AudioCodes Mediant 3000 TP-6310 Installation and operation manual

AudioCodes One Voice Operations Center
EMS, SEM and IP Phones Management
Performance Monitoring and
Alarm Guide
Mediant 3000 with TP-6310
Version 7.0
Document #: LTRT- 32111

Version 7.0 3 Performance Monitoring and Alarms
Performance Monitoring and Alarms Contents
Contents
1Introduction .........................................................................................................9
2Performance Monitoring Parameters ..............................................................13
2.1 Frame: DS3 Monitoring (History) ...........................................................14
2.1.1 Tab: DS3 Statistics.................................................................................14
2.2 Frame: DS3 Monitoring (Real-Time).......................................................15
2.2.1 Tab: DS3 Statistics.................................................................................15
2.3 Frame: Fiber Group Monitoring (Real-Time).........................................16
2.3.1 Tab: Fiber Group Statistics.....................................................................16
2.4 Frame: Gateway System Monitoring (Configuration)...........................17
2.4.1 Tab: System IP.......................................................................................17
2.4.2 Tab: VoP Call Statistics..........................................................................18
2.4.3 Tab: Common Control............................................................................20
2.4.4 Tab: MEGACO Control...........................................................................21
2.4.5 Tab: MGCP Control................................................................................23
2.4.6 Tab: SIP IP to Tel...................................................................................26
2.4.7Tab: SIP Tel to IP...................................................................................27
2.4.8 Tab: Trunk Statistics...............................................................................28
2.4.9 Tab: SRD Statistics................................................................................29
2.4.10 Tab: IP Group Statistics..........................................................................29
2.4.11 Tab: Trunk Group Statistics....................................................................30
2.5 Frame: Gateway System Monitoring (History)......................................31
2.5.1 Tab: System IP.......................................................................................31
2.5.2 Tab: VoP Call Statistics..........................................................................31
2.5.3 Tab: Common Control............................................................................34
2.5.4 Tab: MEGACO Control...........................................................................34
2.5.5 Tab: MGCP Control................................................................................37
2.5.6 Tab: SIP IP to Tel...................................................................................39
2.5.7 Tab: SIP Tel to IP...................................................................................40
2.6 Frame: Gateway System Monitoring (Real-Time).................................42
2.6.1 Tab: System IP.......................................................................................42
2.6.2 Tab: VoP Call Statistics..........................................................................43
2.6.3 Tab: Common Control............................................................................44
2.6.4 Tab: MEGACO Control...........................................................................44
2.6.5 Tab: MGCP Control................................................................................47
2.6.6 Tab: SIP IP to Tel...................................................................................49
2.6.7Tab: SIP Tel to IP...................................................................................51
2.7 Frame: IP Group Monitoring (History) ...................................................52
2.7.1 Tab: IP Group Statistics..........................................................................52
2.8 Frame: IP Group Monitoring (Real-Time)...............................................53
2.8.1 Tab: IP Group Statistics..........................................................................53
2.9 Frame: SRD Monitoring (History)...........................................................53
2.9.1 Tab: SRD Statistics................................................................................53
2.10 Frame: SRD Monitoring (Real-Time)......................................................54
2.10.1 Tab: SRD Statistics................................................................................54
2.11 Frame: System Monitoring SIP (Configuration)....................................54
2.11.1 Tab: System IP.......................................................................................54

Performance Monitoring and Alarms 4 Document #: LTRT-32111
Mediant 3000 with TP-6310
2.11.2 Tab: VoP Call Statistics..........................................................................55
2.11.3 Tab: Common Control............................................................................57
2.11.4 Tab: SIP IP to Tel...................................................................................58
2.11.5 Tab: SIP Tel to IP...................................................................................59
2.11.6 Tab: SRD Statistics................................................................................60
2.11.7 Tab: IP Group Statistics..........................................................................61
2.11.8 Tab: Trunk Group Statistics....................................................................62
2.12 Frame: Trunk Group Monitoring (History).............................................63
2.12.1 Tab: Trunk Group Statistics....................................................................63
2.13 Frame: Trunk Group Monitoring (Real-Time)........................................64
2.13.1 Tab: Trunk Group Statistics....................................................................64
2.14 Frame: Trunk Monitoring (History) ........................................................65
2.14.1 Tab: Trunk Performance.........................................................................65
2.15 Frame: Trunk Monitoring (Real-Time)....................................................66
2.15.1 Tab: Trunk Performance.........................................................................66
3Alarms................................................................................................................67
3.1 Standard Traps........................................................................................68
3.1.1 Cold Start...............................................................................................68
3.1.2 Link Down ..............................................................................................69
3.1.3 Link Up...................................................................................................70
3.1.4 Entity Configuration Change...................................................................71
3.1.5 Authentication Failure.............................................................................71
3.1.6 DS1 Line Status .....................................................................................72
3.1.7 DS3 Line Status.....................................................................................74
3.2 EMS Alarms..............................................................................................75
3.2.1 EMS Trap Receiver Binding Error ..........................................................75
3.2.2 GW Connection Alarm...........................................................................76
3.2.3 GW Mismatch Alarm .............................................................................77
3.2.4EMS Server Started ...............................................................................78
3.2.5 Disk Space Alarm...................................................................................79
3.2.6 Software Replaced.................................................................................79
3.2.7 Hardware Replaced................................................................................80
3.2.8HTTP/HTTPS Access Disabled..............................................................80
3.2.9 PM File Generated.................................................................................81
3.2.10 PM Polling Error.....................................................................................82
3.2.11 Cold Start Missed...................................................................................83
3.2.12 Security Alarm........................................................................................83
3.2.13 Security Event........................................................................................84
3.2.14 Topology Update Event..........................................................................84
3.2.15 Topology File Event................................................................................86
3.2.16 Synchronizing Alarms Event...................................................................87
3.2.17 Synchronizing Active Alarms Event........................................................88
3.2.18 License Key Alarm .................................................................................89
3.2.19 Alarm Supression Alarm.........................................................................89
3.2.20 EMS Keep Alive Alarm...........................................................................90
3.2.21 Pre-provisioning Alarm...........................................................................90
3.3 SEM Alarms..............................................................................................91
3.3.1 SEM – Failed Calls Alarm.......................................................................91
3.3.2 SEM – Voice Quality Alarm ....................................................................91

Version 7.0 5 Performance Monitoring and Alarms
Performance Monitoring and Alarms Contents
3.3.3 SEM – Average Call Duration Alarm.......................................................92
3.3.4 SEM – License Key Alarm......................................................................93
3.3.5 SEM – System Load Alarm ....................................................................93
3.3.6 SEM – Call Details Storage Level has Changed.....................................94
3.3.7 SEM – Time Synchronization Alarm.......................................................94
3.3.8 SEM AD Lync Connection Alarm............................................................95
3.3.9 SEM MS Lync AD Server Alarm.............................................................96
3.3.10 SEM Rule Bandwidth Alarm ...................................................................96
3.3.11 SEM Rule Max Concurrent Calls Alarm..................................................97
3.4 Device Alarms..........................................................................................98
3.4.1 Board Fatal Error....................................................................................98
3.4.2 Configuration Error.................................................................................98
3.4.3 Temperature Alarm ................................................................................99
3.4.4 Initialization Ended...............................................................................100
3.4.5 Board Resetting Following Software Reset...........................................100
3.4.6 Feature Key Related Error....................................................................101
3.4.7 Gateway Administrative State Changed ...............................................101
3.4.8 No Free Channels Available.................................................................102
3.4.9 Gatekeeper/Proxy not Found or Registration Failed.............................102
3.4.10 Ethernet Link Down Alarm....................................................................103
3.4.11 System Component Overloaded...........................................................104
3.4.12 Active Alarms Table Overflow...............................................................104
3.4.13 Operational State Change....................................................................105
3.4.14 Keep Alive Trap....................................................................................105
3.4.15 NAT Traversal Alarm............................................................................106
3.4.16 Threshold of Performance Monitored Object Exceeded........................107
3.4.17 HTTP Download Result........................................................................107
3.4.18 Fan Tray Alarm ....................................................................................108
3.4.19 Power Supply Alarm.............................................................................110
3.4.20 PEM Module Alarm ..............................................................................111
3.4.21 SA Module Missing Alarm ....................................................................112
3.4.22 HA System Fault Alarm........................................................................113
3.4.23 HA System Configuration Mismatch Alarm...........................................117
3.4.24 HA System Switch Over Alarm.............................................................118
3.4.25 User Input Alarm ..................................................................................119
3.4.26 D-Channel Status.................................................................................119
3.4.27 SONET Section LOF Alarm..................................................................120
3.4.28 SONET Section LOS Alarm..................................................................121
3.4.29 SONET Line AIS Alarm........................................................................122
3.4.30 SONET Line RDI Alarm........................................................................123
3.4.31 SONET/SDN IF Failure Alarm..............................................................124
3.4.32 Dial Plan File Replaced Trap................................................................125
3.4.33 Hitless Update Event............................................................................125
3.4.34 Trunk LOS Alarm..................................................................................127
3.4.35 Trunk LOF Alarm..................................................................................128
3.4.36 Trunk AIS Alarm...................................................................................129
3.4.37 Trunk RAI Alarm...................................................................................130
3.4.38 IPv6......................................................................................................131
3.4.39 TM Inconsistency .................................................................................132
3.4.40 TM Reference Status ...........................................................................133
3.4.41 TM Reference Change.........................................................................134
3.4.42 SAS Emergency Mode Alarm...............................................................134
3.4.43 SONET Path STS LOP Alarm ..............................................................135

Performance Monitoring and Alarms 6 Document #: LTRT-32111
Mediant 3000 with TP-6310
3.4.44 SONET Path STS AIS Alarm................................................................136
3.4.45 SONET Path STS RDI Alarm ...............................................................137
3.4.46 SONET Path Unequipped Alarm..........................................................138
3.4.47 SONET Path Signal Label Alarm..........................................................138
3.4.48 DS3 RAI Alarm.....................................................................................139
3.4.49 DS3 AIS Alarm.....................................................................................140
3.4.50 DS3 LOF Alarm....................................................................................140
3.4.51 DS3 LOS Alarm....................................................................................141
3.4.52 Software Upgrade Alarm......................................................................141
3.4.53 NTP Server Status Alarm.....................................................................142
3.4.54 LDAP Lost Connection.........................................................................143
3.4.55 [Event] SSH Connection Status............................................................144
3.4.56 OCSP Server Status Alarm..................................................................145
3.4.57 Media Process Overload Alarm............................................................145
3.4.58 NFAS Group Alarm ..............................................................................146
3.4.59 B Channel Alarm..................................................................................147
3.4.1 Certificate Expiry Notification................................................................148
3.4.2 Web User Access Disabled..................................................................149
3.4.3 Proxy Connection Lost .........................................................................150
3.4.4 Redundant Board Alarm.......................................................................151
3.4.5 IDS Policy Alarm ..................................................................................152
3.4.6 IDS Threshold Cross Notification..........................................................153
3.4.7 IDS Blacklist Notification.......................................................................154
3.4.8 Proxy Connectivity................................................................................155
3.4.1 Web User Activity Log Trap..................................................................156

Version 7.0 7 Performance Monitoring and Alarms
Performance Monitoring and Alarms Notices
Notice
This document describes the Performance Monitoring parameters and alarms for the Mediant
3000 product.
Information contained in this document is believed to be accurate and reliable at the time of
printing. However, due to ongoing product improvements and revisions, AudioCodes cannot
guarantee accuracy of printed material after the Date Published nor can it accept responsibility
for errors or omissions. Updates to this document and other documents can be viewed by
registered customers at http://www.audiocodes.com/downloads.
© 2014 AudioCodes Inc. All rights reserved
This document is subject to change without notice.
Date Published: June-17-2014
Trademarks
AudioCodes, AC, AudioCoded, Ardito, CTI2, CTI², CTI Squared, HD VoIP, HD VoIP
Sounds Better, InTouch, Mediant, MediaPack, NetCoder, Netrake, Nuera, Open
Solutions Network, OSN, Stretto, TrunkPack, VMAS, VoicePacketizer, VoIPerfect,
VoIPerfectHD, What’s Inside Matters, Your Gateway To VoIP and 3GX are
trademarks or registered trademarks of AudioCodes Limited. All other products or
trademarks are property of their respective owners.
WEEE EU Directive
Pursuant to the WEEE EU Directive, electronic and electrical waste must not be
disposed of with unsorted waste. Please contact your local recycling authority for
disposal of this product.
Customer Support
Customer technical support and services are provided by AudioCodes or by an
authorized AudioCodes Service Partner. For more information on how to buy technical
support for AudioCodes products and for contact information, please visit our Web site
at www.audiocodes.com/support.
Abbreviations and Terminology
Term Description
MG Refers to the Media Gateway.
'Frame' and 'Screen' Sometimes used interchangeably

Performance Monitoring and Alarms 8 Document #: LTRT-32111
Mediant 3000 with TP-6310
Related Documentation
Manual Name
Mediant 3000 User’s Manual
Element Management System (EMS) Server Installation, Operation and Maintenance Manual
Element Management System (EMS) Release Notes
Element Management System (EMS) Product Description
Element Management System (EMS) OAMP Integration Guide
Element Management System (EMS) User’s Manual
Session Experience Manager (SEM) User's Manual
IP Phone Management Server Administrator's Manual
Element Management System (EMS) Online Help
Documentation Feedback
AudioCodes continually strives to produce high quality documentation. If you have any
comments (suggestions or errors) regarding this document, please fill out the
Documentation Feedback form on our Web site at
http://www.audiocodes.com/downloads.

Version 7.0 9 Performance Monitoring and Alarms
Performance Monitoring and Alarms 1. Introduction
1 Introduction
This guide incorporates Performance Monitoring parameters and alarms for the
Mediant 3000 TP-6310 product.

Version 7.0 11 OAM Guide
Performance Monitoring and Alarms 1. Introduction
This page is intentionally left blank.

Version 7.0 13 Performance Monitoring and Alarms
Performance Monitoring and Alarms 2. Performance Monitoring Parameters
2 Performance Monitoring Parameters
Customers are often faced with a complex VoIP network with little or no information on
the status and capacities of each component in it. PM helps the system architect
design a better network. PM helps operators discover malfunctioning devices before
they start causing a problem on the production network.
The system provides two types of performance measurements:

Gauges: Gauges represent the current state of a PM parameter in the system.
Gauges, unlike counters, can decrease in value, and like counters, can increase.

Counters: Counters always increase in value and are cumulative. Counters,
unlike gauges, never decrease in value unless the system is reset. The counters
are then zeroed.
Performance measurements are available for the EMS or for a 3rd party performance
monitoring system through an SNMP interface. These measurements can be polled at
scheduled intervals by an external poller or utility in a media server or another off-
device system.
PM measurements can be divided into two main groups:

Real-Time PM Measurements - supply the current value of the PM entity. When
requested, the entity is sampled and the current value is received.

History PM Measurements - supply statistical data of the PM entity during the last
interval period. These measurements include the Average, Minimum and
Maximum values of the entity during the last interval. The default interval length is
15 minutes.
Figure 1: History PM Measurements
History Performance is measured in a constant time interval of 15 minutes to which all
elements in the network are synchronized. Intervals commence precisely every 15
minutes, for example, 12:00:00, 12:15:00, 12:30:00, 12:45:00, etc. This allows
synchronization of several management systems to the same interval time frame.
Note that the first interval after start-up is always shorter (in the example above, the
first interval only lasts 6 minutes - so that a new interval can start exactly on the 15
minute interval, in this case 11:30:00). During the initial start-up interval i.e. 6 minutes
in the example above, polling is not performed.

Performance Monitoring and Alarms 14 Document #: LTRT-32111
Mediant 3000 with TP-6310
2.1 Frame: DS3 Monitoring (History)
2.1.1 Tab: DS3 Statistics
Frame: DS3 Monitoring (History), Tab: DS3 Statistics
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
DS3 PESs HIST Gauge The counter associated with the number of P-bit
Errored Seconds.
Mib name: dsx3IntervalPESs
DS3 PSESs HIST Gauge The counter associated with the number of P-bit
Severely Errored Seconds.
Mib name: dsx3IntervalPSESs
DS3 UASs HIST Gauge The counter associated with the number of Unavailable
Seconds. This object may decrease if the occurrence of
unavailable seconds occurs across an interval
boundary.
Mib name: dsx3IntervalUASs
DS3 LCVs HIST Gauge The counter associated with the numbe
r of Line Coding
Violations.
Mib name: dsx3IntervalLCVs
DS3 PCVs HIST Gauge The counter associated with the number of P-bit
Coding Violations.
Mib name: dsx3IntervalPCVs
DS3 LESs HIST Gauge The number of Line Errored Seconds (BPVs or illegal
zero sequences).
Mib name: dsx3IntervalLESs
DS3 CCVs HIST Gauge The number of C-bit Coding Violations.
Mib name: dsx3IntervalCCVs
DS3 CESs HIST Gauge The number of C-bit Errored Seconds.
Mib name: dsx3IntervalCESs
DS3 CSESs HIST Gauge The number of C-bit Severely Errored Seconds.
Mib name: dsx3IntervalCSESs

Version 7.0 15 Performance Monitoring and Alarms
Performance Monitoring and Alarms 2. Performance Monitoring Parameters
2.2 Frame: DS3 Monitoring (Real-Time)
2.2.1 Tab: DS3 Statistics
Frame: DS3 Monitoring (Real-Time), Tab: DS3 Statistics
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
DS3 PESs RT Gauge The counter associated with the number of P-bit
Errored Seconds.
Mib name: dsx3CurrentPESs
DS3 PSESs RT Gauge The counter associated with the number of P-bit
Severely Errored Seconds.
Mib name: dsx3CurrentPSESs
DS3 UASs RT Gauge The counter associated with the number of Unavailable
Seconds.
Mib name: dsx3CurrentUASs
DS3 LCVs RT Gauge The counter associated with the number of Line Coding
Violations.
Mib name: dsx3CurrentLCVs
DS3 PCVs RT Gauge The counter associated with the number of P-bit
Coding Violations.
Mib name: dsx3CurrentPCVs
DS3 LESs RT Gauge The number of Line Errored Seconds.
Mib name: dsx3CurrentLESs
DS3 CCVs RT Gauge The number of C-bit Coding Violations.
Mib name: dsx3CurrentCCVs
DS3 CESs RT Gauge The number of C-bit Errored Seconds.
Mib name: dsx3CurrentCESs
DS3 CSESs RT Gauge The number of C-bit Severely Errored Seconds.
Mib name: dsx3CurrentCSESs

Performance Monitoring and Alarms 16 Document #: LTRT-32111
Mediant 3000 with TP-6310
2.3 Frame: Fiber Group Monitoring (Real-Time)
2.3.1 Tab: Fiber Group Statistics
Frame: Fiber Group Monitoring (Real-Time), Tab: Fiber Group Statistics
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Section ESs RT Gauge The counter associated with the number of Errored
Seconds encountered by a SONET/SDH Section in the
current 15 minute interval.
Mib name: sonetSectionCurrentESs
Section SESs RT Gauge The counter associated with the number of Severely
Errored Seconds encountered by a SONET/SDH
Section in the current 15 minute interval.
Mib name: sonetSectionCurrentSESs
Section CVs RT Gauge The counter associated with the number of Coding
Violations encountered by a SONET/SDH Section in
the current 15 minute interval.
Mib name: sonetSectionCurrentCVs
Line ESs RT Gauge The counter associated with the number of Errored
Seconds encountered by a SONET/SDH Line in the
current 15 minute interval.
Mib name: sonetLineCurrentESs
Line SESs RT Gauge The counter associated with the number of Severely
Errored Seconds encountered by a SONET/SDH Line
in the current 15 minute interval.
Mib name: sonetLineCurrentSESs
Line CVs RT Gauge The counter associated with the number of Coding
Violations encountered by a SONET/SDH Line in the
current 15 minute interval.
Mib name: sonetLineCurrentCVs
Line UASs RT Gauge The counter associated with the number of Unavailable
Seconds encountered by a SONET/SDH Line in the
current 15 minute interval.
Mib name: sonetLineCurrentUASs
Path ESs RT Gauge The counter associated with the number of Errored
Seconds encountered by a SONET/SDH Path in the
current 15 minute interval.
Mib name: sonetPathCurrentESs
Path SESs RT Gauge The counter associated with the number of Severely
Errored Seconds encountered by a SONET/SDH Path
in the current 15 minute interval.
Mib name: sonetPathCurrentSESs

Version 7.0 17 Performance Monitoring and Alarms
Performance Monitoring and Alarms 2. Performance Monitoring Parameters
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Path CVs RT Gauge The counter associated with the number of Coding
Violations encountered by a SONET/SDH Path in the
current 15 minute interval.
Mib name: sonetPathCurrentCVs
Path UASs RT Gauge The counter associated with the number of Unavailable
Seconds encountered by a Path in the current 15
minute interval.
Mib name: sonetPathCurrentUASs
2.4 Frame: Gateway System Monitoring (Configuration)
2.4.1 Tab: System IP
Frame: Gateway System Monitoring (Configuration), Tab: System IP
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Number of Outgoing
KBytes HIST Counter Counts the total number of outgoing Kbytes (1000 bytes) from the interface during the last interval.
Mib name: acPMNetUtilKBytesVolumeTx
Number of Incoming
KBytes HIST Counter Counts the total number of Kbytes (1000 bytes) received on the interface, including those received in
error, during the last interval.
Mib name: acPMNetUtilKBytesVolumeRx
Number of Outgoing Pkts HIST Counter Counts the total number of outgoing Packets from the
interface during the last interval.
Mib name: acPMNetUtilPacketsVolumeTx
Number of Incoming Pkts HIST Counter Counts the total number of Packets received on the
interface, including those received in error, during the
last interval.
Mib name: acPMNetUtilPacketsVolumeRx
Number of Incoming
Discarded Pkts HIST Counter Counts the total number of malformed IP Packets received on the interface during the last interval. These
are packets which are corrupted or discarded due to
errors in their IP headers, including bad checksums,
version number mismatch, other format errors, time-to-
live exceeded, errors discovered in processing their IP
options, etc.
Mib name: acPMNetUtilDiscardedPacketsVal

Performance Monitoring and Alarms 18 Document #: LTRT-32111
Mediant 3000 with TP-6310
2.4.2 Tab: VoP Call Statistics
Frame: Gateway System Monitoring (Configuration), Tab: VoP Call Statistics
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Num of Active Contexts
Avg HIST Gauge Indicates the average number of voice calls connected on the gateway since the last clear.
Mib name: acPMActiveContextCountAverage
Num of Active Contexts
Min HIST Gauge Indicates the minimum number of voice calls connected on the gateway since the last clear.
Mib name: acPMActiveContextCountMin
Num of Active Contexts
Max HIST Gauge Indicates the maximum number of voice calls connected on the gateway since the last clear.
Mib name: acPMActiveContextCountMax
G711 Active Calls Avg HIST Gauge
Indicates the average number of G.711 calls present on
the TPM.
Mib name: acPMChannelsPerCoderAverageG711
G723 Active Calls Avg HIST Gauge Indicates the average number
of G.723 calls present on
the TPM. This attribute is only displayed if the G.723
Codec is provisioned on the DSP template.
Mib name: acPMChannelsPerCoderAverageG723
G728 Active Calls Avg HIST Gauge
Indicates the average number of G.728 calls present on
the TPM. This attribute is only displayed if the G.728
Codec is provisioned on the DSP template.
Mib name: acPMChannelsPerCoderAverageG728
G729a Active Calls Avg HIST Gauge Indicates the average number of G.729a calls present
on the TPM. This attribute is only displayed if the
G.729a Codec is provisioned on the DSP.
Mib name: acPMChannelsPerCoderAverageG729a
G729e Active Calls Avg HIST Gauge Indicates the average number of G.729e calls present
on the TPM. This attribute is only displayed if the
G.729e Codec is provisioned on the DSP template.
Mib name: acPMChannelsPerCoderAverageG729e
AMR Active Calls Avg HIST Gauge Indicates the average number of AMR calls present on
the TPM. This attribute is only displayed if the AMR
Codec is provisioned on the DSP template.
Mib name: acPMChannelsPerCoderAverageAMR
EVRC Active Calls Avg HIST Gauge Indicates the average number of EVRC calls present
on the TPM. This attribute is only displayed if the EVRC
Codec is provisioned on the DSP template.
Mib name: acPMChannelsPerCoderAverageEVRC

Version 7.0 19 Performance Monitoring and Alarms
Performance Monitoring and Alarms 2. Performance Monitoring Parameters
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Rx RTP Packet Loss
Max HIST Gauge Indicates the Max Rx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the
collection interval, as indicated by the time Interval.
Mib name: acPMModuleRTPPacketLossRxMax
Tx RTP Packet Loss
Max HIST Gauge Indicates the Max Tx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the
collection interval, as indicated by the time Interval.
Mib name: acPMModuleRTPPacketLossTxMax
RTP delay Average HIST Gauge Indicates the average RTP packets delay per TPM, up
to this point in time during the collection interval, as
indicated by the time Interval.
Mib name: acPMModulePacketDelayAverage
RTP delay Max HIST Gauge Indicates the maximum RTP packets delay per TPM,
up to this point in time during the collection interval, as
indicated by the time Interval.
Mib name: acPMModulePacketDelayMax
RTP delay Min HIST Gauge Indicates the minimum RTP packets delay per TPM, up
to this point in time during the collection interval, as
indicated by the time Interval.
Mib name: acPMModulePacketDelayMin
RTP jitter Average HIST Gauge
Indicates the average RTP packets jitter per TPM, up to
this point in time during the collection interval, as
indicated by the time Interval.
Mib name: acPMModulePacketJitterAverage
RTP jitter Min HIST Gauge Indicates the minimum RTP packets jitter per TPM, up
to this point in time during the collection interval, as
indicated by the time Interval.
Mib name: acPMModulePacketJitterMin
RTP jitter Max HIST Gauge Indicates the maximum RTP packets jitter per TPM, up
to this point in time during the collection interval, as
indicated by the time Interval.
Mib name: acPMModulePacketJitterMax
Rx RTP Bytes Max HIST Gauge Indicates the Max Tx RTP Bytes per TPM, up to this
point in time during the collection interval, as indicated
by the time Interval.
Mib name: acPMModuleRTPBytesRxMax
Tx RTP Bytes Max HIST Gauge Indicates the Max Rx RTP Bytes per TPM, up to this
point in time during the collection interval, as indicated
by the time Interval.
Mib name: acPMModuleRTPBytesTxMax

Performance Monitoring and Alarms 20 Document #: LTRT-32111
Mediant 3000 with TP-6310
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Rx RTP Packets Max HIST Gauge Indicates the Max Rx RTP Packets per TPM, up to this
point in time during the collection interval, as indicated
by the time Interval.
Mib name: acPMModuleRTPPacketsRxMax
Tx RTP Packets Max HIST Gauge Indicates the Max Tx RTP Packets per TPM, up to this
point in time during the collection interval, as indicated
by the time Interval.
Mib name: acPMModuleRTPPacketsTxMax
RTCP XR Average
Conversational R Factor HIST Gauge Average conversational R factor. Mib name: rtcpXrHistoryAvgRCQ
RTCP XR Maximum
Conversational R Factor HIST Gauge Maximum conversational R factor. Mib name: rtcpXrHistoryMaxRCQ
RTCP XR Minimum
Conversational R Factor HIST Gauge Minimum conversational R factor. Mib name: rtcpXrHistoryMinRCQ
2.4.3 Tab: Common Control
Frame: Gateway System Monitoring (Configuration), Tab: Common Control
EMS Parameter Name RT / Hist Gauge /
Counter Parameter Description
Lifetime in seconds Avg HIST Counter Indicates the Connection lifetime, in seconds.
Mib name: acPMCPConnectionLifetimeAverage
Lifetime in seconds Min HIST Counter Indicates the Connection lifetime, in seconds.
Mib name: acPMCPConnectionLifetimeMin
Lifetime in seconds Max HIST Counter Indicates the Connection lifetime, in seconds.
Mib name: acPMCPConnectionLifetimeMax
MGC response counters HIST Counter Indicates the MGC response counters.
Mib name: acPMCPCommandCounterValRx
MGC command counters HIST Counter Indicates the MGC command counters.
Mib name: acPMCPCommandCounterValTx
MGC Rx retransmissions HIST Counter Counts the number of incoming retransmissions.
Mib name: acPMCPRetransmissionCountValRx
MGC Tx retransmissions HIST Counter Counts the number of transactions retransmissions
sent from the board.
Mib name: acPMCPRetransmissionCountValTx
Call Attempts Per Sec
Average HIST Counter Average of call attempts (successful and unsuccessful) per second, during last interval.
Mib name: acPMCPCallAttemptsPerSecAverage