Atlas Copco ETP STB34-12-I06 Instruction sheet

ETP STB34-12-I06
Printed Matter No. 9839 1892 01 Battery-Powered Nutrunner
Publication Date 2020-07-17
Valid from Serial No. A1820001 Product Instructions
ETP STB34-12-I06
(4-12 Nm)
8433302395
WARNING
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference

2© Atlas Copco Industrial Technique AB - 9839 1892 01
Table of Contents
Product Information................................................................................................3
General Information ..........................................................................................3
Safety Signal Words ..............................................................................3
Warranty ................................................................................................3
Website..................................................................................................3
ServAid ..................................................................................................4
Safety Data Sheets MSDS/SDS............................................................4
Product Safety Video for Nutrunners.....................................................4
Country of Origin ...................................................................................4
Dimensional Drawings...........................................................................4
Overview...........................................................................................................4
Technical Product Data .........................................................................4
Service Overview..............................................................................................5
Service Recommendations....................................................................5
Installation ...............................................................................................................6
Installation Requirements .................................................................................6
Installation .............................................................................................6
Installation Instructions .....................................................................................6
Wireless Communication.......................................................................6
Attaching and Removing the Battery .....................................................6
Operation .................................................................................................................7
Ergonomic Guidelines.......................................................................................7
Operating Instructions.......................................................................................7
LED Indicator (HMI)...............................................................................7
Tightening..............................................................................................8
Service .....................................................................................................................9
Preventing ESD Problems ................................................................................9
Maintenance Instructions..................................................................................9
Service Recommendations....................................................................9
Preventive Maintenance ........................................................................9
Lubrication Instructions.....................................................................................9
Lubricating Guide ..................................................................................9
Lubrication ...........................................................................................10
Troubleshooting....................................................................................................11
Overheated Tool .............................................................................................11
Recycling ...............................................................................................................12
Environmental Regulations.............................................................................12
Recycling Instruction.......................................................................................12

ETP STB34-12-I06 EN Product Information
© Atlas Copco Industrial Technique AB - 9839 1892 01 3
Product Information
General Information
WARNING Risk of Property Damage or Severe Injury
Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow
all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.
►Read all Safety Information delivered together with the different parts of the system.
►Read all Product Instructions for installation, operation and maintenance of the different parts of
the system.
►Read all locally legislated safety regulations regarding the system and parts thereof.
►Save all Safety Information and instructions for future reference.
Safety Signal Words
The safety signal words Danger, Warning, Caution, and Notice have the following meanings:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or se-
rious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if
not avoided, could result in minor or moderate injury.
NOTICE NOTICE is used to address practices not related to personal injury.
Warranty
■Product warranty will expire 12 months after the product is first taken into use, but will in any case ex-
pire at the latest 13 months after delivery.
■Normal wear and tear on parts is not included within the warranty.
■Normal wear and tear is that which requires a part change or other adjustment/overhaul during
standard tools maintenance typical for that period (expressed in time, operation hours or other-
wise).
■The product warranty relies on the correct use, maintenance, and repair of the tool and its component
parts.
■Damage to parts that occurs as a result of inadequate maintenance or performed by parties other
than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the
warranty.
■To avoid damage or destruction of tool parts, service the tool according to the recommended mainte-
nance schedules and follow the correct instructions.
■Warranty repairs are only performed in Atlas Copco workshops or by Certified Service Partners.
Atlas Copco offers extended warranty and state of the art preventive maintenance through its ToolCover
contracts. For further information contact your local Service representative.
For electrical motors:
■Warranty will only apply when the electric motor has not been opened.
Website
Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on
the Atlas Copco website.
Please visit: www.atlascopco.com.

Product Information EN ETP STB34-12-I06
4© Atlas Copco Industrial Technique AB - 9839 1892 01
ServAid
ServAid is a portal that is continuously updated and contains Technical Information, such as:
■Regulatory and Safety Information
■Technical Data
■Installation, Operation and Service Instructions
■Spare Parts Lists
■Accessories
■Dimensional Drawings
Please visit: https://servaid.atlascopco.com.
For further Technical Information, please contact your local Atlas Copco representative.
Safety Data Sheets MSDS/SDS
The Safety Data Sheets describe the chemical products sold by Atlas Copco.
Please consult the Atlas Copco website for more information www.atlascopco.com/sds.
Product Safety Video for Nutrunners
Learn more about safety features on Atlas Copco nutrunners and what measures the operator has to take
for a safe operation. Click the link or scan the QR code below to view the video:
https://www.youtube.com/watch?v=FAh6yttvUpw
Country of Origin
For the Country of Origin, please refer to the information on the product label.
Dimensional Drawings
Dimensional Drawings can be found either in the Dimensional Drawings Archive, or on ServAid.
Please visit: http://webbox.atlascopco.com/webbox/dimdrw or https://servaid.atlascopco.com.
Overview
Technical Product Data
Technical Product Data can be found on either ServAid, or the Atlas Copco website.
Please visit: https://servaid.atlascopco.com or www.atlascopco.com.

ETP STB34-12-I06 EN Product Information
© Atlas Copco Industrial Technique AB - 9839 1892 01 5
Service Overview
Service Recommendations
Preventive maintenance is recommended at regular intervals. See the detailed information on preventive
maintenance. If the product is not working properly, take it out of service and inspect it.
If no detailed information about preventive maintenance is included, follow these general guide-
lines:
■Clean appropriate parts accurately
■Replace any defective or worn parts

Installation EN ETP STB34-12-I06
6© Atlas Copco Industrial Technique AB - 9839 1892 01
Installation
Installation Requirements
Installation
For installation guideline, see Power Focus 6000 Configuration manual.
Installation Instructions
Wireless Communication
This tool supports both WLAN 2.4 and 5 GHz (except AdHoc), as well as Bluetooth.
Multitool Bluetooth connection may cause connection interference and is not recommended. The configu-
ration of WLAN and Bluetooth is handled in Tools Talk Service 2.
Attaching and Removing the Battery
1. Attach the battery to the tool and make sure that it is fastened correctly. The battery can be attached
pointing forward or backward, to get the best accessibility and balance.
2. To remove the battery, press the button on the battery and push it out.

ETP STB34-12-I06 EN Operation
© Atlas Copco Industrial Technique AB - 9839 1892 01 7
Operation
Ergonomic Guidelines
Consider your workstation as you read through this list of general ergonomic guidelines to identify areas
for improvement in posture, component placement, or work environment.
■Take frequent breaks and change work positions frequently.
■Adapt the workstation area to your needs and the work task.
■Adjust for a convenient reach range by determining where parts and tools need to be located to
avoid static load.
■Use workstation equipment such as tables and chairs appropriate for the work task.
■Avoid work positions above shoulder level or with static holding during assembly operations.
■When working above shoulder level, reduce the load on the static muscles by lowering the weight
of the tool, using for example torque arms, hose reels or weight balancers. You can also reduce
the load on the static muscles by holding the tool close to the body.
■Take frequent breaks.
■Avoid extreme arm or wrist postures, particularly during operations requiring a degree of force.
■Adjust for a convenient field of vision that requires minimal eye and head movements.
■Use appropriate lighting for the work task.
■Select the appropriate tool for the work task.
■In noisy environments, use ear protection equipment.
■Use high-quality inserted tools and consumables to minimize exposure to excessive levels of vibra-
tion.
■Minimize exposure to reaction forces.
■When cutting:
A cut-off wheel can get stuck if the cut-off wheel is bent or not guided properly. Use the correct
flange for the cut-off wheel and avoid bending the cut-off wheel during operation.
■When drilling:
The drill might stall when the drill bit breaks through. Use support handles if the stall torque is high.
The safety standard ISO11148 part 3 recommends using a device to absorb a reaction torque
above 10 Nm for pistol grip tools and 4 Nm for straight tools.
■When using direct-driven screwdrivers or nutrunners:
Reaction forces depend on the tool settings and joint characteristics. Strength and posture deter-
mine the amount of reaction force that an operator can tolerate. Adapt the torque setting to the op-
erator's strength and posture and use a torque arm or reaction bar if the torque is too high.
■In dusty environments, use a dust extraction system or wear a mouth protection mask.
Operating Instructions
LED Indicator (HMI)
LED Indicator Description
Connection Indicates the connection to the paired controller or
software system.
Batch Indicates when Batch done.
Battery Indicates battery status (flashing light = low battery,
constant light = empty battery).
Alarm A failure or event is detected.

Operation EN ETP STB34-12-I06
8© Atlas Copco Industrial Technique AB - 9839 1892 01
Tightening
As tightening torque increase the reaction force build up equally. Make sure that the tool is in correct work-
ing order and that the controller is correctly programmed. By doing this you avoid unexpected behavior
from the tool, which may result in operator injury.
Rotation Direction for the Tightening
Check that the tool is in the correct running direction by turning the reverse button or reverse ring :
Pistol Grip Models (with side buttons)
■Press in the reverse switch on the right hand side of the tool, to set the direction clockwise (CW).
■Press in the reverse switch on the left hand side of the tool, to set the direction counter clockwise
(CCW).
Pistol Grip Models (without side buttons)
■Double press the function button on the top of the start trigger to shift the direction between clockwise
(CW) and counter clockwise (CCW).
Angle Models
■Turn the reverse ring to the right, to set the direction clockwise (CW).
■Turn the reverse ring to the left, to set the direction counter clockwise (CCW).
Soft Start
The soft start function facilitates the screwhead and thread to reach the snug level. The duration of the
soft start is adjustable.
For further information about tightening, see Power Focus 6000 Configuration manual.

ETP STB34-12-I06 EN Service
© Atlas Copco Industrial Technique AB - 9839 1892 01 9
Service
Preventing ESD Problems
The components inside the product and controller are sensitive to electrostatic discharge. To avoid future
malfunction, make sure that service and maintenance is carried out in an ESD approved work environ-
ment. The figure below shows an example of an appropriate service work station.
Maintenance Instructions
Service Recommendations
Preventive maintenance is recommended at regular intervals. See the detailed information on preventive
maintenance. If the product is not working properly, take it out of service and inspect it.
If no detailed information about preventive maintenance is included, follow these general guide-
lines:
■Clean appropriate parts accurately
■Replace any defective or worn parts
Preventive Maintenance
Maximize Battery Life
In order to maximize battery life, do not leave the battery connected to the tool you do not use it for sev-
eral days. The battery can discharge and go into “sleep mode” which will require a special wake-up charge
procedure. For further information, see instructions for multicharger, 4211542485.
Lubrication Instructions
Lubricating Guide
Brand Cable nut Gears
Molycote BR2 Plus
CRC Litium grease No. 3020
Brand Angle gears General purpose
Molycote Longterm 2 plus
Almagard LE 3751

Service EN ETP STB34-12-I06
10 © Atlas Copco Industrial Technique AB - 9839 1892 01
Lubrication
Lubricate gears and clutch with grease containing molybdenum disulphide (e.g. Molykote BR2 Plus). Lu-
bricate o-rings and threaded connections with grease before assembling.
For more information, see Spare Parts section in ServAid - https://servaid.atlascopco.com.

ETP STB34-12-I06 EN Troubleshooting
© Atlas Copco Industrial Technique AB - 9839 1892 01 11
Troubleshooting
Overheated Tool
The tool can handle any normal line jobs that an operator sustains with the proper adjustments.
The tool temperature can be influenced by the following parameters:
■short cycle time
■torque above rated
■too low speed
■very high prevailing torque
■very soft joints
■ambient temperature

Recycling EN ETP STB34-12-I06
12 © Atlas Copco Industrial Technique AB - 9839 1892 01
Recycling
Environmental Regulations
When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle
the components in accordance with local legislation.
Batteries shall be taken care of by your national battery recovery organization.
Recycling Instruction
Pos. Part Remarks Recycle as
1 Front part Metal, steel
2 Planetary gear Metal, steel
3 Motor module (with trans-
ducer, speaker module
and led flex card)
Electronic
4 Nut Metal, steel
5 Trigger button Metal, steel

ETP STB34-12-I06 EN Recycling
© Atlas Copco Industrial Technique AB - 9839 1892 01 13
Pos. Part Remarks Recycle as
6 Handle body PA6 GF30
7 Electronics module Electronic
8 Handle body Plastics, other, PA
9 Battery Battery, Li-Ion
10 Battery connector Plastics, other, PA
11 Back up battery Battery, Li-Ion
12 Radio module Electronic
13 Lid Plastics, other, PA
14 RBU board assembly Electronic

Original instructions
Atlas Copco Industrial
Technique AB
SE-10523 STOCKHOLM
Sweden
Telephone: [phone]
www.atlascopco.com
© Copyright 2020, Atlas Copco Industrial Technique AB. All rights reserved.
Any unauthorized use or copying of the contents or part thereof is prohibited.
This applies in particular to trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any damage or malfunction caused
by the use of unauthorized parts is not covered by Warranty or Product
Liability.
Out of respect to wildlife and nature, our technical literature is printed on
environmentally friendly paper.