Autonics LE7M-2 User manual

N-81
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(J)
Temperature
Controllers
(K)
SSRs
(L)
Power
Controllers
(M)
Counters
(N)
Timers
(O)
Digital
Panel Meters
(P)
Indicators
(Q)
Converters
(R)
Digital
Display Units
(S)
Sensor
Controllers
(T)
Switching
Mode Power
Supplies
(U)
Recorders
(V)
HMIs
(W)
Panel PC
(X)
Field Network
Devices
LE7M-2
Ordering Information
Specifications
W72×H72mm, Weekly/Yearly Timer
● Easy to check and change the program setting
● Customizable weekly or yearly unit time setting
and control by user
● Includes daylight saving time function
● Built-in 2 independent control output (relay)
● Flush and surface mounting are in one unit
● Enable to mount on DIN rail with base plate
Model LE7M-2
Power supply 100-240VACᜠ 50/60Hz
Allowable voltage range 90 to 110% of rated voltage
Power consumption Max. 4.2VA (100-240VACᜠ)
RETURN input Short-circuit or open by switch or relay
Timing program 48 steps for weekly, 24 steps for yearly
Operation mode ON/OFF mode, cycle mode, pulse mode
Mounting Front panel, surface, DIN rail
Time deviation ±15 sec/month (ambient temperature: 25℃) (±4 sec/week)
Temperature error ±0.01% ±0.05 sec (ratio by set time)
Memory protection Over 5 years (at 25℃)
Control
Output
Contact type SPDT (Single Pole Double Throw)
Contact capacity 250VACᜠ 10A, 30VDCᜡ 5A resistive load
Output number Independent 2 output (1c×2)
Relay
life cycle
Mechanical Min. 5,000,000 operations (switching capacity: 30 times/min)
Electrical Min. 50,000 operations<switching capacity: 20 times/min, 250VAC 10A (resistive load)>
Insulation resistance Over 100MΩ (at 500VDC megger)
Dielectric strength 2,000VAC 50/60Hz for 1 min
Noise immunity ±2kV the square wave noise (pulse width: 1㎲) by the noise simulator
Environment Ambient temperature -10 to 55℃, storage: -25 to 65℃
Ambient humidity 35 to 85%RH
Approval ᜧ
Unit weight Approx. 272g
Item
Size
Output
LE7 M 2
2 2 Relay outputs
MDIN W72×H72mm
LE7 Weekly/Yearly timer
Features
※Environment resistance is rated at no freezing or condensation.
Please read “Safety Considerations”
in the instruction manual before using.

N-82
LE7M-2
N.C.
N.C.
N.C. N.C.
OUT2
OUT1 SOURCE
SOURCE
SOURCE
[Single phase] [Three phase]
COM
COM
COM COM
N.O.
N.O. N.O.
Power of
single
phase
Load Load
Magnetic
Switch
Magnetic
Switch
Power of
three
phase
N.O.
RETURN
INPUT
CONTACT OUT
250VAC 10A,
30VDC 5A
RESISTIVE LOAD
100-240VAC
50/60Hz 4.2VA
6
1
7
2
8
3
9
4
10
5
1 12 23 34 45 5
Connections
Load Connection
You must connect a surge absorber to the both ends of the load to prevent from damage or malfunction of this unit when
controlling non-resistive load (E.g.: magnetic switch, etc).
● In case of controlling the load directly
● In case of controlling the load by using a magnetic switch
S/A
: Surge Absorber
S/A : Surge Absorber S/A
S/A
N.C.
SOURCE
Power circuit for
load operation
COM
N.O.
부부
1 2 3 4 5
Load

N-83
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(J)
Temperature
Controllers
(K)
SSRs
(L)
Power
Controllers
(M)
Counters
(N)
Timers
(O)
Digital
Panel Meters
(P)
Indicators
(Q)
Converters
(R)
Digital
Display Units
(S)
Sensor
Controllers
(T)
Switching
Mode Power
Supplies
(U)
Recorders
(V)
HMIs
(W)
Panel PC
(X)
Field Network
Devices
Weekly/Yearly Timer
Dimensions
How To Switch From The Flush Mounting To Surface Mounting Type
(unit: mm)
Remove terminals from the body after unscrewing terminal screws, and then assemble terminals to the body after rotating
terminals as shown below.
1) Front panel mounting Bracket Panel cut-out
60
9
412
14.5
Min. 91
Min. 91
68+ 0.7
0
72 6.7
60.3
67.5
10.1
Panel hole cut-out
2) Surface mounting
54.5
85 95
85
4-M3
54.5
13.5
64 67
70.4
3) DIN rail mounting
67.6 9.5
76.5
50 9.5
67.6
2-Ø3.9
95
95
35mm
DIN RAIL
35mm
DIN RAIL
79.9
(Surface mounting)
⑦
Rotate 180˚ centering
vertical axis
③
Rotate 180˚ centering
vertical axis
⑥
Detach terminal block
from case
②
Detach terminal block
from case
(Front panel mounting)
①
Unscrew 4 bolts
from terminal block
⑧
Assemble case and
terminal block
④
Assemble case and
terminal block
⑤
Fix terminal block
to case
⑨
Fix terminal block
to case

N-84
LE7M-2
1
2
14
15
5
16
3
4
6
17
18
9
20
19
7
8
10
21
22
11
12
13
ON time OFF time
Unit Description
Functions
1. Day indicator
2. Day display
● Light: Day is selected.
● Light-out: Day is not selected.
3. Current time setting mode indicator
4. DST display (daylight saving time)
5. AM/PM display
6. Season display
7. Program display
8. Display ON time/day, OFF time/day, ON time width,
OFF time width
9. AM/PM display
10. YEAR display
: It turns ON when set, check, modify, delete yearly
program, set yearly holidays and operate yearly
program.
11. Yearly START/STOP day display
12. Main display
13. Remaining step display
14. Operation mode display
15. Power restore input display
16. Output mode display
17. Year, month, date display
18. Unit of pulse width display
19. Sub-display
20. CHECK key
21. MODE key
22. Operation key
23. Output selection switch
● AUTO: Control output according to the set program.
● ON: Output is ON. (operation)
● OFF: Output is OFF.
※Output 1 (OUT1) and Output 2 (OUT2) are selected
independently.
24. SET key
Program setting and output operation
Output 1/Output 2 operates according to Program 1 and
Program 2.
Definitions
● Record: A part of program that controls output operation.
● Step: Basic component of record.
Operation modes
If the operation mode of Program 1 (program 2) is set on
pulse mode initially, the pulse mode is xed for additional
programs.
If the operation mode of Program 1 (program 2) is set on
ON/OFF or cycle mode initially, pulse mode cannot be
used for additional programs.
● Weekly ON/OFF mode
Output operation by ON/OFF set time.
• Min. time setting unit: 1 min
• It is able to set ON/OFF day separately.
• One record in two Steps
(ON day/ON time, OFF day/OFF time)
● Weekly Cycle mode
Output turns ON for ON time and turns OFF for OFF time.
And the ON/OFF cycle is repeated.
23
24

N-85
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(J)
Temperature
Controllers
(K)
SSRs
(L)
Power
Controllers
(M)
Counters
(N)
Timers
(O)
Digital
Panel Meters
(P)
Indicators
(Q)
Converters
(R)
Digital
Display Units
(S)
Sensor
Controllers
(T)
Switching
Mode Power
Supplies
(U)
Recorders
(V)
HMIs
(W)
Panel PC
(X)
Field Network
Devices
Weekly/Yearly Timer
ON Time
Pulse width
(1 to 59 sec, 1 to 60 min)
ON time ON width OFF time
OFF width
● Yearly ON/OFF mode
Output turns ON at ON time on START date and turns OFF
at OFF time on STOP date.
• One record in three steps
(START/STOP date, ON/OFF time)
● Yearly pulse mode
Output turns ON at ON time on START date and turns
OFF at OFF time on STOP time for a specied pulse width
repeatedly. (pulse width: 1 to 59 sec, 1 to 60 min).
• One record in three steps (START/STOP date, ON time,
pulse width)
⑤ ⑥
Weekly setting 1 of Program 1
Weekly setting 2 of Program 1
Yearly setting 1 of Program 1
Program 1 mode
① ② ③ ④
Program operation
● ①to②: Operated by weekly setting 1 of Program 1.
● ②to③: Operated by weekly setting 2 of Program 1.
● ④to⑤: Operated by weekly setting 1 of Program 1.
● ⑤to⑥: Operated by yearly setting 1 of Program 1.
(during weekly program operation at 12:00 AM on
START date, the weekly program operation stops, and it
changes to yearly program operation mode. The yearly
program operation stops at 12:00 AM on the next day of
STOP date.)
Power restore mode
In setting group 2-Level 2 (power restore), select auto [AT]
or normal [NOR] by or key, and press key to set.
● Auto [AT] power restore mode
Output (OUT1, OUT2) operates according to program
when power turns on again after power failure.
● Normal [NOR] power restore mode
When power turns on again after power failure, output is
kept OFF and RET.IN ashes on the panel. When power
restore input is detected, RET.IN turns o󰀨 and output
operates according to program.
• Power restore input
Input contact signal in external "Return input terminals
(
⑨ to ⑩)" by switch or relay, or press key for 3 sec
in RUN mode.
Please use reliable contacts enough to ow 0.1mA of
current at 5VDC when use switch or relay.
Season switching mode
This feature uses for setting seasonal weekly operation
mode.
To operate this mode, save starting month and date,
ending month and date of each season which displays S1,
S2, S3, S4 then set day and time of each season in weekly
program setting. It is also able to operate only in summer
and winter season. (S1: set summer season, S2: set winter
season, S3/S4: do not set)
At the season switching selection LEVEL 2 status in setting
2 group (SEN turns ON, OFF ashes), select ON [ON] by
pressing or key and press key to complete the
season switching.
Be sure that if changing season switching from OFF to ON
or, ON to OFF, the weekly program 1 (P1) and the weekly
program 2 (P2) which are set before are deleted.
● ON [ON] mode
Weekly program is switched automatically by season
switching.
• Period setting per season
①At the season switching selection LEVEL 2 status in
setting 2 group (SEN ashes, the set season turns ON,
START and STOP turn ON), press key.
 ②Advance to the ashing position of season selection
among S1, S2, S3, S4 by or key and press
key.
 ③After set START month, date per season and press
key.
④
key is pressed after set STOP month, date per
season, it is advanced to LEVEL1 of period setting per
season. Add or adjust the period setting by key.
● It is disable to use when it is OFF [OFF].
● If season terms are overlapped, these are prioritized in
S4>S3>S2>S1 order.
• Set range for ON/OFF time width
: 1min to 12 hour 59 min
• One record in 3 steps (ON day/ON time, OFF day/OFF
time, ON time width/OFF time width)
● Weekly pulse mode
Output turns ON at ON time for a specied pulse width.
(pulse width: 1 to 59 sec, 1 to 60 min)
• One record in two steps (ON day/ON time, pulse width)
Display and change of next mode
● The day of next mode in Program 1 or Program 2 is
displayed on the day indicator, and the time of next
mode is displayed on the lower row of screen.
Press + in RUN mode it is changed from
program 1 to program 2 or from program 2 to program 1.
● In ON/OFF operation mode, set ON time and OFF time
to next mode. In Pulse operation mode, set Pulse ON
time to next mode.

N-86
LE7M-2
Daylight saving time
To utilize daylight during the summer season, daylight
saving time is adjusted forward one hour from standard
time.
In setting group 2-LEVEL 2 (DST turns ON, AT or NOR
ashes.), select Auto [AT] or Normal [NOR] by or key
and press key to set.
● Auto[AT] Daylight Saving Time mode
Current time will be faster as an hour when it is started and
slower as an hour when it is nished.
• Automatic Daylight Saving Time period setting
①
Automatic Daylight Saving Time period setting LEVEL
1 of setting group 2. (DST ashes and START and
STOP turn ON.)
②
Set START date (month, date) of automatic Daylight
Saving Time mode and press key.
③
Set START time (AM/PM, hour) of automatic Daylight
Saving Time mode and press key.
But, the minute will be xed as 00.
④
Set STOP date (month, date) of automatic Daylight
Saving Time mode and press key.
⑤
Set STOP time (AM/PM, hour) of automatic Daylight
Saving Time mode and press key. But, the
minute will be xed as 00.
● Normal [NOR] daylight saving time mode
Press key over 3 sec in RUN mode, +1h turns ON
and current time is faster as an hour and +1h turns ON out
or vice versa, when press key over 3 sec again.
Current time setting
(E.g.) Set the current time as 10, Mar, 2008, 5:10 PM.
SUN MON TUE WED THU FRI SAT
① Advance to the current time setting mode
+ keys are
pressed over 3 sec in
RUN mode, it is advanced
to current time setting of
setting group 2 and clock
will be ashed and tAJ will
be lighted in second display
part, press key.
SUN MON TUE WED THU FRI SAT
② Year, month, date setting
Press or key to set
08 (year 2008) and move
the ashing digit to position
month by key.
Press key after press
or key to set date 10.
SUN MON TUE WED THU FRI SAT
③Current time (AM, PM) setting
Press or key to select
PM and move the ashing
digit to position hour by
key.
SUN MON TUE WED THU FRI SAT
④Current time (hour, min) setting
Press or key to set 5
PM and move the ashing
digit to position min by
key. Press or key to
set 10 min and press
key and it is returned to
RUN mode when press
key over 3 sec
● It advances to "①Current time setting mode" in ON
status and set current time as shown above ② to ④ by
key.
● Current time is set up to 31, Dec., 2099.
● Check current year/month/date in RUN mode When
key is pressed over 3 sec in RUN mode, it advances to
current year/month/date display. After display current
year/month/date for 3 sec, it returns to RUN mode
displaying current display.

N-87
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(J)
Temperature
Controllers
(K)
SSRs
(L)
Power
Controllers
(M)
Counters
(N)
Timers
(O)
Digital
Panel Meters
(P)
Indicators
(Q)
Converters
(R)
Digital
Display Units
(S)
Sensor
Controllers
(T)
Switching
Mode Power
Supplies
(U)
Recorders
(V)
HMIs
(W)
Panel PC
(X)
Field Network
Devices
Weekly/Yearly Timer
RUN mode RUN mode
SET SET
Press MODE key
for 3 sec
Press MODE key
for 3 sec Press MODE key
for 3 sec Press MODE + SET key
for 3 sec
(setting group 1)
※1
※1
※1
※1
※1
※2
(setting group 2)
Program 1 weekly
programsetting mode
(PROG P1 ashes)
Program 1 weekly
program setting Current time setting mode
(clock icon ashes)
Power failure return selection mode
(RET ashes,
AT or NOR turns ON)
Season switching selection mode
(SEN ashes,
ON or OFF turns ON)
Period setting for season mode
(SEN ashes, period-set
season turns ON and
START or STOP turns ON)
Daylight saving time mode
(DST ashes,
AT or NOR turns ON)
Automatic[AT] daylight
saving time period
setting mode [DST] ashes,
START or STOP turns ON)
Current time
setting
Power failure
return selection
Season switching
selection
Period setting
per season
Daylight saving
time selection
Automatic daylight
saving time period setting
Program 2 weekly
programsetting mode
(PROG P2 ashes)
Program 2 weekly
program setting
Program 1 Yearly
programsetting mode
(PROG P1, YEAR ash)
Program 2 yearly program
setting mode
(PROG P2, YEAR ash)
Program 1 weekly program
delete mode
(PROG P1, CLR ash)
Program 2 weekly program
delete mode
(PROG P2, CLR ash)
Program 1 yearly program
delete mode
(PROG P1, YEAR, CLR
ash)
Program 2 yearly program
delete mode
(PROG P2, YEAR, CLR
ash)
Weekly day change mode
(cDY ashes)
Yearly holiday operation mode
(hDY, YEAR ash)
Program 1 yearly
program setting
Program 2 yearly
program setting
All Program 1 weekly
program delete
All Program 2 weekly
program delete
All Program 1 yearly
program delete
All Program 2 yearly
program delete
Standard day,
change day setting
Yearly holiday
operation mode setting
Program Setting
Setting group 1 Setting group 2
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
LEVEL1 LEVEL2
SET SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
※1: When the CLR turns ON, hold the SET key for 3 sec,
the ALL turns ON and all programs are deleted.
● When it advances to setting group 1 in RUN mode,
output (OUT1, OUT2) will be OFF.
● It returns to previous setting group 1 when power of time
switch is ON again in setting group 1.
● When MODE key is pressed in LEVEL2 of setting group 1,
current setting will be canceled and it returns to previous
LEVEL1.
※1: Season switching selection is OFF.
※2: Automatic switching selection of Daylight Saving Time
is Normal [NOR].
● When it advances to setting group 2 in RUN mode,
output (OUT1, OUT2) will be OFF.
● When power of time switch is ON again in setting group 2,
it returns to previous setting group 1.
● Front MODE key is pressed in LEVEL2 of setting group 2,
it returns to previous LEVEL1.
● When season switching selection is changed from OFF
to ON or ON to OFF, previous set weekly program will be
deleted.

N-88
LE7M-2
SUN MON TUE WED THU FRI SAT
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
6:10
PM
6:10
PM
6:10
PM
6:10
PM
6:10
PM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
ON for 10 sec
8:00 AM
Weekly program setting
● Weekly ON/OFF mode
(E.g.) Output 1 (OUT1) is ON from Monday to Friday at 8:00
AM and OFF at 6:10 PM.
● Weekly pulse mode
Output 2 (OUT2) is ON for 10 sec at 8:00AM from Monday
to Friday during S2 season in case, period of S1, S2, S3,
S4 is set.
① Advance to program 1 (P1) weekly program
setting mode
MODE key is pressed over 3
sec in RUN mode, PROG
P1 ashes and press SET
key.
SUN MON TUE WED THU FRI SAT
②Mode type setting
Press SET key in ON/OFF
mode.
SUN MON TUE WED THU FRI SAT
③ ON day setting
Press key to move the
indicator to Monday, it will
be lighted when or key
are pressed and move it to
Tuesday by key.
Press SET key after
Tuesday, Wednesday,
Thursday, Friday turn ON.
SUN MON TUE WED THU FRI SAT
④ ON time setting (AM, PM)
key is pressed, move the
ashing to hour position and
select PM by or key
when ON time is afternoon.
SUN MON TUE WED THU FRI SAT
⑤ ON time setting (hour, min)
Set 8:00 by or key
and press SET key.
SUN MON TUE WED THU FRI SAT
⑥ OFF day setting
Press SET key to check
ON/OFF day.
SUN MON TUE WED THU FRI SAT
⑦ OFF time setting (AM, PM)
Select PM by or key
and move the ashing to
hour position by key.
SUN MON TUE WED THU FRI SAT
⑧ OFF time setting (hour, min)
Move the ashing to minute
position after set 6:00 by
or key and set the minute
as 10 and press SET key.
SUN MON TUE WED THU FRI SAT
⑨ Complete to set
Press SET key to set
additional program.
SUN MON TUE WED THU FRI SAT
① Program 2 (P2) advance to weekly program
setting mode
MODE key is pressed for 3
sec in RUN mode, PROG
P1 is ashed and press
MODE key again, PROG P2
ashes and press SET key.
SUN MON TUE WED THU FRI SAT
② Mode type setting
Press or key when
ON/OFF ashes, Pulse
ashes and press SET
key.
SUN MON TUE WED THU FRI SAT
③ Season selection
Press or key to select
season S2 and press SET
key.
SUN MON TUE WED THU FRI SAT
SUN MON TUE WED THU FRI SAT

N-89
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(J)
Temperature
Controllers
(K)
SSRs
(L)
Power
Controllers
(M)
Counters
(N)
Timers
(O)
Digital
Panel Meters
(P)
Indicators
(Q)
Converters
(R)
Digital
Display Units
(S)
Sensor
Controllers
(T)
Switching
Mode Power
Supplies
(U)
Recorders
(V)
HMIs
(W)
Panel PC
(X)
Field Network
Devices
Weekly/Yearly Timer
④ ON day setting
Press key to move the
indicator to Monday, it will
be lighted when or key
is pressed and move it to
Tuesday by key.
Press SET key after light
Tuesday, Wednesday,
Thursday and Friday.
SUN MON TUE WED THU FRI SAT
Press key, move the
ashing to hour position
and select PM by or
⑤ ON time setting (AM, PM)
SUN MON TUE WED THU FRI SAT
Set 8:00 by or key
and press SET key.
⑥ ON time setting (Hour, Min)
SUN MON TUE WED THU FRI SAT
Press or key to select
pulse duration as 10s and
press SET key.
⑦ Pulse width setting
SUN MON TUE WED THU FRI SAT
Press SET key to set
additional program.
⑧ Complete to set
SUN MON TUE WED THU FRI SAT
6:00 AM
Start Cycle mode
5:30
PM
ON for 10 min
OFF for 5 min
● Weekly cycle mode
(E.g.) Output 1 (OUT1) is ON for 10min and OFF for 5 min
from Monday 6:00 AM to Saturday 5:30 PM.
SUN MON TUE WED THU FRI
SAT
① Advance to program 1 (P1) weekly program
setting mode
In RUN mode, press MODE
key for 3 sec and PROG P1
ashes. Press SET key.
SUN MON TUE WED THU FRI SAT
③to⑧
Refer to ③to⑧ of "●Weekly ON/OFF mode" to set ON
day, ON time, OFF day and OFF time.
② Mode type setting
Press or key when
ON/OFF ashes, CYCLE
ashes and press SET key.
SUN MON TUE WED THU FRI SAT
⑨ ON time width setting
Press key to move the
ashing to minute position
and set as 10 min by or
key and press SET key
SUN MON TUE WED THU FRI SAT
⑩ OFF time width setting
Press key to move the
ashing to minute position
and set as 5 min by or
key and press SET key.
SUN MON TUE WED THU FRI SAT
⑪ Complete to set
Press SET key to set
additional program.
SUN MON TUE WED THU FRI SAT

N-90
LE7M-2
Yearly holiday mode
It operates to o󰀨 the output without program adjustment
during previously set yearly holiday period available from
present year to 31, Dec. of the next year.
Designate the start date of yearly holiday and year of end
date as every year [--] to repeat the holiday mode for
specied in every year.
● Setting example
Set every year 5, May to o󰀨 the output (OUT1, OUT2).
① Advance to weekly day change mode
Press MODE key over 3
sec to move to the setting
group1 in RUN mode and
press it repeatedly until cDY
is ashed in second display
part and press SET key.
SUN MON TUE WED THU FRI SAT
Press key until month
position ashes and set
May by or key and
press key until date
position ashes. Press SET
key after set 5th by key.
③ Start date of yearly holiday setting
SUN MON TUE WED THU FRI SAT
The ashing is moved to
month position directly and
press or key to set
May and press key until
date position ashes.
Press SET key after set 5th
by or key.
④ End date of yearly holiday setting
SUN MON TUE WED THU FRI SAT
Press MODE key to nish the
additional yearly holiday
setting and press SET key
to set .
※It is able to set yearly
holiday up to 12 times.
⑤ Complete to yearly holiday
SUN MON TUE WED THU FRI SAT
② Standard day selection
Press key to move the
indicator to Saturday and
press SET key. after select
Saturday as standard day
(SAT turns ON) by or
key.
SUN MON TUE WED THU FRI SAT
③ Change day selection
Press key to move
the indicator to Monday
and select Monday to
change (MON turns ON)
by or key and repeat
the procedure to select
Tuesday to change (TUE
turns ON) and press SET
key to complete.
SUN MON TUE WED THU FRI SAT
①Advance to yearly holiday mode
Press MODE key over 3secto
move to the setting group1
in RUN mode and press it
repeatedly until hDY ashes
in second display part and
press SET key.
SUN MON TUE WED THU FRI SAT
② Yearly holiday number display
Press SET key after check
yearly holiday number.
SUN MON TUE WED THU FRI SAT
Weekly day change
It operates when the specied day mode is required
to install in other day from the set day and it returns to
previous program setting automatically when it is nished.
It is applied to program 1 (P1) and program 2 (P2).
● Weekly day change cancellation
①Change current year, month, date in current time setting
mode
②Change standard day
③Delete all program in program 1 (P1) and program 2 (P2)
④Season switching
● Setting example
Output 1 (OUT1) is ON in Saturday at 9:00 AM and OFF at
12:00 PM and it is ON 8:30 AM and OFF at 6:00 PM from
Monday to Friday and the mode of Monday and Tuesday is
operated temporarily as Saturday (standard) program.

N-91
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(J)
Temperature
Controllers
(K)
SSRs
(L)
Power
Controllers
(M)
Counters
(N)
Timers
(O)
Digital
Panel Meters
(P)
Indicators
(Q)
Converters
(R)
Digital
Display Units
(S)
Sensor
Controllers
(T)
Switching
Mode Power
Supplies
(U)
Recorders
(V)
HMIs
(W)
Panel PC
(X)
Field Network
Devices
Weekly/Yearly Timer
② Mode type setting
or key is pressed when
ON/OFF ashes to set
pulse mode and press SET
key.
SUN MON TUE WED THU FRI SAT
③ Start date setting
Press or key twice
to set 08 (year 2008) and
move to month position by
key.
Set Oct. by or key and
move to date position by
key and press SET key
after set 2nd by or key.
SUN MON TUE WED THU FRI SAT
④ End date setting
The ashing is moved to
month position directly by
key and set 4th by or
key after move it to date
position by key, then
press SET key.
SUN MON TUE WED THU FRI SAT
④ End date setting
The ashing is moved to
month position directly and
press or key to set
April and press or key
until date position ashes.
Press key after set 7th by
SET key.
SUN MON TUE WED THU FRI SAT
⑤ ON time setting (AM, PM)
key is pressed, move the
ashing to hour position
and select PM by or key
when ON time is afternoon.
SUN MON TUE WED THU FRI SAT
⑥ ON time setting (hour, min)
Press or key to set 9
and press SET key after
check 00min
SUN MON TUE WED THU FRI SAT
⑦ OFF time setting (AM, PM)
Select PM by or key
and move the ashing to
hour position by key.
SUN MON TUE WED THU FRI SAT
⑧ OFF time setting (hour, Min)
Move the ashing to minute
position after set 5:00 by
or key and set the minute
as 10 and press SET key.
SUN MON TUE WED THU FRI SAT
⑨ Complete to set
Press SET key to set
additional program.
SUN MON TUE WED THU FRI SAT
2, Oct 3, Oct 4, Oct
8:00
AM
8:00
AM
8:00
AM
ON for 5 sec
10:00AM
● Yearly pulse mode
(E.g.) Output 2 (OUT2) is ON from 2, Oct, 2008 to 4, Oct,
2008 at 10:00 AM and OFF after 5 sec (present is
2007.)
① Advance to program 2 (P2) yearly program
setting mode
MODE key is pressed for 3
sec in RUN mode, PROG
P1 is ashed and press
MODE key again, PROG P2
YEAR is ashed and press
SET key.
SUN MON TUE WED THU FRI SAT
Yearly program setting
● Yearly ON/OFF mode
(E.g.) Output 1 (OUT1) is ON from every 5, Apr to 7, Apr at
9:00 AM and OFF 5:10 PM.
① Advance to program 1 (P1) yearly program
setting mode
Press MODE key for 3 sec
in RUN mode, PROG P1 is
ashed and press MODE key
3 times more until PROG
P2 YEAR ashes and press
SET key.
SUN MON TUE WED THU FRI SAT
②Mode type setting
Press SET key when ON/
OFF ashes.
SUN MON TUE WED THU FRI SAT
③ Start date setting
Press key until month
position ashes and set April
by or key and press
key until date position
ashes. Press SET key after
set 5th by or key.
SUN MON TUE WED THU FRI SAT

N-92
LE7M-2
RUN mode
Program 1 Yearly program
record No.1 [r01]
setting check
Program 1 Yearly program
record No.1 [r01] setting
modify and delete
Program 1 Yearly program
record No.2 [r02] setting
modify and delete
Program 2 Yearly program
record No.1 [r01] setting
modify and delete
Program 1 Yearly program
record No.2 [r02]
setting check
Program 2 Yearly program
record No.1 [r01]
setting check
CHECK
CHECK
CHECK
Yearly program check, modify and delete
※YEAR turns ON when check, modify or delete yearly
program.
● If any key is untouched for 60 sec, it is returned to RUN
mode in weekly or yearly program check.
● In weekly or yearly program check, it controls output
according to program setting and output is OFF in
modify or delete mode.
● When MODE key is pressed in weekly or yearly program
record modify, delete stand by or delete mode, current
work is canceled and it is returned to check mode.
● Weekly or yearly program record modify and delete
(1) Program record modify
①When press SET key over 3 sec in program check, EDT
ashes in second display part, press SET key.
②It returns to check mode when nish the modify same
as the above procedure.
(2) Program record delete
①When press SET key over 3 sec in program check, EDT
ashes in second display part, press or key until
CLR ashes in second display part and press SET key.
②Press CLR key over 3 sec when SET turns ON in second
display part, it returns to program check.
RUN mode
Program 1 weekly program
record No.1 [r01]
setting check
Program 1 weekly program
record No.1 [r01] setting
modify and delete
Program 1 weekly program
record No.2 [r02] setting
modify and delete
Program 2 weekly program
record No.1 [r01] setting
modify and delete
Program 1 weekly program
record No.2 [r02]
setting check
Program 2 weekly program
record No.1 [r01]
setting check
Program Check, Modify And Delete
Press CHECK
key for 1 sec
CHECK
CHECK
CHECK
Weekly program check, modify and delete
Press
MODE
key
for 3 sec
Press SET
key for 3 sec
Press SET
key for 3 sec
Press SET
key for 3 sec
Press CHECK
key for 1 sec
Press
MODE
key
for 3 sec
Press SET
key for 3 sec
Press SET
key for 3 sec
Press SET
key for 3 sec
※It is able to set year of start/end date in yearly program
setting up to 2 years later from the present year.
key is pressed, move the
ashing to hour position and
select PM by or key
when ON time is afternoon.
⑤ ON time setting (AM, PM)
SUN MON TUE WED THU FRI SAT
⑧ Complete to set
Press SET key to set ad-
ditional program.
SUN MON TUE WED THU FRI SAT
⑦ Pulse width setting
Press or key 4 times
to select pulse width as 5s
and press SET key.
SUN MON TUE WED THU FRI SAT
⑥ ON time setting (hour, Min)
Press or key twice to
set 10 and press SET key
after check 00 min
SUN MON TUE WED THU FRI SAT