Avent Security M500 User manual

M500
FINGERPRINT DOOR LOCK

1
Installation
Drill the holes on the door and then
install the mortise into the door;
aInstall the spindle into the handle hole
in the front panel, and then insert the
rod and fasten it;
b
Install the front panel on the door
cConnect the cable between the front
and back panels
d
Install the back panel on the other
side of door, and then fasten both
panels and install the batteries.
eTest the installation to confirm the
installation is successful.
f

2
1. The default master password is “123-456”;
2. There are total 300 users available, 9 users are the master users,
291 are the normal users normal users in the lock;
3. The password can be 6 to 8 digits;
4. The micro-USB port is at the bottom of front panel, which is the port for emergency power supply;
5. The lock has 2 unlocking modes: Single Unlocking Mode and Double Unlocking Mode.
Product Guide
Brief Introduction
E-Deadbolt
Fingerprint Sensor
Keypad
Battery Case
Cylinder
Micro-USB Port
Card Reader

Operation
Register Master User
1
Input * + #
a
Input 1 for master user
cInput 1 to register master user
d
Input the master user for authorization,
press # to confirm
b
Fingerprint: place the
fingerprint on the sensor
for 3 times to register
ePassword: input the
password, and press #
to confirm in 2 times
fCard: place the card
close to the card
reader to register.
g
The master password can be 6 to 8 digits;
For new lock, the default master password is “123-456”.
When a new master user is registered in the lock, this default password is deleted automatically.
There are up to 9 master users available in the lock.
It is suggested to make a list to record the users’ ID numbers for a better management.
Once finishing the operations, please try to unlock the lock to confirm the operation is successful.
3
X4

Add Normal User
2
Input * + #
a
Input 2 for normal user
cInput 1 to register normal user
d
Input the master user for authorization,
press # to confirm
b
Fingerprint: place the
fingerprint on the sensor
for 4 times to register
ePassword: input the
password, and press #
to confirm in 2 times
fCard: place the card
close to the card
reader to register.
g
The master password can be 6 to 8 digits;
There are up to 291 normal users available in the lock.
It is suggested to make a list to record the users’ ID numbers for a better management.
Once finishing the operations, please try to unlock the lock to confirm the operation is successful.
4
X4
2

Delete Master User
3
Input * + #
a
Input 1 for master user
cInput 2 to delete master user
d
Input the master user for authorization,
press # to confirm
b
Input the ID number you want to delete,
press # to confirm
e
The master user which is used to log in the system can not be deleted.
Once finishing the operations, please try to unlock the lock to confirm the operation is successful.
5
2
ID

Delete Normal User (Single User)
4
Input * + #
a
Input 2 for normal user
cInput 2 to delete single normal user
d
Input the master user for authorization,
press # to confirm
b
Input the ID number you want to delete,
press # to confirm
e
Once finishing the operations, please try to unlock the lock to confirm the operation is successful.
6
ID
2 2

Unlocking Mode
5
Input * + #
a
Input 3 for system setting
cInput 2 for unlocking mode
d
Input the master user for authorization,
press # to confirm
b
Once finishing the operations, please try to unlock the lock to confirm the operation is successful.
When the lock is under double unlocking mode, you have to input 2 registered users to unlock every time.
The master users can unlock directly even the lock is under double unlocking mode.
7
3
Sometimes if you need a higher security level, you can set up the lock in double unlocking mode,
which the unlock needs 2 registered users for unlocking each time.
Single unlocking: input 1
eDouble unlocking: input 2
f
2
1 2

Voice Setting
6
Input * + #
a
Input 3 for system setting
c
Input the master user for authorization,
press # to confirm
b
8
Input 1 for voice setting
d
You can turn on/off the voice for unlocking
Input 1 to turn on the voice
e
1
Enable:
Disable:
Input * + #
a
Input 3 for system setting
c
Input the master user for authorization,
press # to confirm
b
Input 1 for voice setting
d
1
Input 1 to turn on the voice
e
2
Once finishing the operations, please try to unlock the lock to confirm the operation is successful.
3 1
3

Passage Mode
8
Activate the lock and then input 5 + #
ab
Enable:
Input the registered user to unlock and
the lock will be under passage mode.
When the lock is required to unlock frequently, set the lock to passage mode can let the
people unlock the lock without any identification.
Time Setting
7
8
The format for the date and time is 2 digits, which is Year (XX) – Month (XX) – Day (XX) -Hour (XX)
– Minute (XX). For example: March 21th, 2019 at 13:45 is 1903211345.
Input * + #
a
Input 3 for system setting
c
Input the master user for authorization,
press # to confirm
b
3
Input 4 for time setting
dInput the new date and time
to the lock.
e
time
ID
4
5

9
Disable:
a
Restore The Lock
9
When the lock has problems and you can try to restore the lock to solve the problems.
Activate the lock and then input 5 + #
to cancel the passage mode.
5
aPress the reset key in the battery case for 6 seconds, and then the lock will be restored to the factory default.
The master password will be restored to “123-456”.
Input * + #
aInput the master user for authorization,
press # to confirm
b
Input 4 to restore the lock
c
Option # 1
Option # 2
4
SE T