Aurora AU-ST106A Series User manual

Aurora Limited 16 Alban Park Hatfield Road St Albans Hertfordshire AL4 0JJ United Kingdom
Website: www.auroralighting.com
Document version - AU-ST106A_AU-ST110A_V1_14 ENG
AU-ST106A, AU-ST110A
24V DC IP68 SINGLE COLOUR FLEXIBLE LED STRIP LIGHT
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
LEAVE A COPY FOR THE USER / MAINTENANCE ENGINEER FOR FUTURE REFERENCE
IMPORTANT INSTALLATION INFORMATION
Installation should be carried out in accordance with the latest edition of the I.E.E. Wiring Regulations.
Only Qualified Electricians should install this luminaire.
The LED Strip operates at 24V DC.
Before commencing installation or maintenance, ensure electricity is switched off at the mains.
Insure that ALL electrical connections are tight with no loose strands, including factory connections.
IP68 – Protected against submersion in water.
Note: All joints, end caps and connections maximum IP67.
This product cannot be dimmed.
AU-ST106A LED strip may be cut to length with cut points every 6 LEDs (approx. 165mm).
AU-ST106A minimum cut length 165mm.
AU-ST110A LED strip may be cut to length with cut points every 6 LEDs (approx. 100mm).
AU-ST110A minimum cut length 100mm.
For runs over 10m, individual lengths should be connected in parallel.
Minimum bend radius 120mm.
24V DC LED Flexible Strip Light and Accessories
AU-ST106A Round Top Flexible LED strip light AU-ST110A Flat Top Flexible LED strip light
(available in white
/
warm white/blue) (available in white
/
warm white/blue)
AU-ST106ACK LED Flex connector Kit AU-ST110ACK LED Flex connector Kit
AU-ST106CH1 500mm LED Flex channel accessory AU-ST110ACH1 500mm LED Flex channel accessory
AU-ST106CH2 50mm LED Flex mini channel accessory AU-ST110ACH2 50mm LED Flex mini channel accessory
AU-ST106CH3 1m LED Flex channel accessory AU-ST110ACH3 1m LED Flex channel accessory
INSTALLATION INSTRUCTIONS
Before commencing installation or maintenance, ensure electricity is switched off at the mains.
1. To connect the lead and end caps, see also Fig. 1:
Ensure strip is cut smoothly at the indicated cutting points only. Cuts must be at 90° angles.
Push metal clip onto end of flexible strip. Flanges should be pushed up against end surface.
Add extruded metal component over clip, making sure holes are facing outwards.
Offer up end cap with rubber gasket, align holes with extruded metal component.
For the connector, align flat pins with strip conductors and push into flexible strip. Positive pin should be at the bottom. Ensure rubber gasket is in place.
Add screws (x4) and tighten.
2. The AU-ST106A Flex strip can be mounted using the AU-ST106CH1 channel, AU-ST106CH2 mini channel, and AU-ST106CH3 channel accessories.
3. The AU-ST110A Flex strip can be mounted using the AU-ST110ACH1 channel, AU-ST110ACH2 mini channel, and AU-ST110ACH3 channel accessories.
Fig. 1
1. 2.
(Fig.1 continued page 2)
3. 4.
STRIP
CLIP
STRIP
CLIP
EXTRUSION
EXTRUSION
STRIP
RUBBER GASKET
E
N
D
C
A
P
EXTRUSION STRIP
ADD SCREWS, TIGHTEN (x4)
H
O
L
E

To add connector, follow steps 1 and 2, and then steps 5 and 6:
5.
6.
Fig. 2
Other installation warnings and limitations:
Environmental Protection (W.E.E.E.) – Aurora’s WEEE Reg.No. WEE/BG0130YX (UK Only)
Waste Electrical & Electronic Equipment Regulations (WEEE) requires that any of our products showing this marking (left) must not be disposed of with other
household or commercial waste. Aurora does not levy any WEEE disposal charges to its customers for affected WEEE related products. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate any such product from other waste types and recycle it responsibly
at your local facilities. Check with your Local Authority, Recycling Centre or retailer for recycling advice. If, when you purchased any Aurora product, your
supplier included a WEEE disposal fee, you should then contact your supplier for advice on his take back of the product for the correct disposal.
WARRANTY
See www.auroralighting.com for full details of warranty and Extended Warranty Terms and Conditions. The warranty is invalid in the case of improper use, tampering, and
removal of the Q.C. date label, installation in an improper working environment or installation not according to the current edition of the National Wiring Regulations. Should this
product fail during the warranty period it will be replaced free of charge, this is subject to correct installation and return of the faulty product. Aurora does not accept
responsibility for any installation costs associated with the replacement of this product. This warranty is in addition to the statutory rights in your country of purchase. Aurora
reserves the right to alter specifications without prior notice.
EXTRUSION
EXTRUSION
+
STRIP
RUBBER GASKET
CONNECTOR
ALIGN PINS WITH CONTACTS
ADD SCREWS, TIGHTEN (x4)
STRIP
+