AXIOMTEK PICO841 User manual

4 9418H841010E
©Copyright 2015 Axiomtek Co., Ltd.
Version A2 October 2015
Printed in Taiwan
Quick Start
The basic procedures required to power on PICO841/843:
Note: Please refer to AX93283 and AX93267 quick installation guide for I/O
board related information.
(1). Require at least 60W DC power adapter. Before connecting to
PICO841/843, ensure that all necessary peripheral devices are
plugged properly.
(2). Ensure all of the jumpers are in their default settings, especially JP4
(1-2 close).
(3). To ensure normal functioning, DDR3L memory module must be
installed into SSODIMM1 until fully seated.
Note: It must be DDR3L memory module.
(4). Install heatspreader plate, AX93283 and AX93267 I/O boards as
indicated in the image below.
(5). Firmly insert DC power adapter to CN1 on AX93267.
(6). Press system power switch (CN5) on AX93283 to start PICO841/843.
Note: Before installing Windows®7, please read Appendix B in the user’s
manual.
PICO841/843
AX93283
AX93267
PICO841/843 Quick Installation Guide
9418H841010E 1
©Copyright 2015 Axiomtek Co., Ltd.
Version A2 October 2015
Printed in Taiwan
Checklist
Pico-ITX board x1 SATA cable x1
Product information CD x1 SATA power cable x1
Quick installation guide x1 Heatspreader x1
AX93283 I/O board x1 Heatsink x1
AX93267 I/O board x1
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Board Layout
Top View
PICO841/PICO843 Pico-ITX Board

2 9418H841010E
©Copyright 2015 Axiomtek Co., Ltd.
Version A2 October 2015
Printed in Taiwan
Bottom View
Side View
Note: Please refer to the PICO841/843 product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.
9418H841010E 3
©Copyright 2015 Axiomtek Co., Ltd.
Version A2 October 2015
Printed in Taiwan
Jumper Settings
Before applying power to the PICO841/843, please make sure all of the
jumpers are in factory default position.
Jumper Description Setting
JP1 LVDS +12V Voltage Selection
Default: None None
JP2 LVDS +3.3V/+5V Voltage Selection
Default: +3.3V 1-2 Close
JP4 Auto Power On
Default: Disable 1-2 Close
JP5 LVDS Brightness Control Mode Setting
Default: PWM Mode 1-2 Close
JP6 Restore BIOS Optimal Defaults
Default: Normal Operation 1-2 Close
Connectors
Connector Description
CN1 20-pin Board to Board Connector
CN2 40-pin Board to Board Connector
CN3 Fan Power Connector
CN4 SMBus Connector
CN6 Power LED Header
CN7 External Speaker and Internal Buzzer Header
CN8 LVDS Connector
CN9 SATA Power Connector
CN10 Inverter Connector
CN11 DC Power Connector
CN12 VGA Connector
LAN1 Ethernet Port
SATA1 SATA Connector
BAT1 CMOS Battery Connector
SCN1 Full-size PCI-Express Mini Card and mSATA Connector
SCN2 SIM Card Slot
SCN3 Half-size PCI-Express Mini Card Connector
SSODIMM1 DDR3L SO-DIMM Socket