Ateis PENTON RCS Series User manual

RCS 3/T
ROUND METAL CEILING LOUDSPEAKER MINIATURE
Page 1/2
The RCS range of ceiling loudspeakers have been carefully
designed to blend seamlessly in to any installation. These units are
stylish yet unobtrusive.
Made from a pressed steel epoxy coated chassis incorporating
a twin cone driver, which oers a wider frequency response
than a standard single cone, this gives the RCS range a superior
performance. Designed to make installation quick and easy
and suitable for use in applications where background music
and speech are the primary requirement such as shops, schools,
restaurants, hotels, public houses, oces etc.
RCS3T_datasheet_AE_en_vn1.0_web
Electrical
Rated power, Watts 6
Tappings 100 volt line, Watts 6/4/2
Transformer Impedance, Ohms 100V 1.67k/2.5k/5k
Tappings 70.7 volt line, Watts 3/2/1
Driver impedance, Ohms 8
Eective Frequency Range, Hz (BSEN60268-5) 100-20.000
S.P.L. @ 1m, 1 watt, dB, Test Signal Bandwidth 100Hz-10 kHz 87
S.P.L. @ Full power Octave Bandwidth, dB 94
Acoustic Power (dB-PWL@1 watt) 1 k/2kHz, dB 83/85
Dispersion at 1k/2kHz, Degrees 180/180
Directivity Axial Q factor, 1 k/2kHz 2.0/2.4
Environmental
IP Rating 21
Min/Max amb temp -25°C to 70°C
Relative Humidity ≤60%
Mechanical
Dimensions, diameter, mm Ø104.5
Net weight, kg 0.49
Colour/Finish White RAL9016
Material Steel
Mounting Twin Spring
Cut-out, mm Ø85
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]

Page 2/2RCS3T_datasheet_AE_en_vn1.0_web
Disclaimer: We reserve the right of changes and errors.
INSTALLATION GUIDE
RCS 3/T
ATEÏS Europe B.V.
Celsiusstraat 1, 2652 XN Lansingerland, Netherlands
Phone [phone], www.ateis-europe.com, [email protected]
Circuit Diagram
0359
17
125 250 500 1k 2k 4k 8k
70
75
80
85
90
95
100
Effective Frequency Range 100Hz - 20KHz
Sensitivity (1W, 1m) dB
Frequency Hz
Average SPL 87dB
Side View Front View
COMMON BLACK
RED 6W
YELLOW 4W GREEN 2W
1) Cut an 85 mm diameter hole in the ceiling.
2) Selecting the required power tap (watts) by connecting the eld cable into the Terminal block as described in section 4.
3) Fit the speaker into the ceiling cutout by holding the mounting springs in an upwards position. Guide them through the cutout and
release. The speaker will then locate automatically.
4) You will nd on the top of the ceiling loudspeaker a 100 volt line transformer complete with ying leads and terminal Block, this is
were you connect your 100v line speaker cable. Connect the negative speaker cable to the black wire (common) to one of the other free
terminals, selecting your chosen tapping as per the circuit diagram detailed below.
Frequency response
85
Ø85
( Cutout )
Ø
104.5
Ø
78
Front view
(unit: mm)
Front view
(unit: mm)
Side view
(unit: mm)
Side view
(unit: mm)