AVF Group JML8400 User manual

JML8400 Leaflet No. 463448 rev02
AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
80"
203cm
CUSTOMER SERVICES HELP LINE NUMBER:
01952 670009 121lbs
55kg
STOP
Read through instructions before commencing installation.
If you have any questions about this product or issues with installation
contact the customer services helpline before returning this product to
the store. See jl.avfgroup.com/p/jml8400 for more information.
ALL

1Boxed Parts
You will not need all these parts, so expect there to be some left over depending upon the
specification of your TV.
TV Fixings: Parts go on the back of the TV
(specification of your TV will determine
which ones you require - see section 11).
Wall Fixings: Parts to attach to the wall
(type of wall will determine which fixings
you require).
No.14 x 105mm
No.14 x 70mm
No.12 x 25mm
No.8 x 38mm
F1
G1
G4
G7
G10
F2
G2
G5
G8
G11
F3
G3
G6
G9
G12
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
- x4
M4 Adaptor
M4 16mm
M5 16mm
M6 16mm
M8 16mm
M5 Adaptor
M4 25mm
M5 25mm
M6 25mm
M8 25mm
M6 Adaptor
M4 45mm
M5 45mm
M6 45mm
M8 45mm
E1- x12
Spacer H I J
- x4 - x4 - x8
Wall Fixing Long Wall
Plug Lock Nut
K L M
- x4 - x2 - x4
Long Screw Metal Stud
Screw Wall Plug
N O P
- x4 - x2 - x2
Screw Screw Screw Plug Q- x2 Wall Plug
Included Tools
K L M
- x4 - x2 - x4
Long Screw Metal Stud
Screw Wall Plug
R- x1
18mm Wood
Drill
S- x1
3mm Hex
Key
U1- x1
Template U2- x1
A- x1
LH Wall
Bracket
B- x1
RH Wall
Bracket
C- x2
Hanger D- x2 Stand-off
T- x1
Level
E2- x4
Spacer (Red)

2Tools Required
3Determine Correct TV Screw Size
Choose from the TV Fixings selection.
You need to determine which length
and diameter of screws fits your TV.
To determine the correct screw diameter,
try screwing (G2), (G5), (G8) & (G11) into
one of the fixing holes on the back of the
screen until you find the one that fits.
4Fit Screen Hangers To TV
Once you have established which screws you need for your TV, you can attach the Hangers (C)
and Stand-offs (D) to the back of your TV.
Typical recommended example shown is for fixings with the TV spaced 20mm from the wall.
The TV Mount can position your TV between 12mm and 40mm from the wall. For alternative
configurations see section 11.
You might need to use spacers to increase the clearance of your TV from the wall in order to avoid
cables coming out of your TV and improve access and ventilation to the back of your TV (spacers
(E1) allow you to have a gap of 20mm or 40mm, see section 11).
In certain circumstances it may be necessary to use red spacer (E2) as either a replacement or
addition to spacer (E1), for more information please see section 11.
If your TV fixing centres don’t fit, STOP installation and contact the customer services helpline.
G2, 5 ,8, 11
Top Fixings
F1, 2, 3 *If Required
G2, 5 ,8, 11
Bottom Fixings
*
F1, 2, 3
G2, 5 ,8, 11
If using screw use Adapter (F1)(G2)
If using screw (G5) use Adapter (F2)
If using screw (G8) use Adapter (F3)
If using screw (G11) No Adapter required
*
TV must be parallel
to wall. Use spacers /
stand-offs as shown.
C
E1
D
E1

5Assemble Positioning Template
The horizontal part of the positioning template is used to mark out
where you need to drill the mounting holes on your wall. The vertical
part is just a guide to allow you to see how high up the wall your TV
will be to help you find the perfect position for viewing your screen.
Thread template (T2) through template (T1) as shown.
6Determine Bracket Hole Centres
If your screen fixings do not line
up with any holes on the template
then ensure template is on the
centre of the screen, and punch
holes to suit your screen fixings
centres with a pencil or sharp
object.
Line up the template with
the centre of the screen.
Mark off the fixing centres.
Tear off the template flush with the
bottom of your TV so that when
the template is on the wall you can
see exactly where your TV will be
vertically (distance from the floor
and ceiling).
Line up with top of
the screen.
Lay the template on the back of the TV and follow the instructions below.
U1
U2
Line up with top of
the screen.
The centre line of the template
represents the centre of your TV.

7Marking Wall For Drill Points
Use your template to mark two points on the wall that correspond with the top fixing centres of
your TV.
Represents the top
of your TV.
Represents the base
of your TV.
8Planning & Preparation
Determine the wall type that you have (i.e. Brick/Stud/Plasterboard/Sheetrock).
Ensure the drilling area is free from mains services (Gas/Electric/Water).
Drill six 3mm diameter pilot holes to verify the wall type and select the appropriate fixings (See
Section 9).
Represents the
centre of your TV.
T
Next, use the Wall Brackets (A) and (B) as a template
and position it over one of the PENCIL MARKS you
have made, so that the mark is in the middle of the
CENTRAL HOLE of the Wall Bracket (A). Ensure the
bracket is level and mark the three DRILL POINTS with
a pencil. Repeat for both brackets.
Drill points
ADrill points
B
Pencil Mark
Central Hole
T
Represents the
centre of your TV.
BA

9
Install Wall Fixings
Use the correct fixings for your wall type. Mixing fixing types may be required for installations that
span different wall types. DO NOT OVER TIGHTEN SCREWS.
Remove
dust from
holes
Ø18mm
(3/4")
Solid WallDot & DabPlasterboard
/ Sheetrock
Wood StudMetal Stud
108mm
(41/4")
Ø10mm
(25/64")
Remove
dust from holes
40mm Max
(19/16")
If gap is above 40mm use
Plasterboard / Sheetrock fixing method
(19/16")
Ø3mm
(1/8")
Only one fixing will be in the wood stud. The other fixings will be in plasterboard / sheetrock (see above).
Only one fixing will be in the metal stud. The other fixings will be in plasterboard / sheetrock (see above).
Lubricate screw
thread with soap
Lubricate screw
thread with soap
Use Plasterboard /
Sheetrock fixings
Lubricate screw
thread with soap
Hand tighten
only
**Turn until secure
Do not over
tighten
40mm (19/16") Min gap
A+B
A+B
Use Plasterboard /
Sheetrock fixings
A+B
Ø10mm
(25/64")
75mm (3")
Ø5.5mm
(7/32")
A+B
Use Plasterboard /
Sheetrock fixings
Ø3.5mm
(9/64")
SRQPONMLKJIHBA
N
O
M
Q
I
PK
O
J
O
R
P
H S
P
P
Use Plasterboard /
Sheetrock fixings
Self drilling
Self drilling
Self drilling
A+B
A+B
Self drilling
40mm (19/16")
O
O
N
L

10
Hanging The TV
I II
III IV
Present the yellow Hangers
(on the back of the TV) to the
guide recess on the Wall
Brackets. Slide down and across
into place. Ensure both yellow
Hangers are fully engaged.
If cables from the TV prevent
the TV resting against the wall
then an alternative hanger
configuration will be required
(See Section 11).
TV must be parallel to wall. Use
spacers / stand-offs as shown.
Guide
Recess
If required you can adjust
the level of your TV by moving
your TV from side to side.
Removing the TV
This is a two person job. To remove the TV reverse the movements as shown above.

11
Alternative Hanger Configurations
Alternative Wall spacings of 12mm, 20mm & 40mm can
be achieved using the spacer / screw combinations
listed in this section.
20mm Wall Space
(as shown in section 4)
12mm Wall Space 40mm Wall Space
*F1, 2, 3
G1, 4, 7, 10
Top FixingsTop Fixings Top Fixings
C*F1, 2, 3
G2, 5, 8, 11
C*F1, 2, 3
G3, 6, 9, 12
C
E1
Wall Space
E1
Bottom Fixings
E1
E1
*
When is it necessary to use red spacers? E2- x4
TV TV
E1E2
It is recommended that when fitting Hangers ( ) and
Stand-offs ( ) to your TV you have at least 5-10mm of
screw engagement. In certain circumstances you may
need to use red spacers ( ) as either a replacement, or
together with spacers ( ) to achieve this. Whenever
you use red spacers (E2) you must use all 4 provided.
C
D
E2
E1
Problem
Not enough
screw engagement
Solution
Red spacer (E2) has
replaced spacer (E1)
TV must be parallel to wall. Use spacers / stand-offs as shown.
If using screw (G1),(G2) or (G3) use Adapter (F1)
If using screw (G4),(G5) or (G6) use Adapter (F2)
If using screw (G7),(G8) or (G9) use Adapter (F3)
If using screw (G10),(G11) or (G12) No Adapter required
Bottom FixingsBottom Fixings
G1, 4, 7, 10
*F1, 2, 3
G2, 5, 8, 11
*F1, 2, 3
D
G3, 6, 9, 12
*F1, 2, 3
D
E1
D
E1
E1
E1