Atronic Harmony Upright User manual

www.atronic.com
Atronic Harmony™
Installation Manual
Rev. 1.6
June 2008

2
June 2008
Harmony™ Installation Manual
RELEASE INFO
Release Info:
Atronic Harmony™
Installation Manual
Rev. 1.6
June 2008
WARNING!
The Harmony™ / Hi(!)bility™ manual is intended to provide QUALIFIED TECHNICAL
PERSONNEL ONLY with the information necessary to routinely maintain, service, and
repair the Atronic Harmony™ cabinet and components. To avoid personal injury or
damage to the equipment, do not perform any serviceing other than that contained in
this manual.
Copyright Notice:
© 2008, Atronic. All rights reserved.
No part of this publication may be copied or distributed, transmitted, transcribed,
stored in a retrieval system, or translated into any human or computer language, in
any form or by any means, electronic, mechanical, magnetic, manual, or otherwise, or
disclosed to third parties without the express written permission obtained from a
properly authorized official of Atronic.
DISCLAIMER
Atronic makes no representation or warranties, express or implied, with respect to
this publication, or any product of Atronic, including but not limited to warranties of
merchantability or fitness for any particular purpose. Atronic reserves the right to
make changes, enhancements, revisions and alterations of any kind to this publication
or the product(s) it covers without obligation to notify any person, institution or
organization of such changes, enhancements, revisions and alterations.
TRADEMARKS
This document may contain trademarks of Atronic. All other brand and product names
are trademarks or registered trademarks of their respective companies.

3
June 2008
Harmony™ Installation Manual
Introduction
About this Manual
Scope, Target Audience, Included Software Releases ....
Related Publications ...................................................
Safety Instructions .........................................................
Machine Components .......................................................
Dimensions ......................................................................
Technical Data ................................................................
Machine Installation
Overview ..........................................................................
Machine Mounting ............................................................
Drilling Template ...............................................................
Replace Shipping Locks .....................................................
Prepare Coin Acceptor .......................................................
Prepare Hopper .................................................................
Check Connectors ..............................................................
Check Commboard Settings ................................................
Apply Power ......................................................................
Switch On .........................................................................
Basic Setup (Overview only) ..............................................
Tests ...............................................................................
Technical Support Telephone Numbers ..............................
4
5
7
10
12
14
16
17
18
19
20
20
20
20
21
21
22
23
24
CONTENT

4
June 2008
Harmony™ Installation Manual
ABOUT THIS MANUAL
Scope
This Installation Manual describes how to install an
Atronic Harmony™ gaming machines.
It describes how to mount the machine to a base
stand and relevant procedures to be carried out before
the machine can be put into operation. Further it
contains important safety instructions, technical data
and cabinet drawings.
Target Audience
We address qualified technical personnel, who are
involved in installation, setup and configuration of
Atronic gaming machines. With this user group we
assume that they are basically familiar with gaming
machinesand casino related terminology.
Please read this document and the contained safety
notes carefully before you start machine installation.
Included Software Releases
The installation procedures described in this manual
do not relate to a certain software version.
INTRODUCTION

5
June 2008
Harmony™ Installation Manual
ABOUT THIS MANUAL
Related Publications
More detailed information about Atronic Harmony™
gaming machines may be found in the following
publications:
Software Manuals
•Manual HI Software (C4.x.x.x STD)
•Manual HI Software (C5.x.x.x STD)
Operation Manuals
•Manual HAV Operating (C4.x.x.x STD)
•Manual HAV Operating (C5.x.x.x STD)
Spare Parts
•Manual HAV Parts Catalogue
Linked Gaming Products
•Manual [ product ] - Setup and Configuaration
for a particular linked gaming product, such as
Mystery Magic™, Hot Link™, etc.
Peripherals
(Coin- and bill acceptors, hopper, printer, etc.)
•See folder "Peripherals" on the Atronic Service
Manual CD.
Note: All mentioned manuals can be found on a CD-
ROM titled "Atronic Service Manual 2008"
If this manual did not came with this CD-ROM, please
ask Atronic Technical Service for a free copy of the
latest revision.
INTRODUCTION

6
June 2008
Harmony™ Installation Manual
- blank page -

7
June 2008
Harmony™ Installation Manual
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Note!
This installation module of the Harmony™Upright
includes only information relating to the installation
of the upright cabinet. For other machine or cabinet
types please refer to the relevant manuals.
Follow the safety precautions below
and on the next page, to ensure safe
operation.
Caution! High Voltage
Power cable must be disconnected from the main
power socket, so that the machine is free from
electrical current. The power switch is intended for
service purposes only.
Caution! Tipping Hazard
The machine must be fastened to an appropriate base,
to prevent tipping over. Use the Atronic Installation
Station (AIS) for machine mounting.
-> see also page 17-18.
Caution! Moving Parts
Make sure to disconnect the hopper, when working
on it.
Caution!
The machine must not be cleaned using a high
pressure cleaner or a vapor jet and must not be
installed or operated in areas where high pressure
cleaners or vapor jets are used. Use in dry conditions
only.
Continues on next page

8
June 2008
Harmony™ Installation Manual
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Further safety precautions during Installation,
Service and Maintenance
•The machine weight is approx. 125kg. Always use
appropiate equipment for transportation.
•Disconnect the power cable from the socket, befo-
re working at the machine.
•The machine may only be operated in dry conditi-
ons and must be connected to a grounded mains
power socket.
•Check that all connectors are seated correctly. Fal-
se connections can cause irreparable damage, not
covered by warranty.
•For power cable routing remove the knock-out pla-
te on the appropriate side of the cabinet. Edge-
protection must be mounted once the knock-out
plate has been removed.
•Only qualified service personnel should perform
repairs.
•Electronic assemblies should only be changed with
the power switched off.
•Use only original Atronic parts for replacement.
•Atronic commboard and mainboard
Danger of explosion if battery is incorrectly repla-
ced! Check for correct polarity and replace with
the same or equivalent type only!
•The machine must not be cleaned using a high
pressure cleaner or a vapor jet and must not be
installed or operated in areas where high pressu-
re cleaners or vapor jets are used. Use in dry con-
ditions only.
•Please refer to relevant Atronic service manuals
for further instructions on setup, operation and
maintenance.

9
June 2008
Harmony™ Installation Manual
- blank page -

10
June 2008
Harmony™ Installation Manual
MACHINE COMPONENTS
MACHINE COMPONENTS
Arch
Online System
Module (optional)
Voucher Printer
(optional)
Coin Entry
Functional
Button Panel
Main Door Lock
Jackpot Key Switch
Audit Key Switch
Hopper Drawer Lock
Bill Entry / Bill Decal
Hopper Drawer
Name Plate
Coin Bowl
Arm Rest
Button Panel
Loudspeakers
Player Tracking
System (optional)
Monitor
Top Glass
Mechanical Meters
Front Buttons
Feature Box
Toplight

11
June 2008
Harmony™ Installation Manual
MACHINE COMPONENTS
MACHINE COMPONENTS
Logicbox
Logicbox Door
Logicbox Lock
Reset Button
Service Button
Maindoor Switch
Coin Unit
Optic Boards
Coin Acceptor
Bill Acceptor
- Head
- Stacker
- Cashbox
Hopper Drawer Switch
Monitor
Button Board
Mechanical
Meters (Cover)
Power Supply
Power Switch
Bill Door Switch
Hopper
Mains Cable Mains Filter
Subwoofer Cabinet
Multimediaboard
Cover

12
June 2008
Harmony™ Installation Manual
MACHINE COMPONENTS
Logic Box
MACHINE COMPONENTS
Logicbox Switch
Backplane
Commboard
Mainboard
DVD-ROM Drive
Graphic Card
(VP11)
Release Lever for
Multimediaboard
Cover
Multimediaboard
Multimediaboard
Cover

13
June 2008
Harmony™ Installation Manual
DIMENSIONS
DIMENSIONS
1140 mm / 44.9”
1058 mm / 41.7”
1440 mm / 56.7” (with 2-stage candle)
542 mm / 21.3” 550 mm / 21.7”
580 mm / 22.8”
~ 476 mm / 18.7”
1493 mm / 58.8” (with 3-stage candle)
1140 mm / 44.9”
1058 mm / 41.7”
1514 mm / 59.6” (with 2-stage candle)
360 mm / 14.2” 550 mm / 21.7”
580 mm / 22.8”
~ 476 mm / 18.7”
1567 mm / 61.7” (with 3-stage candle)
542 mm / 21.3”
Inch values rounded to one decimal place.
Harmony™ Upright (HAV)
with optional topper
Harmony™ Upright (HAV)

14
June 2008
Harmony™ Installation Manual
Weight: approx. 100 kg (220.5 lbs)
Required Voltage: 100V to 240V AC,
50Hz / 60Hz,
use earthed power outlet
min. 6A / 115V, 3A / 230V
Power Consumption: Idle Mode: approx. 160 Watt,
0.7A / 230V
Payout Mode: approx. 230 Watt,
1A / 230V
Max. Power: approx. 350 Watt
(Without internal power outlets)
Power Supply
Secondary Voltage:+24V / 4.5A
+12V / 12A
-12V / 0.5A
+5V / 11A
+3.3V / 7A
Fuse Power Supply: T 8A / 250V (UL fuse)
Fuses Filterboard: F2 (+12 V) = T 6.3A / 250V (UL fuse)
F3 (+24 V) = T 4A / 250V (UL fuse)
Environmental Specifications
Operating Temperature: 0°C - 45°C
(32°F - 113°F)
Operating Humidity:0% to 85% (non condensing)
TECHNICAL DATA
TECHNICAL DATA

15
June 2008
Harmony™ Installation Manual
- blank page -

16
June 2008
Harmony™ Installation Manual
MACHINE INSTALLATION - OVERVIEW
This section should only be carried out by
qualified technical service personnel.
Review the list below and perform as needed.
Explanations are located on the following pages and
in additional manuals.
Inspect machines for transport damage. Any
transport damage should be noted and witnessed
by the freight forwarder. The manufacturer accepts
no responsibility for transport damage.
Check machines for the correct paytable, glasses,
hardware configuration and that software EPROMs
are correctly installed.
Prepare the base by drilling the mounting holes.
Use the Atronic drilling template for proper
mounting hole placement.
Place and mount the machine to the base, using
the Atronic Installation Station (see next page).
Thread the power cable into the base. Do not
connect power to the machine.
Replace shipping locks with casino specific locks.
Install and connect accounting system.
Check that all internal and external connections
are seated correctly.
Prepare coin acceptor and hopper.
Apply power to the machine.
Load paper into the printer.
Execute basic machine setup (Initial Setup)
Configure game.
Test bill and coin handling.
MACHINE INSTALLATION
Note:
Depending on machine
configuration or jurisdictional
requirements, additional tasks
may have to be carried out
before the machine can be put
into operation (e.g. acceptance
inspection, logicbox sealing,
etc.).

17
June 2008
Harmony™ Installation Manual
MACHINE INSTALLATION
Machine Mounting
Caution! Tipping Hazard
Do not operate the machine unless it has
been properly secured with an Atronic In-
stallation Station (AIS). The machine can
tip over, if it is not properly mounted to a
solid base.
1. Use the Atronic Installation Station (AIS) drilling
template, supplied by Atronic, to mark the holes
on the base before drilling. Make sure to leave min.
180mm (7.1") distance to the next machine or a
wall on both sides of the cabinet.
If the drilling template is not at hand, use the
drawing on the next page.
2. Drill four holes 10mm (3/8") for the AIS mounting
(drillings a) and one out of three holes 10mm (3/8")
for the machine securing bolt (drillings d) into the
base. It is not important which of the 3 holes for
the securing bolt is used, if at least one securing
bolt is mounted. If the base stand has braces or
struttings placed below one mounting hole, simply
use another one.
3. Drill or cut out one 55mm (2¼") hole for threading
the mains cable into the base (drilling b).
4. Cut out the 60 x 50 mm (3¼") coin drop recess
for into the base stand (recess c)
5. Secure the AIS to the base using 4 mounting bolts
and fasten with washer and wingnuts.
Make sure that the boltheads are completely
lowered into the counterbores of the AIS.
MACHINE INSTALLATION
bc
a
d

18
June 2008
Harmony™ Installation Manual
50
117.5
307.5
50
105.5
270.5
394
491
41.5
181
6060
55
60
50
357.5
541
Baseplate (AIS)
Cabinet
Footprint
550
Ø 10mm
Ø 10mm
(drill 1 out of 3 for securing bolt)
Backside
DRILLING TEMPLATE
MACHINE INSTALLATION
Make sure to leave min. 180mm (7.1") distance to the next machine or
a wall on both sides of the cabinet. Do not cover the ventilation slots
at the backside of the cabinet.

19
June 2008
Harmony™ Installation Manual
MACHINE INSTALLATION continued
Machine Mounting (continued)
6. Connect the toplight and mount as illustrated. Hold
the toplight at its lower ring, when you screw it
into the bayonet catch to avoid damaging the top-
light.
7. Make sure that the mains power cable is comple-
tely inside the machine and that hopper drawer
and maindoor are closed and locked.
Two forceful persons (one on each side) should lift
the machine and then slide it onto the AIS. The
baseplate of the machine will grasp into the gui-
des of the AIS. If available, use a lift truck.
Caution!
The machine weighs approx. 100 kg.
Make sure that the mains power cable is
completely inside the cabinet and not
threaded through the AC hole, before sliding
the machine onto the AIS! Otherwise the
cable will be damaged!
8. Use at least one securing bolt to secure the ma-
chine to the AIS and the base stand. Fix the bolt
with washer and wingnut.
It is not important which of the 3 holes is used, if
at least one securing bolt is mounted. If the base
stand has braces or struttings placed below one
mounting hole, simply use another one.
Replace shipping locks
Atronic machines are equipped with shipping locks
for easy commisioning. These locks have to be replaced
by casino specific locks to provide appropriate
security.
MACHINE INSTALLATION
Hold here

20
June 2008
Harmony™ Installation Manual
MACHINE INSTALLATION continued
Prepare Coin Acceptor (MC-16)
•Slide holder for reference coin rightwards, remove
(plastic) transport chip and replace it with appro-
priate reference coin.
•Check reference coin for proper (parallel) seating.
-> See manuals Peripherals / Coin Acceptor for details.
Prepare Hopper
The hopper high level switch detects the filling level
of the hopper by the weight of the coins. If the switch
is activated, further accepted coins are separated to
the drop box. The switching threshold can be altered
with an adjustment srew.
•Fill the hopper with that amount of coins/tokens at
which you want the switch to be activated.
•Adjust switching threshold with the adjustment
screw that operates the high level switch.
-> See manuals Peripherals / Hopper for details.
Check cables and connectors
Check that all connectors are seated correctly, prior
to first power up. False connections can cause irre-
parable damage, not covered by warranty.
Check Commboard Settings
The commboard DIP switches and rotary switches
configure SAS address, APL address, progressive
mode and SAS (dual) channel allocation.
Use the DIP switch tables within manual "Software /
Basic Setup" for a particular software version (e.g.
C5.1.x) to check or alter the commboard settings.
Then connect to the online system components.
MACHINE INSTALLATION
Commboard
Logicbox
Cover