Avidsen STYRKA310 User manual

1 24V motorised cylinders
2 Control unit
3 Pillar mounting bracket
4 Gate mounting bracket
5 Clevis pins
6 Spacer
7 Elastic pin
8 Remote control
9 Flashing light
9x 1 8x 2
EQUIPMENT REQUIRED (NOT SUPPLIED)
The tools and screws required for the installation must be in good condition and compliant with applicable safety standards.
  ¡
¡
¡
[ [
¡
¡ ¡[
¡
[ [
¡[
¡
drilling the
post
flashing light actuators attachment to the post:
- electronic panel
- flashing light
attachment of the
brackets
onto the posts:
3m cable
2 x 0.5mm2 10m cable
2 x 1.5mm2
drilling into
the gate
1x 1 3x 4 4x 2
2x 1
5x 1 5x 1 6x 4 7x 4
Thank you for purchasing an AVIDSEN automatic gate opener.
This document is a quick start guide detailing the main installation steps as well as the equipment required. To install, please download the installation
manual from the following webpage: www.avidsen.com/produits/recherche.php
Warning: The safety instructions and installation instructions can be found in the installation manual. Follow all these instructions, as an
incorrect installation can cause serious injuries.
CONTENTS OF THE KIT
V2
STYRKA310
TELESCOPIC
MOTOR DRIVE KIT
Piston-style – For 2-panel gates
Ref. 114170
EN
attachment of the
brackets
on the gate:
Choose a screw/nut
system
appropriate for the
thickness of the gate.
There are 4 attachment
points

INSTALLATION
Safety guidelines: please refer to the installation manual for all safety instructions.
To install, please download the installation manual from the following webpage: www.avidsen.com/ produits/recherche.php
Overview:
The cables used must be appropriate for outdoor use (such as H07RN-F for example).
The cable run between the two posts must comply with applicable standards (NFC 15-100).
The geared motor power cable must run 80cm deep with red warning mesh.
actuators
Inner side of the property
Flashing light
Switchgear
control unit
1
3
4
2
List of cables:
Connection Cable Max length
1 230VAC power line Cable 3 x 2.5mm2 (more than 30m long)
Cable 3 x 1.5mm2 (less than 30m long) Unlimited
2 Flashing light Cable 2 x 0.5mm2 15m
3 Left motor Cable 2 x 1.5mm² 10m
4 Right motor Cable 2 x 1.5mm² 10m
The installation is a 4-step process:
1. Installation of the cylinders onto the pillars and gate, and of the electronic panel and flashing light.
2. Electrical connection of the motors, flashing light and electronic panel to the mains. This connection must be performed by qualified personnel
(electrician, etc.).
3. Adjustments and operation:
Warning: Only switch on the electronic panel once all connections have been made.
- Read the installation manual chapter on simple adjustments.
- Launch the movement self-learning programme (press "+" for 3 seconds)
- Programme the remote controls:
- press "-" for 3 seconds
- press "SET"
- press the remote control button to be memorised
- Repeat the operation for each remote control
- Choice of operating mode:
By default, automatic closing is deactivated. To activate it, you must install a pair of photocells (optional)
4. Operational testing: To familiarise yourself with the automatism and ensure its proper operation, read the chapter on usage and conduct operational tests
(opening/closing, initiate obstacle detection, cut the photocell beam (optional). Upon completion of these tests, you may have to modify certain settings (e.g.
motor power).
DECLARATION OF CONFORMITY
avidsen declares that the equipment complies with the essential applicable requirements of RED Directive 2014/53/EU.
Directive 2014/35/EU: (protection of users’ health and safety)
Directive 2014/30/EU: (protection requirements relating to electromagnetic compatibility).
Directive 2014/53/EU: (efficient use of the radio spectrum, in order to avoid harmful interference).
The full declaration of compliance is available on the website www.avidsen.com
Tours, 16/11/2021
Alexandre Chaverot, CEO
Pour en savoir plus :
www.quefairedemesdechets.fr
Avidsen
19 avenue Marcel Dassault - ZAC des Deux Lions - 37200 Tours - France