Atlas Copco RTX-4 User manual

RTX-4
TORQUE CHART
This chart shows the correlation
between pump gauge psi reading
and torque output for your Rapid-Torc
RTX-4 hydraulic torque wrench.
PSI FT.LB.
1500 578
1600 617
1800 694
2000 771
2200 848
2400 925
2600 10 02
2800 1079
3000 11 5 7
3200 1234
3400 1 3 11
3600 1388
3800 1465
4000 1542
4200 1619
4400 1696
4600 1773
4800 1850
5000 1928
5200 2005
5400 2082
5600 2159
PSI FT.LB.
5800 2236
6000 2313
6200 2390
6400 2467
6600 2544
6800 2621
7000 2699
7200 2776
7400 2853
760 0 2930
7800 3007
8000 3084
8200 3161
8400 3238
8600 3315
8800 3392
9000 3470
9200 3547
9400 3624
9600 3701
9800 3778
10000 3855
BAR NM
104 784
110 836
124 941
138 1045
152 11 5 0
165 1254
179 1359
193 1463
207 1568
220 1673
234 1777
248 1882
262 1986
276 2091
290 2195
303 2300
317 2404
331 2509
345 2613
358 2718
372 2822
386 2927
BAR NM
400 3031
414 3136
427 3241
441 3345
455 3450
468 3554
482 3659
496 3763
510 3868
524 3972
538 4077
552 4181
565 4286
579 4390
593 4495
607 4599
620 4704
634 4809
648 4913
662 5018
676 5122
690 5227
2
Set the pressure on the pump that
corresponds to the torque value.
1Find the closest torque value for
your application, either in ft-lbs
or in Nm.
FOOT-POUNDS NEWTON-METERS
The above torque values are only applicable when using a calibrated RTX-4 hydraulic torque wrench powered by a 10,000 psi pump
fitted with a calibrated class 1 gauge.
RT-PTCen-RTX-4 Copyright Rapid-Torc®. Part of the Atlas Copco Group Revised October 2014

QUICK SETUP
GUIDE
Setting up your hydraulic torque wrench for use is easy.
Please read the included user manual and safety instruc-
tion booklet for additional guidelines.
1
FOUR BASIC STEPS TO OPERATE YOUR RTX-4
4
Scan the code to see a brief overview video on how to use the document or go to
rapidtorc.com/torque_setup
RT-PTCen-RTX-4 Copyright Rapid-Torc®. Part of the Atlas Copco Group Revised September 2014
Wear personal protec-
tive equipment, such as
eyeglasses and steel-toe
shoes.
1
2
3
SET PRESSURE
Make sure the hoses are
free of any defects. The
couplers are on pump
and the tool should be
securely connected.
Place tool on at surface.
Turn pump on. Cycle the
tool. Press the “ON’ but-
ton on the remote, hold
until tool clicks. Release,
wait for the tool to click.
Repeat the cycle. Ensure
there is no leak.
4
Use the torque conver-
sion chart to set the psi
for the torque you need.
Press the remote’s “ON”
button and slowly turn
the pressure regulator
clockwise to reach the
right pressure.
CYCLE YOUR TOOL
CONNECT HOSES
WEAR PPE
2
3