autres problèmes de reproduction.
Pour plus d’informations, visitez: www.P65warnings.ca.gov.
WARNING

4
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
The Corbin Russwin SE LP10 brings a new level of flexibility to our Integrated Wiegand access control solutions
for MP9800 series multipoint locks. Featuring multiCLASS SE® Technology from HID Global®, the SE LP10 is
ideal for mixed credential environments and enables easy migration to higher security credentials and mobile
access. SE LP10 multipoint locks include an external Door Position Switch (DPS) for door position monitoring
and other monitoring options, such as latchbolt and lever monitoring, are available as add-ons. The SE LP10
reader provides visual (LED) and audible indicators of lock state (locked/unlocked).
All SE LP10 Multi Point Locks
• Fire rated devices available
• Multi point lock furnished for 1-3/4” doors
• Fail safe or fail secure available
• Door Position Switch (708F989) supplied
for monitoring
• 24VDC motor-operated ET Trim available
• Wire from EAC Panel to door must be
shielded with a drain terminated at EAC
Panel controller
SE LP10 MP9800 Series Multi Point Lock
• Cylinder override available for MP9800 with
Auxiliary Control
Hardware Specifications
3
Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), CSA 22.1, Canadian Electrical
Code (CEC), Part I, Safety Standard for Electrical Installations, local codes, and the authorities having jurisdiction.
SE LP10 Non - MELR
12VDC / 24 VDC System (Non-MELR)
• Reader Draw = 150mA
• Actuator Draw = 400mA
• Total System Draw = 550mA
SE LP10 - MELR
12VDC System (MELR)
• Reader Draw = 200mA
(Reader is always 12VDC)
• 12VDC MELR Module Draw = 850mA
• Total System Draw = 1050mA
• Outside lever can be controlled by multiple credential formats:
• 2.4 GHz credential compatibility
• Secure Identity Object™(SIO) on Mobile IDs
(Bluetooth Smart)
• 13.56 MHz credential compatibility:
• Secure Identity Object™ (SIO) on iCLASS Seos,
iCLASS SE/SR, MIFARE DESFire EV1 and MIFARE Classic
(on by default)
• Standard iCLASS Access Control Application, ISO14443A
(MIFARE) CSN, ISO14443B CSN, and ISO15693 CSN
• ISO14443A/B (PIV-compatible Transparent FASC-N read)
available with SE LP10-F
• NFC-enabled mobile phones
• 125 kHz credential compatibilty:
• HID Prox®, AWID, EM4102
2) General Description
3) Hardware Specifications
4) Electronic Specifications

5
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
Total
One-Way
Length of
Wire Run (ft)
Load Current @ 12VDC
1/4A 1/2A 3/4A 1A 1-1/4A 1-1/2A 2A 3A
100 20 18 16 14 14 12 12 10
150 18 16 14 12 12 12 10 —
200 16 14 12 12 10 10 — —
250 16 14 12 10 10 10 — —
300 16 12 12 10 10 — — —
400 14 12 10 — — — — —
500 14 10 10 — — — — —
7501210——————
1,000 10 — — — — — — —
1,500 10 — — — — — — —
Wire Gauge Charts
Total
One-Way
Length of
Wire Run (ft)
Load Current @ 24VDC
1/4A 1/2A 3/4A 1A 1-1/4A 1-1/2A 2A 3A
100 24 20 18 18 16 16 14 12
150 22 18 16 16 14 14 12 10
200 20 18 16 14 14 12 12 10
250 18 16 14 14 12 12 12 10
300 18 16 14 12 12 12 10 —
400 18 14 12 12 10 10 — —
500 16 14 12 10 10 — — —
750 14 12 10 10 — — — —
1,000 14 10 10 — — — — —
1,500 12 10 — — — — — —
Strip 1/4”
Overlap wires as shown. Use heat gun to set wires.
*Diagrams on following pages
Default Operation Mode:
• Red LED ‘ON’ when powered.
• Presenting a 13.56 MHz or 125 kHz credential causes LED to briefly
turn green and then return to red state.
• Presenting a FIPS 201 PIV credential causes LED to turn amber as
credential is authenticated. Reader emits a short beep when
credential is successfully read. Reference *Diagram #1.
Optional Operation Mode:
Connect selected TAMPER wire from reader to ElectroLynx cable pin 8.
Note: For fire rated doors solder sleeve (P/N 52-1373) to be applied to
desired lead 2.5” from base of reader. See diagram for application.
Connect Yellow TAMPER wire from ElectroLynx cable to desired EAC panel
control line.
As appropriate, use configuration card to activate desired mode on reader.
PIN 8 (Yellow – TAMPER)
PIN 6 (Blue – RX COM)
PIN 2 (Red – Reader POS)
PIN 1 (Black – Reader NEG)
PIN 3 (White – Data 1)
PIN 5 (Orange – RX NO)
PIN 7 (Brown - EGND)
PIN 4 (Tan – DPS COM)
PIN 2 (Gray – Lock POS)
PIN 1 (Violet – Lock NEG)
PIN 3 (Pink – DPS NC)
Note: When Yellow TAMPER wire is tied directly into EAC panel relay, no AC signals should be applied on wire or door reader performance will be impacted.
8 PIN CONNECTOR 4 PIN CONNECTOR
1-Black 2-Red 3-White 4-Green 5-Orange 6-Blue 7-Brown 8-Yellow 1-Violet 2-Gray 3-Pink 4-Tan
12VDC
(Reader)
WIEGAND WIEGAND RX RX EGND TAMPER 12/24 VDC
(LOCK RELAY)
DPS
(NC)
DPS
(COM)
NEG POS DATA_1 DATA_0 NO COM EGND OPEN
COLLECTOR
NEG POS DPS DPS
The SE LP10 reader can be configured for various modes of LED and beeper operation. HID programming
cards are supported to configure the behavior for LED and beeper activity. Call 1-800-810-WIRE (9473) for
details. Along with the programming cards, the TAMPER wire can be connected within the panel and the
lock in order to enable some of the listed features.
Wire Gauge Charts
5) Wiring Diagrams
PIN 4 (Green – Data 0)

6
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
Green (NC)
White (C)
3287 Door
Position Switch
12 Conductor
ElectroLynx Harness
From McKinney
SE LP10
QC12 Electric
Hinge From
McKinney
Lock body
Power Supply
(By Others)
READER NEG - Black, 1
READER POS - Red, 2
DATA 1 - White, 3
DATA 0 - Green, 4
RX (NO) - Orange, 5
RX (COM) - Blue, 6
*EGND- Brown, 7
TAMPER - Yellow, 8
LOCK NEG - Violet, 9
LOCK POS - Gray, 10
Input
120 VAC
Not Used
Black (Hot)
White (Neutral)
Green (Gnd)
HNG
12/24VDC
- +
SE LP10
Requires 12VDC
(-)
(+)
12/24VDC
DATA 1
DPS
DPS
Use (NC) for
Fail Safe
Operation
(NO) Fail
Secure
Operation
Electronic
Access Control
Panel
(By Others)
Lock
Relay
DIAGRAM #1 – MODE 1: RED LED ‘ON’ WHEN POWERED
Standard Application Shown - For Alternative Applications Contact 1-800-810-WIRE (9473)
Reader Requires 5 to 16VDC Filtered and Regulated
*IMPORTANT: Pin 7 must be tied to earth ground in the access control panel.
Failure to follow proper ESD safe grounding procedures could lead to equipment failure.
DATA 0
RX (NO)
RX (COM)
Typical SE LP10 Application Diagram (12/24VDC System)
• Reader Draw = 150mA@12VDC / 24VDC
• Actuator Draw = 400mA inrush / 15mA continious @12VDC / 24VDC
• Total System Draw = 550mA @12VDC / 24VDC
12VDC System / 24VDC System

7
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
SE LP10 MP9800 Series
Tools Required
• Phillips screw driver (standard size)
• Slotted screw driver (standard size)
• #8-32 tap & tap drill
(for metal door applications)
• T10 Torx Driver
2
1
3A
5A
4
6
18
7
12
13
14 15 16 17
15
15
22
22
20
22
6) Parts Breakdown

8
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
8 PIN CONNECTOR 4 PIN CONNECTOR
1-Black 2-Red 3-White 4-Green 5-Orange 6-Blue 7-Brown 8-Yellow 1-Violet 2-Gray 3-Pink 4-Tan
12/24VDC
(Reader)
WIE-
GAND
WIE-
GAND
RX RX EGND LED 12/24 VDC
(LOCK RELAY)
DPS
(NC)
DPS
(COM)
NEG POS DATA_1 DATA_0 NO/NC COM REF.
*DIA-
GRAMS
REF.
*DIA-
GRAMS
NEG POS DPS DPS
2
6
5A
19
10
1
3A
4
7
23
22
Tools Required
• Phillips screw driver (standard size)
• Slotted screw driver (standard size)
• #8-32 tap & tap drill
(for metal door applications)
• T10 Torx Driver
SE LP10 MP9800 Series
12
13
14 15 16
22
22
20
6) Parts Breakdown (Continued)

9
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
ITEM PART # Description Req.
1 - WD/MD/AD Inside Trim Assembly 1
2 - Outside Trim Assembly 1
3A 764F488 MD/AD Inner Chassis Assembly
MD/AD Inner Chassis Assembly, Fire (12-)
764F508 MD/AD Monitoring Inner Chassis, Fire (53-/12-53-)
3B 764F498 WD Inner Chassis Assembly (Not shown) 1
764F518 WD Monitoring Inner Case (53-) (Not shown)
4 764F538 Bottom Case 1
5A - MD/AD Top Rod and Bolt Assembly 1
5B - WD Top Rod and Bolt Assembly (Not shown) 1
6 764F558 Top Case Assembly 1
7 - Bottom Rod and Bolt Assembly 1
8 766F942 Standard Plate (Rectangular) (Not shown) 2
766F352 Sculpted Plate (Optional) (Not shown) 1
9 764F548 WD Top Case Bracket (Not shown) 1
10 765F452 I/S MELR Escutcheon Assembly 1
11 764F577 Top Strike Pack (not shown)
764F587 Bottom Strike Pack, Fire (A/B) (M107) (not shown)
764F567 Top and Bottom Strike Pack, STD (not shown)
12 763F629 SE Reader Assembly - Black 1
763F649 FIPS SE Reader Assembly - Black (200 bit Wiegand output)
763F669 FIPS SE Reader Assembly - Black (75 bit Wiegand output)
763F809 BIPS SE Reader Assembly - Black (Bluetooth)
13 - SE Mounting Plate
14 763F809 Trim Bezel - Black 1
15 763F719 Fire Block Kit 1
16 764F319 Gasket (for non-fire-rated doors) 1
17 752F728 I/S Mounting Plate 1
18 765F44M I/S SE LP10 Escutcheon 1
19 765F849 MELR Assembly 1
20 764F62M MD/AD Screw Pack (not shown) 1
21 764F64M WD Screw Pack (not shown) 1
22 763F918 Screw Pack, SE Series 1
23 - MELR Mounting Hardware 1
24 763F738 WD Mounting Hardware (shown as Item 23) (not shown) 1
25 752F598 #3 - 48 x 1/8” Pan head Machine Screw (not shown) 4
SE LP10 MP9800 Series (Continued)
6) Parts Breakdown (Continued)

10
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
Fig. 1A
Fig. 2
Fig. 1B Metal Door Shown
1 Door Preparation
A. Verify Hand and Bevel of Door
B. Door Preparation
2 Rod and Inner Case Installation
1. Refer to instruction sheet FM438 for rod and inner
case installation on metal doors.
2. Refer to instruction sheet FM436 for rod and inner
case installation on wood doors.
• Check hand of door. The Multi-Point lock may be handed.
• Door should be fitted and hung
• Verify box label for size of the Multi-Point lock, function
and hand
• Change hand (if necessary)
Left Hand
Reverse
LHR Outside
Inside
Right Hand
Reverse
RHR
Prepare door according to appropriate template. If necessary,
refer to www.corbinrusswin.com.
• Metal door (MD/AD) FM438
- Template: T31242
• Wood door (WD) FM436
- Template: T31243
7) Installation Instructions

11
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
1. Position ET carefully onto the inside door surface
the inside of the door. Be careful not to pinch wire harness.
2. Mount inside trim lever using (2) # 1/4” -20 x 3” Philips oval head
machine screws. (Fig. 3B).
1. For exterior applications, use ET gasket (765F859) to seal ET
escutcheon and outside door surface (Fig. 3A).
2. Feed wire through the through hole and attach the outside exit
trim to the door.
A. Outside Trim
3 Install Outside Trim and Inside Trim
B. Inside Trim
Fig. 3A
Fig. 3B
Outside
of Door
Fig. 4A
Reader
Backplate
Fire
Shield
Fig. 4B
Gasket
(for exterior doors)
4 Install Reader Backplate and (Optional*) Fire Shield or Gasket
1. For fire-rated doors only, install reader backplate and fire shield to
door using two (2) #8-18 x 5/8” Phillips flat head self-drilling screws
(Fig. 4A).
2. For exterior doors, install reader backplate and gasket (Fig. 4B) using
two (2) #8-18 x 5/8” Phillips flat head self-drilling screws.
*For non-fire rated interior doors, no fire shield or gasket is required; simply
install backplate using two (2) #8-18 x 5/8” Phillips flat head self-drilling screws.

12
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
Torx
security
screw
Fig. 5C
Fig. 5B
1. Fit trim bezel around the reader. Ensure access hole in the bezel aligns with screw hole on
reader. The reader should be mounted so the holes face the bottom of door (Fig. 5B).
2. Align top of reader with top of backplate. Pivot reader down until seated.
Guide wires as needed to avoid pinching.
3. Secure the reader with (1) #6-32 x 3/8” Phillips or anti-tamper security torx screw to the
mounting plate (Fig. 5C).
5 Installation of SE LP10 Reader & Trim Bezel
Fig. 5A
Observe precautions for handling electrostatic sensitive devices.
!
Reader
Module
If the SE LP10 reader is installed with a module (Fig. 5A), make sure that the reader is
powered down when inserting/removing the module; i.e., do not “hot-plug” (remove/
insert while reader is powered) module as it may damage the reader.

13
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
Inside of Door
6A Inside Mounting Plate and Wire Connections (Non-MELR)
1. Attach mounting plate using (2) #8 x 1/2” self-drilingl screws (Fig. 6A).
2. Connect 6- and 2-pin connectors from device to 6- and 2-pin connectors on reader
harness (Fig. 6B, C).
3. Connect ElectroLynx 4- and 8-pin connectors from the door harness to (black) 4- and 8-pin
connectors of the SE LP10 harness (Fig. 6D).
NOTE: Neatly fold excess wires into remaining space to prevent pinching
wires when mounting inside escutcheon (Fig. 6E).
Fig. 6D
SE LP10
Harness
8-pin
ElectroLynx
4-pin
ElectroLynx
Fig. 6C
Fig. 6B
Fig. 6E
Inside of Door
Fig. 6A

14
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
6B Inside Mounting Plate and Wire Connections (MELR)
1. Install the upper left mounting screw, #8 - 32 x 5/8 Fillister for metal door or #8 x 5/8 self-drilling
Fillister for wood doors (Figure 6F).
Note: Leave the screw loose enough to slide the MELR assembly on.
2. Snake the wire through opening in MELR assembly.
3. Slide the mounting clip of the MELR assembly underneath the installed screw and tighten it to secure
the assembly in place.
Note: Be careful not to pinch or disconnect the wire located in that area.
4. Install the remaining three (3) mounting screws: 8-32 x 5/8 Fillister for metal doors or #8 x 5/8
self-tapping Fillister for wood doors.
5. Install two (2) #8 x 1/2” self-drill screws in the bottom-most pair of holes in the mounting plate (Fig. 6F).
6. Connect 6- and 2-pin connectors from device to 6- and 2-pin connectors on reader harness
(Fig. 6B, C in previous step).
7. Connect ElectroLynx 4- and 8-pin connectors from the door harness to (black) 4- and 8-pin
connectors of the SE LP10 harness (Fig. 6D in previous step).
Fig. 6F
Detail
(2) 1/4”
self-drilling
screws
(4) #8-32 x 5/8”
Fig. 6F

15
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
7 Fire Plate Installation and Earth Ground Connection
1. Remove lower left screw from mounting plate. Feed screw through green/yellow ground wire ring terminal.
Reinstall screw. Ensure that green/yellow wire points toward top of door in order to avoid interference
with escutcheon.
2. Fasten plate with two #8 x 1 1/4” Phillips pan head self-drilling screws.
Note: For non-fire rated doors, omit fire plate.
8A Position Inside Escutcheon & Wires (Non-MELR)
1. Carefully and neatly fold lock body wires onto themselves. ElectroLynx
connectors should be positioned side-by-side under the fire block plate.
Device connectors should be positioned side-by-side on top of the
ElectroLynx connectors.
2. Position inside escutcheon in order to ensure wires are not pinched.
Adjust wires as necessary to ensure they are clear of rear escutcheon.
Seat inside escutcheon against door.
Note: Be sure to cover, but not pinch wires when mounting escutcheon.
3. Insert two (2) #8-32 x 5/8” Phillips flat head escutcheon screws and thread
into mounting plate.
Inside of
Door
Fig. 7B
Fig. 7A
Fig. 8A
(Non-MELR)
(2) #8-32 x 5/8” Phillips
Flat Head Under-cut
Machine Screws
Inside of
Door

16
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
Door
Position
Switch
McKinney
Electric
Hinge
Green (NC)
White (C)
Wiegand Access
Control System
12VDC: Optional 24VDC
Lock Available
(Reader is always 12VDC)
8B Position Inside Escutcheon & Wires (MELR)
Fig. 8B (MELR)
1. Position escutcheon against door by
hooking the top edge on the top of the MELR
assembly. Verify that no wires are being pinched.
2. Mount inside escutcheon assembly to
plate using (1) #8-32 x 5/8" Phillips flat
head undercut machine screw (Figure 8B).
Machine
screw detail
8) Concealed Door Position Switch Instructions
1. Concealed Door Position Switch Model 708F989 is included with this product.
System integrator shall determine use and installation location.
2. Drill a 1" Diameter Hole for both the Magnet and the Switch. Both holes shall
be 1" Deep and for the Switch (if needed) drill a 1/4" hole for the wires.
3. Connect the common wire of the switch to the common input terminal of
the EAC.
4. Connect the normally open wire of the switch to the normally open input
terminal of the EAC.

17
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.
SE LP10 Integrated Wiegand
With and Without MELR Option (Electric Latch Retraction)
For devices without cylinders, go to step 3.
1. For devices with cylinders, insert key into cylinder and rotate.
2. The key will retract the latch and rods, the key should rotate freely.
3. Depress inside rail to retract latch and rods.
Note: Once electrical wiring has been successfully completed
according to proper application, complete the following step:
1. Turn power ON.
2. Verify LED located on reader is ON.
Red or Green depending on reader
configuration (See reader
LED Configuration).
3. Present proximity credential and verify
LED and sounder activity.
4. Verify valid card read at EAC Panel.
5. Verify system operation functions;
i.e., when prox credential is presented
to reader that the door unlocks.
Feature WT1 WT2
12 or 24VDC lock
voltage adjustable X X
Operates as Fail Safe or
Fail Secure X X
"Learn" mode allows
testing of specific cards
without programming at
the panel level
X X
Card reader data
integrity is validated
at test unit
X X
Displays detailed
Wiegand data, including
hexadecimal string and
total bits received
X
Displays measured end-
of-line resistor values
(if applicable)
X
The ASSA ABLOY Wiegand Test Unit verifies your installation in
the field. The test unit checks for proper wiring, card reader data
integrity, lock functionality including lock/unlock, door position
status, and request-to-exit (REX) status.
In addition, this tool provides product demonstration abilities to
highlight the product’s features and capabilities.
Wiegand Test Unit
9) Operational Check

Notes
18
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the
express written permission of Corbin Russwin, Inc. is prohibited.

Corbin Russwin
225 Episcopal Road
Berlin, CT 06037
Phone: [phone]
Fax: [phone]
corbinrusswin.com
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Corbin Russwin, Inc. is prohibited.
Patent pending and/or patent - www.assaabloydss.com/patents.
FM488
10/18