AXIOMTEK AIE800-904-FL-DC Series User manual

AIE800-904-FL-DC
Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without
the prior written permission of Axiomtek Co., Ltd.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
NVIDIA® , the NVIDIA logo, Jetson™, Jetson Xavier™, and Jetson AGX Xavier™are
trademarks of the NVIDIA Corporation.
Other brand names and trademarks are the properties and registered brands of their respective
owners.
©Copyright 2022 Axiomtek Co., Ltd.
All Rights Reserved
October 2022, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The AIE800-904-FL-DC does not come with an operating system which must be loaded
first before installation of any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a wrist grounding strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the AIE800-904-FL-DC prior to making any installation.
Be sure both the system and all external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the AIE800-904-FL-DC is properly grounded.
4. Make sure the voltage of the power source is correct before connecting it to any power
outlet.
5. Turn off system power before cleaning. Clean the system using a cloth only. Do not spray
any liquid cleaner directly onto the screen.
6. Do not leave equipment in an uncontrolled environment where the storage temperature is
below -40℃or above 80℃as it may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
⚫Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help discharge any static electricity on human
body.
⚫When handling boards and components, wear a wrist grounding strap available from
most electronic component stores.

iv
Classifications
1. Degree of production against electric shock: not classified
2. Degree of protection against ingress of water: IP67
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air,
oxygen or nitrous oxide.
4. Mode of operation: Continuous
Note: All I/O connectors should be connected with corresponding cables when the system
Is operating with IP67 rated definition. If some of the I/O ports are not to be used or
Connected during operation, users must use I/O covers to plug the ports in order to
meet the IP67 standard.

v
General Cleaning Tips
Please keep the following precautions in mind while understanding the details fully before and
during any cleaning of the computer and any components within.
A piece of dry cloth is ideal to clean the device.
1. Be cautious of any tiny removable components when using a vacuum cleaner to absorb
dirt on the floor.
2. Turn the system off before cleaning up the computer or any components within.
3. Avoid dropping any components inside the computer or getting the circuit board damp or
wet.
4. For cleaning, be cautious of all kinds of cleaning solvents or chemicals which may cause
allergy to certain individuals.
5. Keep foods, drinks or cigarettes away from the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
computer and peripherals, users can also use household items accordingly for cleaning. Listed
below are items available for cleaning computers or computer peripherals.
Pay special attention to components requiring designated products for cleaning as
mentioned below.
⚫Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, it is recommended to use
a piece of cloth.
⚫Water or rubbing alcohol: A piece of cloth may be somewhat moistened with water or
rubbing alcohol before being rubbed on the computer. Unknown solvents may be harmful
to plastic parts.
⚫Vacuuming dust, dirt, hair, cigarette and other particles outside of a computer can be one
of the best methods of cleaning a computer. Over time these items may restrict the airflow
in a computer and cause circuitry to corrode.
⚫Cotton swabs: Cotton swabs moistened with rubbing alcohol or water are applicable to
reach areas in a keyboard, mouse and other areas.
⚫Foam swabs: If possible, it is better to use lint free swabs such as foam swabs.
Note: It is strongly recommended that the customer should shut down the system before
starting to clean any single components.
Please follow the steps below:
1.Close all application programs;
2.Close operating software;
3.Turn off power switch;
4.Remove all devices;
5.Pull out the power cable.

vi
Scrap Computer Recycling
Please inform the nearest Axiomtek distributor as soon as possible for suitable solutions in case
computers require maintenance or repair; or for recycling in case computers are out of order or
no longer in use.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
NVIDIA® and Jetsonare registered trademarks of NVIDIA Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
Windows 10, Linux and other brand names and trademarks are the properties and
registered brands of their respective owners.

vii
Table of Contents
Disclaimers............................................................................................................. ii
Safety Precautions................................................................................................ iii
Classifications.......................................................................................................iv
General Cleaning Tips ...........................................................................................v
Scrap Computer Recycling................................................................................... vi
SECTION 1 INTRODUCTION.........................................................................1
1.1 General Descriptions.........................................................................1
1.2System Specifications.......................................................................2
1.2.1 Product Specification......................................................................................2
1.2.2 I/O System ........................................................................................................3
1.2.3 System Specification.......................................................................................3
1.3 Dimensions ........................................................................................4
1.3.1 System Dimensions.........................................................................................4
1.3.2 Wall-mount Bracket Dimensions ...................................................................5
1.3.3 VESA-mount Bracket Dimensions.................................................................6
1.4 I/O Outlets...........................................................................................7
1.5Packing List........................................................................................ 8
1.6Model List...........................................................................................8
SECTION 2 HARDWARE INSTALLATION ...................................................9
2.1M.2 SSD Installation......................................................................... 10
2.2 Installation of Wireless Network Mini PCIe Module.......................12
SECTION 3 JUMPER & CONNECTOR SETTINGS.....................................15
3.1 Jumper & Connector Location........................................................15
3.2 Jumper Setting Summary................................................................ 17
3.3 Connectors.......................................................................................18
3.3.1 PoE Power Output Connector (M12 X-Code 8 pos Female)......................18
3.3.2Dual USB 2.0 Connector (M12 A-Code 8 pos Male)....................................19
3.3.3 DC Power Jack Connector (M12 A-Code 5 pos Male)................................19
3.3.4 HDMI Connector (C3 Type 19 pos Female) .................................................19
3.3.5 Micro USB 2.0 Connector (CN1)...................................................................20
3.3.6 Debug Port Connector (CN2)........................................................................20
3.3.7 CMOS Battery Interface (BAT1)....................................................................20
3.3.8 M.2 2242 Key B NVMe SSD (SCN1).............................................................21
3.3.9 SIM Card Slot (SCN2) ...................................................................................22
3.3.10 PCI-Express Mini Card Connector (SCN3)..................................................23
3.4 Waterproof Cables........................................................................... 24
3.4.1 Power Cable (Optional) .................................................................................24
3.4.2 USB Cable (Optional) ....................................................................................25
3.4.3 LAN/PoE Cable (Optional).............................................................................25
SECTION 4 JETPACK FLASH METHOD....................................................27
4.1 Jetpack Flash Method......................................................................27
4.2 Image Information Inquiry Command.............................................31
4.3 JTOP —Third-party Jetson Platform Monitor Tool ....................... 32

viii
This page is intentionally left blank.

AIE800-904-FL-DC Series User’s Manual
Introduction 1
SECTION 1
INTRODUCTION
This chapter contains general information and detailed specifications of the AIE800-
904-FL-DC. Section 1 consist of the following sub-sections:
⚫General Description
⚫System Specifications
⚫Dimensions
⚫I/O Outlets
⚫Packing List
⚫Model List
1.1 General Descriptions
The AIE800-904-FL-DC comes with the NVIDIA®Jetson Xavier™NX System-on-module (SoM)
and supports Linux Ubuntu 18.04. In order to achieve optimal durability and heat dissipation,
this ruggedized box PC adopts a fanless and streamlined enclosure made from IP67-rated
aluminum die-casting and heavy-duty steel.
The AIE800-904-FL-DC is designed to operate under a wide temperature range from
-30°C to 50°C. It also supports wide-range DC power input from 9 to 36 VDC and features
M12 lockable connectors, making the box PC particularly suited for operation in mission-critical
applications and harsh outdoor environments.
⚫Features
1. IP67-rated design, specifically for outdoor environments
2. NVIDIA® Jetson Xavier™NX with 384-core NVIDIA Volta™GPU with 48 Tensor Cores
3. High AI computing performance for GPU accelerated processing
4. -30°C to +50°C wide operating temperature range
5. 9 ~ 36 VDC wide range power input

AIE800-904-FL-DC Series User’s Manual
2 Introduction
6. 1 IEEE 802.3at GbE PoE (15W)
7. Flexible I/O for customized and mission-critical projects
⚫Reliable and Stable Design
Powered by the NVIDIA® Jetson Xavier™NX SoM, the AIE800-904-FL-DC is
equipped with M12 lockable connectors while supporting a wall mount / VESA mount
kit for outdoor applications.
⚫JetPack Supported
The AIE800-904-FL-DC supports JetPack 4.6.2 or later. NVIDIA JetPack SDK is the most
comprehensive solution for building AI applications.
JetPack supports Jetson AGX Xavier™, Jetson Xavier™NX, Jetson™TX2 NX, Jetson™
Nano and Jetson TX2 series. It bundles all the Jetson platform software, including
TensorRT, cuDNN, CUDA Toolkit, VisionWorks, GStreamer, and OpenCV, all built on top
of L4T with LTS Linux kernel.
⚫O.S. Supported
The AIE800-904-FL-DC supports Linux Ubuntu 18.04 or later.
⚫Various Storage devices supported
For optimized storage capacity, the AIE800-904-FL-DC supports one M.2 Key B 2242 with
PCI-Express 2.0 x2 Interface (supports NVMe SSD only), and an onboard 16GB eMMC
(via Jetson Xavier™NX).
1.2System Specifications
1.2.1 Product Specification
⚫CPU Board
◼NVIDIA® Jetson Xavier™NX
⚫CPU
◼6-core NVIDIA Carmel ARM® v8.2 64-bit CPU 6 MB L2 + 4 MB L3
⚫GPU
◼384-core NVIDIA Volta™GPU with 48 Tensor Cores
⚫Storage
◼16GB eMMC onboard
◼One M.2 Key B 2242 with PCI-Express 2.0 x2 NVMe SSD slot
⚫System Memory
◼One 8GB or 16GB 128-bit LPDDR4x onboard
⚫WLAN & WWAN
◼Supports Wi-Fi/Bluetooth/LTE/GPS through an optional Mini PCI-Express module

AIE800-904-FL-DC Series User’s Manual
Introduction 3
1.2.2 I/O System
⚫One C3 type HDMI for display ( HDMI Full HD Resolution: up to 1920 x 1080 )
⚫One M12 X-Code IEEE 802.3at Gigabit PoE (15W)
⚫One M12 A-Code connector for Dual USB 2.0
⚫One full-size PCI Express Mini Card slot ( USB + PCI Express signal )
⚫One SIM slot
⚫Four N Jack type antenna openings with waterproof design
※The AIE800-904-FL-DC supports either LTE or Wi-Fi only. To facilitate maintenance, the
AIE800-904-FL-DC supports 4 antenna openings and comes with two pre-installed LTE
and two pre-installed Wi-Fi RF cables before shipment.
⚫One M12 A-Code 5 pos DC in power input
1.2.3 System Specification
⚫Watchdog Timer
◼Supports the watchdog timer embedded in NVIDIA®Jetson Xavier™NX
⚫Power Supply
◼Input: 9 ~ 36 VDC
⚫Operation Temperature
◼-30℃~ 50℃(-22 ºF ~ 122ºF)
⚫Storage Temperature
◼-40℃~ 80℃(-40 ºF ~ 176ºF)
⚫Humidity
◼10% ~ 95% (non-condensation)
⚫Vibration Endurance
◼3Grm with eMMC (5-500Hz, X, Y, Z directions)
⚫Weight
◼4.13 kg (9.11 lb) without package
◼5.5 kg (12.13 lb) with package
⚫Dimensions
◼366.8 mm (14.44") (W) x 235 mm (9.25") (D) x 83.8 mm (3.3”) (H)
Note: All specifications and images are subject to change without notice.

AIE800-904-FL-DC Series User’s Manual
4 Introduction
1.3 Dimensions
The following diagrams show the dimensions and outlines of the AIE800-904-FL-DC.
1.3.1 System Dimensions

AIE800-904-FL-DC Series User’s Manual
Introduction 5
1.3.2 Wall-mount Bracket Dimensions

AIE800-904-FL-DC Series User’s Manual
6 Introduction
1.3.3 VESA-mount Bracket Dimensions

AIE800-904-FL-DC Series User’s Manual
Introduction 7
1.4I/O Outlets
The following figures show I/O outlets on the front of the AIE800-904-FL-DC.
Top View
Bottom View

AIE800-904-FL-DC Series User’s Manual
8 Introduction
1.5Packing List
The package bundled with your AIE800-904-FL-DC should contain the following items:
⚫AIE800-904-FL-DC system unit x 1
⚫Screws pack x 1
⚫Thermal pad kit x 1
⚫(Optional) Power cord x 1
⚫(Optional) USB cable x 1
⚫(Optional) LAN cable x 1
⚫(Optional) M.2 NVMe SSD x 1
⚫(Optional) Wi-Fi / Bluetooth / LTE / GPS module kit
※Regarding the latest product manual, please download them from Axiomtek official website.
1.6Model List
AIE800-904-FL-DC
Rugged IP67-rated Fanless Edge AI System with NVIDIA®
Jetson Xavier™NX, 1 HDMI, 1 GbE PoE, 2 USB and 9 to 36
VDC Power Input
Please contact Axiomtek’s distributors immediately in case any abovementioned items are
missing.

AIE800-904-FL-DC Series User’s Manual
Hardware Installation 9
SECTION 2
HARDWARE INSTALLATION
The AIE800-904-FL-DC is convenient for various hardware configurations, such as SSD (Solid
State Drive) and PCI Express Mini card modules. Section 2 contains guidelines for hardware
installation.
※CAUTION:
Run Waterproof capability may be affected if the system is improperly
disassembled. Under such circumstances Axiomtek shall not be held
liable for any quality deterioration.
Please refer to the tightening torque information below for all system screws:
HEX Socket Set Screw: 7.5 kgf
HEX KEY specifications are shown below:
N Jack Connector:
⚫VDC IN, USB, PoE, Wi-Fi & LTE: 10 kgf
⚫HDMI: 19 kgf

AIE800-904-FL-DC Series User’s Manual
10 Hardware Installation
2.1M.2 SSD Installation
Step 1 Turn off the system and unplug the power cord.
Step 2 Turn the system upside down to locate and loosen the six screws at the bottom,
as marked by the red circles in the figure below. Then remove the bottom cover.
Step 3 After removing the bottom cover, locate the M.2 2242 Key B slot on the board,
then take two thermal pads out of the package box, and apply one thermal pad
on the M.2 2242 Key B slot.

AIE800-904-FL-DC Series User’s Manual
Hardware Installation 11
Step 4 While holding the M.2 2242 Key B SSD at a 30-degree angle up from the
horizontal, slowly insert the golden finger into the M.2 2242 Key B slot until it is
fully inserted in place. And secure the M.2 2242 Key B SSD to the carrier by
tightening up one M3*3L screw to the marked position. Then apply another
thermal pad on the M.2 2242 Key B SSD.

AIE800-904-FL-DC Series User’s Manual
12 Hardware Installation
2.2Installation of Wireless Network Mini PCIe Module
Step 1 Turn off the system and unplug the power cord.
Step 2 Turn the system upside down to locate and loosen the six screws at the bottom,
as marked by the red circles in the figure below. Then remove the bottom cover.
Step 3 After removing the bottom cover, locate the PCI Express mini card slot
on the board.
Step 4 While holding the PCI Express mini card at a 45-degree angle up from
the horizontal, slowly insert the golden finger into the PCI Express slot
until it is fully inserted in place.