Ateis PENTON CAD Series User manual

CAD10/T
MOULDED SOUND PROJECTOR
Page 1/2
This weatherproof soundprojector oers a formally unbeatable
combination of design and processing. The specially treated, high-
quality housing with stylish shapes and compact dimensions is made
of ABS components with integrated UV resistance. The loudspeaker is
designed to be easy to mount thanks to the swivel-tilt U-bracket, and
is suitable for railway stations, car parks, shopping centers, sports elds,
etc. due to its weatherproof design.
CAD10T_datasheet_AE_en_vn1.0_web
Electrical
Rated power, watts 10
Tappings 100 volt line, watts 10/5/2.5/1.25
Transformer Impedance, ohms 100V 1k/2k/4k/8k
Tappings 70.7 volt line, watts 5/2.5/1.25/0.375
Driver impedance, ohms 8
Eective Frequency Range, Hz (BSEN60268-5) 120-18,000
S.P.L. @ 1m, 1watt, dB, Test Signal Bandwidth 100Hz-10kHz 90
S.P.L. @ Full power, Octave Bandwidth 100
Acoustic Power (dB-PWL@1 watt) 1k/2k Hz, dB 87/89
Dispersion at 1k/2k Hz, Degrees 180/120
Directivity Axial Q factor, 1k/2k Hz 2.5/5.8
Environmental
IP-rating 66
Min/Max amb temp -25°C to 70°C
Relative humidity ≤95%
Mechanical
Dimensions, front & depth, mm Ø 138x204
Net weight, kg 1.3
Colour/Finish White
Material ABS Plastic with UV inhibitor and Stainless
steel hardware
Mounting Aluminium U bracket
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]

Page 2/2CAD10T_datasheet_AE_en_vn1.0_web
Disclaimer: We reserve the right of changes and errors.
125 250 500 1k 2k 4k 8k
70
75
80
85
90
95
100
Effective Frequency Range CAD10/T 120Hz - 18,000Hz
speech octave band sensitivity
sensitivity (1W, 1m) dB
Frequency Hz
Average SPL 90dB
4W
2W
1W
0.5W
4W
2W
1W
0.5W
APC4T/ENC
*with capacitor
Circuit Diagram
Circuit Diagram
0359
17
INSTALLATION GUIDE
CAD10/T
10W RED
5W BLUE
2.5W ORANGE
1.25W YELLOW
100 V COMMON BLACK
30 30
145
25
ø138
0
45
ø135
174
185
26
ø116
ø
3 - 7
Side view
(unit: mm)
Front view
(unit: mm)
1) Drill the mounting location holes for the unit in line with the“U”bracket (2 holes 30 millimetres apart) in the surface where the loudspeaker is to be located.
2) Remove back lid of the unit (cable gland end) and connect input cable to the ceramic terminal block through the cable gland provided.
Important Note
Please ensure that the input cable is connected to the selected terminal inside the loudspeaker chamber and to no other connection, as the unused transformer
tappings must always be isolated from one another.
Example: CAD10/TC use the Black wire (common) and the red wire for 10 watt tapping.
Use the Black wire (common) and the Blue for 5 watt, etc.
3) Secure the cable gland tight, ensuring that all the rubber washers are in place for the xing screws.You will observe that around the inner section of the chamber where
the back lid was removed is a large rubber washer, please make sure that this is in-place when replacing the back lid.
4) Before putting 100 volt line through the units it is advisable to check the impedance of the circuit.
CAD10/T Circuit diagram 100V CommonCAD10/TCCircuit diagram 100V Common
Thermal Fuse
Connection
through
cable tail
Ceramic
terminal
block
Yellow
Orange
Blue
Red
1.25W
2.5W
5W
10W
1.25W
2.5W
5W
10W
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]