Ateis PENTON MSH Series User manual

MSH30/T
MUSIC HORN LOUDSPEAKER
Page 1/2
This weatherproof plastic music horn loudspeaker is manufactured
from an ABS moulded, low smoke zero Halogen UL-94V0 Plastic
with UV inhibitors. Being non-corrosive and resistant to salt laden
air makes it is suitable for both indoor and outdoor use. It includes a
mounting bracket manufactured in stainless steel.
It combines a re-entrant horn with a high frequency driver. The
combination of both delivers a controlled coverage pattern with
clear speech and quality background music reproduction.
Supplied complete with cable gland, this unit is ideal grey, RAL7035,
however alternative nishes are available upon request.
Its rugged construction and quick and easy installation make it
ideally suited for such places as outdoor swimming pools, sports
stadiums, leisure centres and railway stations.
MSH30T_datasheet_AE_en_vn2.0_web
Electrical
Rated power, Watts 30
Tappings 100 Volt line, Watts 30/15/7.5/3.75
Transformer Impedance, Ohms 100 Volt 333/667/1.33k/2.66k
Tappings 70.7 Volt line, Watts 15/7.5/3.75/1.875
Driver impedance, Ohms 8
Eective Frequency Range, Hz (BSEN60268-5) 70-16.500
S.P.L. @ 1 m, 1 Watt, dB, Octave, 100 Hz-10 kHz 99
S.P.L. @ 1 m, Full power, dB, Octave, 100 Hz-10 kHz 114
Dispersion at 1k/2k Hz, Degrees 70/120 (horizontal), 110/110 (vertical)
Acoustic Power (dB-PWL @ 1 Watt) 1k/2k Hz, dB 91/94
Directivity Axial Q factor, 1k/2k Hz 8.5/6.5
Environmental
IP Rating 66
Min/Max amb temp -25°C to 70°C
Relative Humidity ≤95%
Mechanical
Dimensions, front & depth, mm 442 x 260 x 287.5
Net weight, kg 5.5
Colour (Unless Specied) Grey, RAL7035
Material ABS Plastic with UV inhibitors
Mounting Aluminium U bracket
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]

442
260
3
3 x 10
ø
334
Front view
(unit: mm)
125 250 500 1k 2k 4k 8k
75
80
85
90
95
100
105
Effective Frequency Range 70Hz - 16,500Hz
Sensitivity (1W, 1m) dB
Frequency Hz
Average SPL 99dB
Page 2/2MSH30T_datasheet_AE_en_vn2.0_web
Disclaimer: We reserve the right of changes and errors.
192
270
287.5
45
0
50
1 x PG9 Gland
100V COMMON
30W 15W
7.5W
3.75W
INSTALLATION GUIDE
MSH30/T
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]
Side view
(unit: mm)
1) Remove the back lid of the unit and connect input cable to the
ceramic terminal block through the cable gland provided.
2) On removing the back lid of the horn loudspeaker you will
observe a 5 way plastic terminal block that is connected to the 100
volt line transformer. Fit the 100 volt line input cable to the selected
volume (watts) that you require. For more information, look inside
the lid where you will nd a list of matching cable colours to watts,
from 30 watts down to 3.75watts.
To change the tapping select the appropriate colour (black is
always common) and connect accordingly.
3) On selecting the tapping required and wiring the same, secure
the cable gland tight into the back lid of the chamber.
4) Around the inner section of the chamber, where the back lid was
removed, a rubber gasket is located, please make sure that it is in
place when retting to avoid water penetration.
5) Drill the mounting location holes for the unit in line with the U
bracket (2 holes 60 mm apart) in the surface where the loudspeaker
is to be located. It is not necessary to use the central mounting
hole in the bracket unless the loudspeaker is located on a pole
mount clamp.
6) Mount the speaker in the required location specied by an
acoustic engineer.
7) Before putting a 100 volt line through the unit it is advisable to
check the impedance of the circuit.
Circuit Diagram
Frequency response
0359
17