Avidsen ORANE510 User manual

2. EQUIPMENT REQUIRED (NOT SUPPLIED)
The tools and screws required for the installation must be in good condition and compliant with applicable safety standards.
¡[
[ [
¡[
¡
1 drill
1 at head
screwdriver 1 pencil
1 spirit level
1 x 13mm spanner
1 measuring tape
1 x 19mm box spanner
and 1 x 13mm box spanner
1 Phillips screwdriver
Flashing light Motor attachment of the
motors
onto the pillars
3m cable
2 x 0.5mm2
8m cable
2 x 1.5mm2
Thank you for purchasing an AVIDSEN automatic gate opener.
This document is a quick start guide detailing the main installation steps as well as the equipment required. To perform the installation, please
download the installation manual at the following address: www.avidsen.com
Warning: The safety instructions and installation instructions can be found in the installation manual. Follow all these instructions, as an
incorrect installation can cause serious injuries.
1. DESCRIPTION
V3
Ref. 114201
EN
ORANE510
MOTOR DRIVE
WITH PIVOTING ARMS
For 2-panel swing gates
attachment of the
brackets on the gate:
Choose a screw/nut
system appropriate
for the thickness of
the gate. There are 4
attachment points
Photocells
10m cable
4 x 6/10
1Main motor with electronic card
2Secondary motor
3Remote control
4Flashing light and screws
5Rear arm
6Front arm
7Post mounting bracket
8Gate mounting bracket
9M12 – L40 screw
10 M8 – L25 screw
11 M10 – L90 screw
12 M8 CHC – L30 screw
13 M8 washer
14 M8 spring washer
15 M12 locknut
16 M10 nut
17 M10 spring washer
18 M10 washer
19 M8 washer oversized
20 M10 - L120 fastening pin
21 Photocells and screws
22 Allen key
23 M12 washer
1x 1 3x 2 4x 1 4x 2 4x 2 5x 2 6x 2 7x 2 8x 2
9x 4 10 x 2 11 x 4 12 x 4 13 x 4 14 x 6 15 x 4 16 x 4 17 x 4 20 x 6
2x 1
18 x 4
19 x 2
23 x 4 22 x 1 21 x 1 21 x 6 21 x 6 21 x 4

3. INSTALLATION
Safety guidelines: please refer to the installation manual for all safety instructions.
To perform the installation, please download the installation manual at the following address: www.avidsen.com
Overview:
The cables used must be appropriate for outdoor use (such as H07RN-F for example). The cable run between the two posts must comply with applicable
standards (NFC 15-100). The power cable of the opposite geared motor must run 80cm deep with red warning mesh.
Motors
Inner side of the property
Flashing light
1
2
3
4
5
List of cables:
Connection Cable Max length
1 230VAC power line Cable 3 x 2.5mm2 (more than 30m long)
Cable 3 x 1.5mm2 (less than 30m long) Unlimited
2 Flashing light Cable 2 x 0.5mm2 15m
3 Secondary motor 2 x 1.5mm² cable 10m
4 Reception photocell (RX) 4 x 6/10 cable 10m
5 Transmission photocell (TX) 4 x 6/10 cable 10m
The installation is a 4-step process:
1. Installation of the motors onto the pillars and gate, and of the flashing light (the main motor is installed on the pillar where the power comes from).
2. Electrical connection:
- of the secondary motor to the electronic card (in the main motor)
- of the flashing light to the electronic card (in the main motor)
- of the photocells to the electronic card (in the main motor)
- connection of the transformer to the mains. This connection must be performed by qualified personnel (electrician, etc.)
3. Adjustments and operation:
Note: Only switch on the system once all connections have been made.
- Read the installation manual chapter on simple adjustments.
- Launch the movement self-learning programme (press "+" for 3 seconds)
- Programme the remote controls:
- press "-" for three seconds, press "OK", press the remote control button to be memorised, repeat the operation for each remote control
- Choice of operating mode:
By default, automatic closing is deactivated. To activate it:
- Press PROG for three seconds, press "OK", press "+", press "OK"
4. Operational testing: To familiarise yourself with the automatism and ensure it operates properly, read the chapter on usage and conduct operational tests (open/
close, initiate obstacle detection, cut the photocell beam). Upon completion of these tests, you may have to modify certain settings (e.g. motor power).
4. DECLARATION OF CONFORMITY
Avidsen declares that the equipment complies with the essential applicable requirements of RED Directive 2014/53/EU.
Directive 2014/35/EU: (protection of users’ health and safety)
Directive 2014/30/EU: (protection requirements relating to electromagnetic compatibility).
Directive 2014/53/EU: (efficient use of the radio spectrum, in order to avoid harmful interference).
The full declaration of compliance is available on the website www.avidsen.com
Tours, 02/11/2020
Alexandre Chaverot, CEO
Pour en savoir plus :
www.quefairedemesdechets.fr
Avidsen
19 avenue Marcel Dassault - ZAC des Deux Lions - 37200 Tours - France