Ateis PENTON PMC4/T User manual

PMC4/T
MOULDED CABINET LOUDSPEAKER
Page 1/2
The moisture-proof surface-mounted loudspeaker PMC4/T is
made of ABS plastic. Supplied with a special impregnated chassis,it
is very good for use in area for wet rooms. Likewise, this speaker for
example, can be used outdoor by ships.
PMC4/T is ideal for speech and light background music. In
accordance with the British Standard 6840 , this speaker is suitable
for use in humid rooms and premises where frequent supercial
cleaning of the speakers is required.
PMC4T_datasheet_AE_en_vn1.0_web
Electrical
Rated power, Watts 4
Tappings 100 volt line, Watts 4/2/1/0.5
Transformer Impedance, Ohms 100V 2.5k/5k/10k/20k
Tappings 70.7 volt line, Watts 1.25/2.5/5/10k
Driver impedance, Ohms 8
Eective Frequency Range, Hz (BSEN60268-5) 220-11.000
S.P.L. @ 1m, 1watt, dB, Test Signal Bandwidth 100Hz-10kHz 91
S.P.L. @ Full power Octave Bandwidth, dB 97
Acoustic Power (dB-PWL@1 watt) 1k/2kHz, dB 87/91
Dispersion at 1k/2k Hz, Degrees 180/110
Directivity Axial Q factor, 1k/2kHz 2.2/5.1
Environmental
IP Rating 56
Min/Max amb temp -25°C to 70°C
Relative Humidity ≤95%
Mechanical
Dimensions, front & depth, mm 119x119x67.5
Net weight, kg 0.69
Colou/Finish White RAL9016
Material ABS Plastic with UV inhibitors
Mounting 4 x Screws
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]

125 250 500 1k 2k 4k 8k
70
75
80
85
90
95
100
Effective Frequency Range 220Hz - 11.000Hz
Sensitivity (1W, 1m) dB
Frequency Hz
Average SPL 91dB
Page 2/2PMC4T_datasheet_AE_en_vn1.0_web
Disclaimer: We reserve the right of changes and errors.
62
.
5
3.90 x 4
3
.
70
3.60
20.5
8.70
2.65
Rubber Seal
7
.
56
119
2.65
Rubber Seal
4W
2W
1W
0.5W
100V COMMON
INSTALLATION GUIDE
PMC4/T
119
85
85
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]
Front view
(unit: mm)
Rear view
(unit: mm)
Top view
(unit: mm)
Circuit Diagram
Frequency response
0359
17
1) On selecting the chosen position for the loudspeaker please ensure that cable
gland entries situated in the back box are in the position you require. (Either 2
x 2 at the top with one at either side or one at the top and bottom with two at
one side).
2) Oer the speaker to the wall or ceiling and mark through the mounting
holes as shown in the rear view drawing above with a sharp pencil the position
required for drilling. It is important that you use the holes situated within the
rubber seal.
3) Drill 2 holes in any chosen position and then t the back box including rubber
seal to the wall/at surface.
4) Cabling can now take place, connect the 100 volt line supply to your required
volume (via transformer tappings) as shown on the circuit diagram.
5) With the cable in place the speaker (shown in front view drawing) can be
screwed through the mounting holes into position.