AVF Group 469193 User manual

45kg
99lb
STOP
Read through ALL instructions before commencing installation.
If you have any questions about this product or issues with installation, contact
the customer services helpline before returning this product to the store.
This TV Wall Mount is intended for use with televisions weighing Maximum
. Use with products heavier than maximum weight may
result in instability causing possible injury.
45kg (99lbs)
AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
469193 rev02
jl.avfgroup.com
0333 320 0463 (UK)
CUSTOMER SERVICES HELPLINE NUMBER:

Assembly Overview
Fit the Wall Rail
Solid Wall
Wood Stud
Suitable Wall Types
Marking Wall for Drill Points
Hang the TV
Fit the TV Brackets
Use Height Calculator result to position these drill holes
When mounting to a solid wall,
attach the wall plate using all four holes marked
JXPL401 469195

Index
Preparing the TV Brackets
2
Fitting the TV Brackets
3
Marking Wall for Drill Points
4
Fitting the Wall Rail
5
Measure the TV fixing holes Width and Height
1
Retain all packaging in case the product needs to be returned.
Contents may vary from photography / illustrations.
You will not need all these parts, so expect there to be some left over depending upon the
specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead to
failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of a suitable
standard and void of any services (eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing this product in a
substandard wall.
Fitting the Wall Rail Covers
6
Hide the TV Release Cords
8
Hide the TV Return Straps
10
Return the TV to the Wall
9
Hanging the TV
7

Ø3mm (1/8”)
Wood
Ø10mm (25/64”)
Masonry
Stud Finder
Tools Recommended
TV Screws, Reducers and Spacers
M4
16mm
F1x4
M4
25mm
F2x4
M6
25mm
F6x4
E1x12 E2x4
D1x4 D2x4
M8
25mm
F9x4 F4x4
M5
16mm
F5x4
M6
16mm
F7x4
45mm
M6
F8x4
M8
16mm
F10 x4
M8
45mm
F3x4
M4
45mm

Boxed Parts
C
Hx4 Gx4
B1
B1
C
I
TV Return Strap
TV Release Cord
A
Use Height Calculator result to position these drill holes
When mounting to a solid wall,
attach the wall plate using all four holes marked
JXPL401 469195
WT
B2
B2

If width Xis greater than 400mm or height Ygreater than 400mm
STOP installation now and contact the customer helpline
Preparing the TV Brackets
2
Measure the TV fixing holes Width and Height
1
75 - 400mm
75 - 400mm
TV Fixing Holes
F1-F3
M4 =
M6 = F5-F7
M8 = F8-F10
M5 = F4
X
Y
You are provided with 4 diameters
of TV fixing screws M4, M5, M6
and
M8.
Determine the screw diameter that
fits and remember for step 3.
IMPORTANT: Must be done before fitting brackets to your TV.
Loosen the TV Levelling Screw enough so that you can push the
catch up to its maximum height (as shown).

To ensure maximum tilt is possible after installation you will need to ensure that your TV does not
clash with the wall.
Top Bottom
No Clash
Clash
Top Bottom
No Clash
Top Bottom
B1
B2
Click!
Fitting the TV Return Straps

Fitting the TV Brackets
3
TV TV TVTV
No Spacers Spacers
For TVs with irregular / obstructed back.For TVs with flat / unobstructed back.
E1/E2
If your TV has an irregular/obstructed back or if you have any issues fitting to the back of your TV
with the supplied screws, please call the customer services helpline.
WARNING

Attach the brackets to the back of your TV using suitable screw, reducer and spacer combinations.
After completing step you will have fixings left over, please keep for future reference.
3
If required
D1or D2?
Do you need
Top
For easy access to some of the TV fixing holes, follow the procedure on the next page.
E2
F1- F10
E1
D1
F1- F3
F4- F7
F8- F10
D2

Easy Access to TV Fixing Holes
You must fully reassemble the TV Brackets when you have finished fixing them to the
back of the TV.
Disassembly and Reassembly