AV TOOL AVT-1660 User manual

Instruction Manual
AVT-1660
Standards Converter

1

2
Table of Contents
1.0 Introduction 3
2.0 General Instructions 4
3.0 Intellectual Property 5
4.0 Specifications 5
5.0 Package Contents 5
6.0 Connecting the Hardware 6
7.0 Operating The Unit 6
8.0 Troubleshooting 7
9.0 Limited Warranty 8
10.0 Regulatory Compliance 9
11.0 Contact Information 9

3
1.0 INTRODUCTION
Thanks for purchasing this AVT-1660 Standards Converter from AV Toolbox.
The AVT-1660 is designed to transform one television signal format to another
through the use of sophisticated digital line and field conversion techniques. Our
Video conversion products have been serving the industry for many years. AV
Toolbox offers a full line of high quality Standards Converters, Up-Converters,
Scan Converters, Distribution Amplifiers, Routing Switchers, Time Base
Correctors, PIP Display Devices, Quad Splitters and Video Conditioners. RF
Modulators, Digital Audio Converters, LCD Monitors/Receivers and Multimedia
Cables round out the product offerings.
1.1 Liability Statement
Every effort has been made to ensure that this product is free of errors. AV
Toolbox cannot be held liable for the use of this hardware or any direct or indirect
consequential damages arising from its use. It is the responsibility of the user of
the hardware to check that it is suitable for his/her requirements and that it is
installed correctly. All rights reserved. No parts of this manual may be
reproduced or transmitted by any form or means electronic or mechanical,
including photocopying, recording or by any information storage or retrieval
system without the written consent of the publisher.
AV Toolbox reserves the right to revise any of its hardware and software
following its policy to modify and/or improve its products where necessary or
desirable. This statement does not affect the legal rights of the user in any way.
All third party trademarks and copyrights are recognised. The AV Toolbox Logo,
TV One Logo, TV One-Task and CORIO are the registered Trademarks of TV
One. All other trademarks are the property of their respective holders.
1.2 FEATURES
The AVT-1660 Standards Converter has many features that enable it to perform
in a superior manner. Among those features you will find:
Composite Video and S-Video Inputs
Composite and S-Video Outputs
Automatic Detection of Input Signal Type
Multi Video Standards Supported
6 mb Field Memory
Built in Color Bar Generator
Automatic Gain Control
Small Size – Light Weight

4
2.0 IMPORTANT SAFETY INSTRUCTIONS
To insure the best from this product, please read this manual carefully. Keep it in
a safe place for future reference.
To reduce the risk of electric shock, do not remove the cover from the unit.
No user serviceable parts inside. Refer servicing to qualified personnel.
2.1 POWER AND CONNECTIONS
This unit is not disconnected from the AC power source as long as it is
connected to the wall outlet. The off state for this unit is called standby mode. In
standby mode the unit is designed to consume a reduced quantity of power
compared to normal operating modes.
When not using the unit for a long period of time, insure that the AC power cord
is disconnected from the wall outlet.
The AC wall outlet should be installed near to the unit and be easily accessible.
Do not plug in or attempt to operate an obviously damaged unit.
2.2 WATER AND MOISTURE
To reduce the risk of fire, do not expose the unit to rain, water or excessive
moisture.
2.3 GENERAL CARE
Do not force switches or external connections. When moving the unit,
disconnect the serial port connections first then the power cable and finally the
interconnecting cables to other devices. o not attempt to clean the unit with
chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean
dry cloth.
2.4 LOCATION
Installation of this unit should be in a cool dry place, away from sources of
excessive heat, vibration, dust, moisture and cold.
2.5 VENTILATION
Slots and openings in the sides of the unit are provided for ventilation. To insure
reliable operation, avoid obstruction of these openings and insure the unit is
installed in a well-ventilated area.

5
3.0 INTELLECTUAL PROPERTY
Some IC chips in this product include confidential and/or trade secret property.
Therefore you may not copy, modify, adapt, translate, distribute, reverse
engineer, reverse assemble, or decompile the contents thereof.
4.0 SPECIFICATIONS
Video Inputs
Composite Video 1x via RCA Connector
S-Video (Y/C) 1x via 4-PIN Mini-DIN Connector
Video Outputs
Composite Video 1x via RCA Connector - NTSC 3.58 & PAL
S-Video (Y/C) 1x via 4-PIN Mini-DIN Connector - NTSC 3.58 & PAL
Video Standards Supported
NTSC NTSC 3.58, NTSC 4.43
PAL PAL B,D,G,I,K plus PAL-M and PAL-N
SECAM (Input Only – Output must be NTSC 3.58 or PAL)
Video Signal Controls/Test Signals
Manually Adjustable CV/SV Input Selection, NTSC/PAL Output Selection
Test Signals Color Bar Signal Output (When no input present)
Physical
Size 1.77” H x 9.3” W x 5.1” D (45x236x130mm)
Weight 14 Ounces (0.4kg)
Power
AC Adapter 115 VAC to 5[email protected]
5.0 CHECKING PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make certain
the following items are contained in the shipping carton:
AVT-1660 Standards Converter
115 VAC to +5VDC Power Adapter
Operation Manual
Note: Please retain the original packing material should the need ever arise to
return the unit. If you find any items are missing, contact your reseller or AV
Toolbox immediately. Have the Model Number, Serial Number and Invoice
available for reference when you call.

6
6.0 CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input,
outputs, power requirements plus any controls present.
Connect the AC to +5VDC adapter to an AC source and then to the DC power
input shown on the right side of the lower drawing above. (Note that there is no
power switch. The unit will begin to function as soon as you have the AC to
+5VDC adapter plugged in and furnishing power).
Next connect an input cable and an output cable to either the Composite Video
or S-Video connectors as desired. (Note that you can connect both Composite
and S-Video cables to the input connectors but you cannot use both at the same
time. You must select one or the other for the signal conversion process using
the input select switch. V equals Composite Video and S equals S-Video.)
7.0 OPERATING THE UNIT
Operation of the AVT-1660 operation is for the most part automatic. The type of
television signal is automatically detected and the conversion process is also
automatic.
Manual intervention is limited to selecting either the Composite or S-Video
connector as the input source and selecting NTSC 3.58 or PAL as the output
type using the Input and Output switches. Once you’ve made those selections,
the front panel LEDs will indicate the input connector you’ve selected, the output
format you’ve selected and the type of input signal that the AVT-1660 has
detected. (Note that in the event of no input signal, the AVT-1660 will output
Front Panel LED Display
Rear Panel Connectors & Controls

7
Color Bars in either NTSC 3.58 or PAL formats depending on the output type
selection made.)
Please refer to the front panel LED drawing above for the discussion that follows.
7.1 Initial Power Up
When power is applied, the AVT-1660 will default to the auto detect mode and
select the proper Television Standard. The meaning of the abbreviations below
the LEDs areas follows:
SECAM SECAM Standard
PAL PAL
PM PAL-M
PN PAL-N
N4 NTSC 4.43 Mhz
N3 NTSC 3.58 Mhz
As an example of how the auto-detect works, if you live in the United States or
Japan, the detected input will be the NTSC 3.58 Standard and the unit will light
the “N3” LED. If you live in the United Kingdom, the standard will be PAL so the
“PAL” LED will light. In France, Russia and certain other countries, the SECAM
LEDs will light. Some countries use variants of these basic systems and if the
signal is one of these variants, an LED will light indicating the input signal type
that is being converted.
7.2 Input and Output LEDs
On the left of the Front Panel LED display matrix, two LEDs indicate which type
of signal, Composite or S-Video, you have selected with the rear panel input
switch. Similarly, on the right, two more LEDs indicate which output type you
have selected, NTSC or PAL.
8.0 TROUBLESHOOTING
Most problems with the AVT-1660 are related to misuse of the two switches and
defective cables. If you find that the picture is not acceptable, make certain that
the unit is receiving power and then check the position of the two switches on the
rear of the unit. Remember that you can only use one of the two possible input
connections at a time. Next, inspect the cables for loose connectors or cable
damage such as crushed cables or cables with cuts or nicks. Replace any cable
exhibiting these problems. (Note that you also must use the highest quality
cables if you want to achieve the best results. Poor quality cables will cause poor
quality signals.)
After trying the above suggestions should the problem still persist, contact your
dealer for additional suggestions before contacting AV Toolbox. Should the

8
dealer’s technical personnel be unable to assist you, contact AV Toolbox via our
parent company’s support website: http://tvone.crmdesk.com. Create a
technical support request on the site and our support team will respond within a
short period of time.
9.0 LIMITED WARRANTY
LIMITED WARRANTY – With the exceptions noted in the next paragraph, AV
Toolbox warrants the original purchaser that the equipment it manufactures or
sells will be free from defects in materials and workmanship for a period of one
year from the date of purchase. Should this product, in AV Toolbox’s opinion,
prove defective within this warranty period, AV Toolbox, at its option, will repair or
replace this product without charge. Any defective parts replaced become the
property of AV Toolbox. This warranty does not apply to those products which
have been damaged due to accident, unauthorized alterations, improper repair,
modifications, inadequate maintenance and care, or use in any manner for which
the product was not originally intended.
Items integrated into AV Toolbox products that are made by other manufacturers,
notably computer hard drives and liquid crystal display panels, are limited to the
term of the warranty offered by the respective manufacturers. Such specific
warranties are available upon request to AV Toolbox. If repairs are necessary
under this warranty policy, the original purchaser must obtain a Return
Authorization Number from AV Toolbox and return the product to a location
designated by AV Toolbox, freight prepaid. After repairs are complete, the
product will be returned, freight prepaid.
LIMITATIONS - All products sold are "as is" and the above Limited Warranty is in
lieu of all other warranties for this product, expressed or implied, and is strictly
limited to one year from the date of purchase. AV Toolbox assumes no liability to
distributors, resellers or end-users or any third parties for any loss of use,
revenue or profit.
AV Toolbox makes no other representation of warranty as to fitness for the
purpose or merchantability or otherwise in respect of any of the products sold.
The liability of AV Toolbox with respect to any defective products will be limited to
the repair or replacement of such products. In no event shall AV Toolbox be
responsible or liable for any damage arising from the use of such defective
products whether such damages be direct, indirect, consequential or otherwise,
and whether such damages are incurred by the reseller, end-user or any third
party.
10.0 REGULATORY COMPLIANCE
The AVT-1660 has been tested for compliance with appropriate FCC and CE
rules and regulations. The Power Adaptor/Supplies have been tested for

9
compliance with appropriate UL, CUL, CE, PSE, GS Rules, Regulations and/or
Guidelines. These Products and Power Adapters are RoHS Compliant.
11.0 CONTACT INFORMATION
Should you have questions or require assistance with this product in areas not
covered by this manual, please contact TV One at the appropriate location.
AV Toolbox USA
2791 Circleport Drive
Erlanger, KY 41018
USA
Tel [phone]
Tel [phone]
Fax [phone]
[email protected]
www.avtoolbox.com
AV Toolbox Europe
Continental Approach
Westwood Industrial Estate
Margate, Kent CT9 4JG, UK
Tel [phone]
Fax [phone]
[email protected]
www.avtoolbox.com
AV Toolbox Latin America
6991 NW 82nd Avenue #8
Miami, FL 33166
USA
Tel [phone]
Fax [phone]
[email protected]
www.tvonela.com
AV Toolbox Mercosur
Av. Diaz Velez 3965 #PB
(1200) Capital Federal
Buenos Aires, Argentina
Tel [phone]
Fax [phone]
[email protected]
www.tvonela.com
AV Toolbox Asia
16F-4, No.75, Sec.1
Hsin Tai Wu Rd., Hsichih
Taipei Hsien 22101
Taiwan R.O.C.
Tel [phone]
Fax [phone]
[email protected]
www.tvoneasia.com
AV Toolbox China
Room 1007, Golden Peach Building
No. 1900 Shangcheng Road
Pudong, Shanghai
China 200120
Tel [phone]
Fax [phone]
[email protected]
www.tvoneasia.com
End of Manual