Avent Security VN168 User manual

VN168
Digital Door Lock

Brief Introduction
Battery
Keypad
Card Reader
Cylinder
1
1
2
There are 1 master password user, 50 password users and 200 card users available in the lock.
The default master password is “1234-5678”. New Lock only has master password, people only
can input the master password to unlock.
3The master password has to be 8 digits, while the normal password has to be 6 digits.
4The Micro-USB port is used as the emergency power port.
5There are 2 unlocking modes in the lock:
a) Single Unlocking Mode: each time the lock only needs 1 registered user for unlocking;
b) Double Unlocking Mode: each time the lock needs 2 registered users for unlocking.
These 2 registered users have to be 1 password user and 1
card user.
123
45 6
789
*0#
Micro-USB Port

Installation
Fr on t
Si de
Fo ld
Fo ld
1.Drill the holes on the door according
to the template;
2. Install the mortise into the door,
and fasten the screws;
3.Install the cylinder into the mortise,
and then install the cover on the
mortise. Insert the spindle into the
mortise.
4.Install the front panel on the door,
connect the cable with the mortise
cable;
5.Insert the spindle and the deadbolt
spindle into another side of the
mortise
6.Install the back panel on the door,
and fasten the screws
7.Connect the power cable with the
battery case
8.Try to unlock the lock and confirm
the installation is correct.
2

123
45 6
789
*0#
Operation
Touch the keypad to activate the lock, and then input the password with press “#” to finish. If the
password is correct, the LED indicator shows blue light with sounds, and then you can press down
the handle for unlocking.
“BLUE”
1Password Unlocking
+
3
*** #
+
If you input a wrong password for 5 times, the lock will be locked for 5
minutes. During the 5 minutes, the lock cannot be activated and all operations
are not available. After that, the lock returns to normal state.
Random Password Protection
For a better security protection to the password user, the lock is designed with a random
password protection. You can add any digits before and after the real password.
For example, the password is “123-456”, you can unlock the lock by inputting the password
as following:
1:
2:
3:
X X X X X X 1 2 3456
1 2 3456X X X X X X
X X X X 1 2 3456X X
#
#
#
XX

123
45 6
789
*0#
When there are problems with electronic part, and the batteries run out of power
using mechanical key is the way to unlock the lock.
Take out the cylinder cover, and then insert the mechanical key into the cylinder,
then turn the key to unlock.
3Mechanical Key Unlocking
4
RF Card Unlocking
2
Place the card close to keypad. If the card is correct, the LED indicator shows blue light
with sounds, and then you can press down the handle for unlocking.
“BLUE”
+
123
45 6
789
*0#

The master password has to be 8 digits.
5
Change Master Password
4
Input master password,
press # to confirm;
(default password is 1234-5678)
a
Master
*** #
+
1
Input 1
b
Input new master password,
press # to confirm;
c
NEW
*** #
+
Input new master password again,
press # to confirm, and then finish
the registration.
d
NEW
*** #
+
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.

The password has to be 6 digits;
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.
6
3Add Users (Password User)
5
Input Master Password,
press # to confirm;
a
Master
*** #
+
8
Input 8
b
Input new password,
press # to confirm;
c
*** #
+
dInput new password again,
press # to confirm, and then
finish the registration.
#
+
***

7
3Add Users (Card User)
6
Input Master Password,
press # to confirm;
a
Master
*** #
+
8
Input 8
b
Place the card on the card reader
and finish the registration.
c
If the deadbolt comes out when registering, the card can unlock
when the deadbolt is open.
It is suggested to make a list for recording the card user ID.
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.

3Delete All Users (Password and Card)
8
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.
Input Master Password,
press # to confirm;
a
0
Input 0
bThe lock starts to delete
all normal users.
c
#
8
3Delete Single User (Password or Card)
7
a
4
Input 4
b
Input Master Password,
press # to confirm;
#
+
Master
***
Input the password (or Card)
you want to delete, and the
system will delete it.
c
***
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.
or
Master
*** #
+

Modify Password
9
Input Old Password,
press # to confirm;
a
OLD
*** #
+
1
Input 1
b
dInput new password again,
press # to confirm, and finish.
#
+
***
NEW
Input new password,
press # to confirm;
c
#
+
***
NEW
The password has to be 6 digits.
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.
3Delete the Lost Card
10
aInput Master Password,
press # to confirm; bInput 3
3
cInput the card before
the lost card to delete
the lost card, and finish.
9
It is suggested to make a list for recording the card user ID
If the ID of the lost card is the last one, please use the card in first ID to delete it.
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.
Master
*** #
+

Unlocking Mode
11
When the lock is requested for unlocking frequently, you can activate the passage mode
and let the people unlocking without identifications.
10
Single Unlocking Mode to Double Unlocking Mode
a
6
Input 6, press # to confirm,
and finish.
b
Input master password,
press # to confirm;
#
+
Master
*** #
+
Each time the lock needs to input 1 registered user for unlocking.
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.
Double Unlocking Mode to Single Unlocking Mode
aInput 5, press # to confirm,
and finish.
b
Input master password,
press # to confirm;
#
+
Master
*** 5#
+
Each time the lock needs to input 2 registered users for unlocking.
These 2 users have to be 1 password user, and 1 card user.
Once finish the operations, please try to unlock the lock to confirm the operation
is successful.

11
aPlace an unlocking card on the reader to unlock,
and then the lock returns to normal state.
Disable:
3Passage Mode
12
aKeep retracting the latch bolt,
and then place an unlock card
on the reader when the lock has an alarm
b
Press down the inside handle
and retract the latch bolt.
Enable:
When the lock is requested for unlocking frequently, you can activate the passage mode and let the people
unlocking without identifications.
3Restore the Lock
13
When the lock has problems and you can try to restore the lock to solve the problems.
Insert the key into the cylinder and turn the key to retract the latch, hold it for 20 seconds and release it
when hearing the lock sounds.
X 20S