Autonics FX Series User manual

J-50
FX/FXH/FXL Series
Features
Ordering information
DIN W72×H72, W48×H96, W144×H72mm counter/timer
●36 input modes and 20 output modes
●Counting speed : 1cps/30cps/2kcps/5kcps
●Selectable voltage input(PNP) or No voltage input(NPN)
●Addition of Up/Down input mode
●Wide range of power supply
: 100-240VAC 50/60Hz, 12-24VAC/DC(Option)
●Selectable Counter/Timer by internal DIP switch
●Various time range
●Built-in Microprocessor
Specifications
Model
Single preset FX4 FX6 FX4H
--
Dual preset FX4-2P FX6-2P FX4H-2P FX4L-2P FX6L-2P
Totalizer(Indicator) FX4-I FX6-I FX4H-I FX4L-I FX6L-I
Digit 4digit 6digit 4digit 4digit 6digit
Digit size W8×H14mm W4×H8mm W6×H10mm W8×H14mm
Power supply 100-240VAC 50/60Hz, 12-24VAC/DC(Option)
Allowable voltage range 90 to 110% of rated voltage
Power consumption
• Indicator : Approx. 6VA(240VAC 60Hz), Approx. 2.7W(24VDC), Approx. 5.8VA(24VAC 60Hz)
•Single preset : Approx. 7VA(240VAC 60Hz), Approx. 3.3W(24VDC), Approx. 6.8VA(24VAC 60Hz)
•Dual preset: Approx. 8VA(240VAC 60Hz), Approx. 3.8W(24VDC), Approx. 7.6VA(24VAC 60Hz)
Max. counting speed for CP1, CP2 Selectable 1cps/30cps/2kcps/5kcps by internal DIP switch
Min. input
signal width
RESET input Approx. 20ms
INHIBIT input
Input
CP1, CP2 input
(INHIBIT)
Input logic is selectable
[Voltage input] Input impedance : 5.4kΩ, "H" level : 5-30VDC, "L" level : 0-2VDC
[No-voltage input] Impedance at short-circuit : Max. 1kΩ, Residual voltage at short-circuit : Max. 2VDC,
Impedance at open-circuit : Min. 100kΩ
RESET input
One-shot output time • Single preset type - 0.05 to 5sec.
• Dual preset type - 1st. output 0.5sec. fixed, 2st. output : 0.05 to 5sec.
Control
output
Contact Type Single preset type : SPDT(1c), Dual preset type : 1st output SPDT(1c), 2nd output SPDT(1c)
Capacity 250VAC 3A at resistive load
Solid-
state
Type Single preset type : 1 NPN open collector
Dual preset type : 1st output 1 NPN open collector, 2nd output 1 NPN open collector
Capacity 30VDC Max. 100mA Max.
Memory protection 10 years(When using non-volatile semiconductor memory)
External sensor power 12VDC±10% 50mA Max.
Environ
-ment
Ambient temperature -10 to 55℃, storage: -25 to 65℃
Ambient humidity 35 to 85%RH, storage: 35 to 85%RH
Insulation resistance Min. 100MΩ(at 500VDC megger)
Dielectric strength 2000VAC 50/60Hz for 1 minute
Noise
strength
AC power ±2kV the square wave noise(pulse width : 1㎲) by the noise simulator
DC power ±500V the square wave noise(pulse width : 1㎲) by the noise simulator
Item
Digit
Size
Output
FX 4 H 2P IIndicator
No mark Single preset
2P Dual preset
LDINW144×H72
mm
HDINW48×H96
mm
No mark DIN W72×H72mm
4 9999(4digit)
6 999999(6digit)
FX Counter/Timer
Please read “Caution for your safety” in operation
manual before using.

J-51
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
power
supply
(Q)
Stepping
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
Up/Down Counter/Timer
8
88 8
88
9
999
99 10
10 10 10
10 10 11
11 11 11
11 11 12
12 12 12
12 12 13
13 13 13
13 13 14
14 14 14
14 14
15
15 15 15
15 15
16
16 16 16
16 16
18 18 18
17
17 17 17
17 17
1
11 1
11 2
222
22 3
333
33 4
444
44 5
55 5
55 6
66 6
66 7
77 7
77
88 99 10 10
11 11 12 12
13 13 14 14 15 15 16 16 18 18 19 19 20 20 21 21 22 22 23 23 24 24 17 17
11 22 33 44 55 66 77
CP1 CP1 CP1
CP2 CP2 CP2
0V 0V 0V
RESET RESET RESET
(INHIBIT) (INHIBIT) (INHIBIT)
+12VDC
50mA
+12VDC
50mA
+12VDC
50mA
OUT1 OUT
OUT
(Note1) (Note1) (Note1)
※1 ※1※2 ※2
(Note1) (Note1)(Note1)
(Note2) (Note2) (Note2)
(Note2) (Note2)(Note2)
OUT2
OUT2 OUT1
SOURCE
SOURCE
SOURCE SOURCE
OUT1
OUT1
OUT1
OUT2
OUT2
OUT2
CP1 CP1
CP1 CP1CP1
CP2 CP2
CP2 CP2 CP2
0V0V 0V
0V 0V
0V0V 0V
(INHIBIT)
(INHIBIT)
(INHIBIT) (INHIBIT)
(INHIBIT)
+12VDC
50mA +12VDC
50mA
+12VDC
50mA
+12VDC
50mA
+12VDC
50mA
RESET RESET
RESET RESET RESET
OUT1
(1st)
OUT2
(2nd)
SOURCESOURCE
SOURCE SOURCE
-
-
--
--
--
+
+
++
++
++
SOLID
STATE OUT
SOLID
STATE OUT
SOLID
STATE
OUT
SOLID STATE OUT
SOLID
STATE
OUT
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
100-240VAC
50/60Hz
12-24VDC/AC
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
Vibration
Mechanical 0.75mm amplitude at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 1 hour
Malfunction 0.5mm amplitude at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 10 minutes
Shock
Mechanical 300m/s²(Approx. 30G) in each of X, Y, Z directions for 3 times
Malfunction 100m/s²(Approx. 10G) in each of X, Y, Z directions for 3 times
Relay
life cycle
Mechanical Min. 10,000,000 operations
Electrical Min. 100,000 operations at 250VAC 2A(resistive load)
Approval
Unit weight
FX4 : Approx.
295gFX4-
2P :Approx.
305gFX4-I
:Approx. 260g
FX6 : Approx.
305gFX6-
2P :Approx.
315gFX6-I
:Approx. 265g
FX4H :Approx. 325gFX4H-2P
:Approx. 353gFX4H-I :Approx.
297g
FX4L-2P
:Approx.
544gFX4L-I
:Approx. 455g
FX6L-2P
:Approx.
550gFX6L-I
:Approx. 461g
Specifications
Connections
●FX -2P
●FX4H-2P
●FX L-2P ●FX L-I
●FX -I
●FX4H-I
●FX
●FX4H
※CP2(INHIBIT) : Time hold terminal when using for timer.
※
It is operated by power ON start type when using for timer.
※ 1. Connection for PNP input
2. Connection for NPN input
※Environment resistance is rated at no freezing or condensation.

J-52
72 14 112
67
Min. 91
86
Min. 91
48 13 100
90
Min. 102
96
100
Min. 50
156
143 10 112
67
Min. 76
71.5
Min. 170
Sensor
Sensor
Sensor
Sensor
Counter/Timer
Counter/Timer
Counter/Timer
Counter/Timer
Counter/Timer
Counter/Timer
(NPN output)
(PNP output)
(NPN open
collector output)
(PNP open
collector output)
※CP1, CP2(INHIBIT), RESET input
※CP1, CP2(INHIBIT), RESET Input
Brown Brown
Brown Brown
Black Black
Black Black
Blue Blue
Blue Blue
※※
※※
※
※
0V
0V 0V
0V
0V
+12V +12V
+12V +12V
+12V
+12V
5.4㏀5.4㏀
5.4㏀5.4㏀
5.4㏀
5.4㏀
Inner
circuit
Inner
circuit
Inner
circuit
Inner
circuit
Inner
circuit
Counting speed :
1 or 30cps setting(Counter)
Counting speed :
1 or 30cps setting(Counter)
Inner
circuit
RL
10㏀
RL
10㏀
Dimensions
●FX Series
●FXH Series
●FXL Series
●Panel cut-out
●Panel cut-out
●Panel cut-out
●Solid-state input(Standard sensor : NPN output type sensor)
●Solid-state input(Standard sensor : PNP output type sensor)
●Contact input
●Contact input
(unit: mm)
(unit: mm)
(unit: mm)
Input connections
No-voltage input(NPN)(Factory default)
Voltage input(PNP)
68.5+0.7
0
45+0.6
0
138+1.0
0
92+0.8
0 68.5+0.7
0
68.5+0.7
0
FX/FXH/FXL Series

J-53
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
power
supply
(Q)
Stepping
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
• No-voltage input
(NPN)
※Please be sure to turn power OFF before changing input logic.
• No-voltage input
(NPN)
Direction of
front display
Direction of
front display
• No-voltageinpu(NPN)
• Voltage input(PNP) • Voltage input
(PNP)
• Voltage input(PNP)
NPN NPN
NPN
(NPN)
NPN
PNP PNP
S
S
F
F
PNP
(PNP)
PNP
88
8
99
9
10 10
10
11 11
11
12 12
12
13 13
13
14 14
14
1
1
2
2
3
3
4
4
5
5
6
6
7
7
Black Brown Blue
Load1
Load1
CP1
CP1
CP2
CP2
+12V
+12V
0V
0V
SOURCE
SOURCE
-
-
+
+
Load2
Load2
(Power supply
for the load)
(Power supply
for the load)
Constant-voltage
circuit
External
power supply
(FX4)
(FX4) (FX6-I)
(Power supply
for the load)
※
(-)
(+)
(-)
(+)
8 9 10 11 12 13 14
Black Brown
Blue
8 9 10 11 12 13 14
Black Blue
Input logic selection
Input & output connections
●FX Series
Input logic is changeable by input logic
selection switch located at the one-side
of case.
●Please select proper capacity of load, because total
value of load capacity and current consumption should
not be exceed current capacity.(Max. 50mA)
This unit starts to count when "High" level(5-30VDC)
is applied at CP1 or CP2 after selecting PNP.
Please connect as the power of sensor is supplied from only one of counters and design input logic with same way.
●
The capacity of the load must not be exceed max. 30VDC,
max. 100mA of the switching capacity of the transistor.
●Please do not supply the reverse polarity voltage.
※Please connector the surge absorber(Diode) at both
terminals of the load, in case of using the inductive load.
(Relay, etc.)
Input logic is changeable by
input logic selection switch
located at the terminal block.
Input logic is changeable by input
logic selection switch(SW3) located
at inside of the case.
●FXL Series ●FXH Series
In case of operating the load by power
supply of the sensor
How to count by external power supply
Using 2 counters with one sensor
In case of operating the load by
external power supply
CP1 CP2 +12V 0V
CP1 CP1CP2 CP2+12V +12V0V 0V
Up/Down Counter/Timer

J-54
●FX Series ●FXH Series ●FXL Series
Description of inner DIP switches
SW2 Functions
3
Conter
Timer
SW1 Functions
4
Down mode
Up mode
SW2 Functions
4
Disable the
memory protection
Enable the
memory protection
Dual
preset
Counter
/Timer
type
Counter
only
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW2 Functions
1cps
30cps
2kcps
5kcps
ON
ON
ON
ON
OFF
OFF
OFF
OFF
*** *Single preset model
(There is no. 8 of SW1)
** Indication model
(There is no. 5, 6, 7, 8
of SW1)
SW1
SW1 SW1
SW2
SW2 SW2
876543214321
RESET
2nd preset
1st preset
0
1st output
※
This mode selects a one-shot output(0.5sec. fixed)
or retained output(Until 2nd output turns off) for
1st output in the dual preset counter.
One-shot output
0.5sec
Retained output
Retained output2nd output
●Max. counting speed
●1st output one-shot(ON/OFF) ※Example of F output operation mode
●Conter/Timer selection ●Memory protection
●Up/Down mode selection
ON
ON
OFF
OFF
1st output one-shot(ON/OFF)
Output mode
Up/Down mode
Count input mode(Counter)
Time setting mode(Timer)
Memory protection(ON/OFF)
Counter/Timer selection
Max. counting speed(Counter)
FX/FXH/FXL Series

J-55
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
power
supply
(Q)
Stepping
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
Input operation(Counter)
※ Ⓐ: Over min. signal width, Ⓑ: Over 1/2 of min. signal width.
If the signal width of Ⓐor Ⓑ is less than min. signal width, ±1 of count error is occured.
Input mode SW1 No-voltage input type(NPN) Voltage input type(PNP)
Up
mode
Up/Down-A
(Command
input)
Up/Down-B
(Individual
input)
Up/Down-C
(Phase
difference
input)
Up
(Count
up input)
Down
mode
Up/Down-D
(Command
input)
Up/Down-E
(Individual
input)
Up/Down-F
(Phase
difference
input)
Down
(Count
down input)
ON
OFF
ON
OFF
2
43
Count
value
cp1
cp2
H
H
011
222
33
ⒶⒶ
L
L
Count
value
cp1
cp2
H
H
011
222
33
ⒶⒶ
L
L
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
4
2
2
2
2
2
2
2
3
3
3
3
3
3
3
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
cp1
cp1
cp1
cp1
cp1
cp1
cp1
cp1
cp1
cp2
cp2
cp2
cp2
cp2
cp2
cp2
cp2
cp2
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
0
0
0
0
n-1
n-1
n-1
n-1 n-1
n-1
n-1
n-1
n-1
n
n
n
n
n
n-2 n-2
n-2
n-2n-2
n-2
n-2
n-2
n-2
n-2
n-2
n-3
n-3
n-3
n-3
n-3
n-4
n-4
n-5
n-5
n-3
n-3
n-3
0
0
0
0
0
1
1
1
1
1
1
1
2
2
2
2
3
3
No counting
No counting
No counting
No counting
4
4
5
5
2
2
2
2
3
3
3
3
Ⓐ
ⒶⒶ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
ⒷⒷⒷⒷ
ⒷⒷⒷⒷ
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
Count
value
cp1
cp1
cp1
cp1
cp1
cp1
cp1
cp1
cp1
cp2
cp2
cp2
cp2
cp2
cp2
cp2
cp2
cp2
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
0
0
0
0
n-1
n-1
n-1
n-1 n-1
n-1
n-1
n-1
n-1
n
n
n
n
n
n-2 n-2
n-2
n-2
n-2
n-2
n-2
n-2
n-2
n-2
n-2
n-3
n-3
n-3
n-3
n-3
n-4
n-4
n-5
n-5
n-3
n-3
n-3
0
0
0
0
0
1
1
1
1
1
1
1
2
2
2
2
3
3
No counting
No counting
No counting
No counting
4
4
5
5
2
2
2
2
3
3
3
3
Ⓐ
ⒶⒶ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
Ⓐ
ⒷⒷⒷⒷ
ⒷⒷⒷⒷ
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Up/Down Counter/Timer

J-56
Decimal
point
setting
RESET
RESET
INHIBIT
INHIBIT
RESET
RESET
RESET
RESET
+Display
value
+Max. time
range
+Max. time
range
-Max. time
range
+Display
value
-Display
value
-Display
value
-Display
value
+Display
value
+Display
value
0
0
0
0
0
0
RUN mode
RESET RESET
RESET
RESET
key 3sec. key 3sec.
Decimal point setting
Decimal point setting display
(" " Flashing)
Time setting mode(Timer)
Counting operation of indication
type(Counter)
Setting function of Decimal point
Time operation of indication type
(Timer)
●Up mode
●Up / Down-A, B, C mode
●Decimal point setting
●Down mode
●Up / Down-D, E, F mode
●Up mode
●Down mode
SW1 4digit 6digit
A99.99sec 99999.9sec
B999.9sec 999999sec
C9999sec 99min 59.99sec
D99min 59sec 999min 59.9sec
E999.9min 9999.9min
F99hour 59min 99hour 59min 59sec
G999.9hour 9999hour 59min
H9999hour 99999.9hour
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
3
3
3
3
3
3
3
3
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
※ It advances to "Decimal point setting mode" if press RESET
key for 3sec.
※ It returns to RUN mode by press RESET key for 3sec in
"Decimal point setting mode".
※ It returns to RUN mode if no RESET button or digital switch
(Dual-setting digital switch for dual preset type) is applied for
60sec. in the "Decimal point setting mode".
※ The decimal point setting does not exist in indicator.
※ Existing decimal point setting is displayed when entering into decimal point setting mode.
※ If pressing one of digital switch(2nd preset type: 2nd preset digital switch) Up(+) buttons in decimal point setting mode,
decimal point will be moved to Up(+) direction.
If pressing one of digital switch(2nd preset type: 2nd preset digital switch) Down(-) buttons, decimal point will be moved
to Down(-) direction.
• The decimal point setting of 6digits indicator • The decimal point setting of 4digits indicator
FX/FXH/FXL Series

J-57
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
power
supply
(Q)
Stepping
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
Output operation mode
One-shot output
(0.05 to 5sec.) of 2nd output
Retained output
One-shot output(0.5sec.) of 1st output
※The output of single preset
type is operated at the status
of the second output mode
Retained
output
※One-shot output time is set by front TIME adjuster.
Output mode
(SW1)
Up mode Down mode Operation after count up
Up, Up / Down-A, B, C Down, Up / Down-D, E, F
FThe display value continues until Reset
signalapplied and the output is held.
• 1st retained output and 2nd output are
maintained until Reset signal is applied.
• When using 1st output as one-shot output,
it will return after operating for 0.5sec.
N
The display value and output will be held
until Reset input is applied.
CThe display value will be Reset Start status
as soon as it reaches to 2nd setting value.
• 1st retained output will be OFF after 2nd
one-shot output.
• 1st one-shot output will be reset after
operating 0.5sec., and it is not related to
2nd output.
RDisplay value will be maintained until 2nd
output is Off, then it will be reset.
• 1st retained output will be OFF after 2nd
one-shot output.
• 1st one-shot output will be reset after
operating 0.5sec., and it is not related to
2nd output.
KThe display value continues until Reset
signalapplied.
• 1st retained output will be OFF after 2nd
one-shot output.
• 1st one-shot output will be reset after
operating 0.5sec., and it is not related to
2nd output.
PThe display value will be Reset Start status
as soon as it reaches to 2nd setting value.
• 1st retained output will be OFF after 2nd
one-shot output.
• 1st one-shot output will be reset after
operating 0.5sec., and it is not related to
2nd output.
QThe display continues until 2nd output is
OFF.
• 1st retained output will be OFF after 2nd
one-shot output.
• 1st one-shot output will be reset after
operating 0.5sec. not related to 2nd output.
SUp Down
• Up, Up/Down-A, B, C input mode
- OUT1 is ON when(Display value) ≥
(1st setting value)
- OUT2 is ON when(Display value) ≥
(Dual setting value)
• Down, Up/Down-D, E, F input mode
- OUT1 is ON when(Display value) ≤
(1st setting value)
- OUT2 is ON when(Display value) ≤
(Zero)
Counter
Up / Down-A, B, C Up / Down-D, E, F
S
When it is used as Timer, 1st output and
2nd output are flashing repeatedly.
Timer
4
ON
OFF
4
ON
OFF
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
0
0
0
0
0
0
0
0
0
0
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
2nd Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
1st Preset
0
0
0
0
0
0
0
0
0
0
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
1st Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
2nd Output
567
ON
OFF
567
ON
OFF
567
ON
OFF
567
ON
OFF
567
ON
OFF
567
ON
OFF
567
ON
OFF
567
ON
OFF
567
ON
OFF
Up/Down Counter/Timer

J-58
Power
The inner circuit voltage starts to rise up for the first 100ms
after power on, the input may not work at this time. And
also the inner circuit voltage drops down for the last 500ms
after power off, the input may not work at this time.
Reset input
*
*T
1
Ta Tb
3×Ta
1
**
** **
Proper usage
Ta(ON width) and
Tb(OFF width) needed to be
over min.signal width.
Max. counting speed is 1/2
value of rated spec. when
duty ratio is 1:3.
It can not respond if it is smaller
than min. singal width(Ta).
(INHIBIT)
SW1
CP1 CP2 +12V 0V
INHIBIT
*Setting value
Time display value
0(UP mode)
ENC-1-2-T-24
Please put black dot. Please put black dot.
Ex1)Measurement of length by
the rotary encoder
EX2)Timer[F mode]
※1 ※2
8 9 10 11 12 13 14 ※ 1. Connection for PNP
2. Connection for NPN
FX4
*In case of a contact reset, contact chattering will not
affect the reset as long as it is applied for a minimum of 20ms.
**
Input signal at CP1 & CP2 must be applied for a minimum
of 50ms after the reset is removed.
*Please make duty ratio(ON/OFF) as 1:1.
** Min. signal width
1cps : Min. 500ms
30cps : Min. 16.7ms
2kcps : Min. 0.25ms
5kcps : Min. 0.1ms
Power ON
OFF 100㎳500㎳
The unstable time
against the input signal
※Please be careful of the injury caused by tools.
Unscrew the rear
bolt, and pull the
body backward.
① Push down the front guide.
② Pull out the front guide.
●FXL Series
Reset
●Reset
In case of changing the input mode after supplying the
power, please provide an external reset or manual reset.
If reset is not executed, the counter will be working in
previous mode.
●Reset signal width
To guarantee proper reset, the signal must be supplied for
a minimum of min. 20ms regardless the signal comes from
a contact or a solid-state input.
Mini. count signal width
Max. counting speed
This is a response speed per 1 sec. when the duty ratio
(ON:OFF) of input signal is 1:1. If the duty ratio is not
1:1, the width between ON and OFF should be over min.
signal width and the response speed will getting slower
against input signal. If either ON or OFF signal is shorter
than minimum signal width, this product may not respond.
INHIBIT(For timer)
●INHIBIT mode is active when SW1 turns ON. (Time Hold)
● When power is applied, it starts to progress and INHIBIT mode
is used to stop the time is under the progress at the moment.
●When SW1 is OFF, timer starts to progress again.
How to use the sticker
The below sticker can be found inside the box.
Use the sticker according to application as follow;
Error display
Error signal Error description Returning method
When 2nd setting
value is 0
Change the setting
value to non zero status
When 2nd setting
value is smaller than
1st setting value
Make 2nd setting value
bigger than 1st setting
value
※ There is no Error display function in indication type.
※ There is no Error function in indicator.
※
When Error is display, the OUTPUT continues OFF state.
※ 1st output maintains OFF status by 1st setting value as 0.
Case & DIP switch detachment
●FXH Series
FX/FXH/FXL Series