AXIOMTEK SHB130 Series User manual

SHB130 Series
Intel®Socket 1150 CoreTM i7 / CoreTM
i5 / CoreTM i3 Processor
PICMG®v1.3 Full-size CPU Card
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
August 2013, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®CoreTM i7 / CoreTM i5 / CoreTM i3 are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Utilities Supported ..............................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Dimensions and Fixing Holes.................................................5
2.2 Board Layout.......................................................................................6
2.3 Jumper Settings..................................................................................7
2.3.1 Audio Amplifier Selection (JP1)................................................................... 8
2.3.2 Restore BIOS Optimal Defaults (JP2)......................................................... 8
2.3.3 Auto Power On (JP4) .................................................................................. 8
2.4 Connectors ..........................................................................................9
2.4.1 External Temperature Sensor Connector (CN1) (Optional) ...................... 10
2.4.2 SMBus Connector (CN2) .......................................................................... 10
2.4.3 Digital I/O Connector (CN3) ...................................................................... 10
2.4.4 Internal USB 3.0 Connector (CN4).............................................................11
2.4.5 LAN External LED Connectors (CN5 and CN6).........................................11
2.4.6 DVI-D Connector (CN7) .............................................................................11
2.4.7 Internal USB 2.0 Connectors (CN8, CN11 and CN12) ............................. 12
2.4.8 VGA Connector (CN9)............................................................................... 12
2.4.9 DisplayPort Connector (CN10) (Optional)................................................. 13
2.4.10 Front Panel Connector (CN13) ................................................................. 14
2.4.11 External USB 3.0 Connectors (CN14 and CN17) ..................................... 15
2.4.12 Internal Keyboard and Mouse Connectors (CN16 and CN15) ................. 15
2.4.13 FAN Connectors (FAN1, FAN2 and FAN3) ............................................... 16
2.4.14 Ethernet Ports (LAN1 and LAN2).............................................................. 16
2.4.15 Parallel Port (PRINT1) .............................................................................. 17
2.4.16 Serial ATA Connectors (SATA1~SATA6) ................................................... 17
2.4.17COM Connectors (COM1~COM5)............................................................ 18
2.4.18 Audio Connector (AUDIO1)....................................................................... 19
2.4.19 Power Connector (ATX2) .......................................................................... 19
Chapter 3 Hardware Installation ........................... 21
3.1 Installing the Processor....................................................................21

v
3.2 Installing the Memory .......................................................................24
Chapter 4 Hardware Description ........................... 25
4.1 Microprocessors ...............................................................................25
4.2 BIOS ...................................................................................................25
4.3 System Memory.................................................................................25
4.4 I/O Port Address Map........................................................................26
4.5 Interrupt Controller (IRQ) Map .........................................................28
4.6 Memory Map ......................................................................................31
Chapter 5 AMI BIOS Setup Utility .......................... 33
5.1 Starting...............................................................................................33
5.2 Navigation Keys ................................................................................33
5.3 Main Menu..........................................................................................34
5.4 Advanced Menu.................................................................................35
5.5 Chipset Menu.....................................................................................46
5.6 Boot Menu..........................................................................................49
5.7 Security Menu....................................................................................50
5.8 Save & Exit Menu ..............................................................................51
Appendix A Watchdog Timer................................... 53
About Watchdog Timer................................................................................53
How to Use Watchdog Timer.......................................................................53
Appendix B Digital I/O ............................................. 55
About Digital I/O...........................................................................................55
How to Use Digital I/O..................................................................................55
Appendix C PCI IRQ Routing ................................... 57
PICMG®PCI IRQ Routing.............................................................................57
Appendix D Configuring SATA for RAID .................. 59
Configuring SATA Hard Drive(s) for RAID (Controller: Intel®Q87)..........59
Appendix E iAMT Settings ...................................... 67
Entering MEBx .............................................................................................67
Set and Change Password..........................................................................67
iAMT Settings...............................................................................................69

vi
iAMT Web Console ......................................................................................72
Appendix F PICMG®v1.3 Interface Definition.......... 75

SHB130 LGA1150 Full-size CPU Card
Introduction 1
Chapter 1
Introduction
The SHB130 PICMG®v1.3 full-size Single Board Computer supports LGA1150 socket for
Intel®CoreTM i7 desktop processor, i5 desktop processor, i3 desktop processor with 22nm
technology and transfer rate 1333/1600MHz. The board integrates Intel®Q87 chipset that
delivers outstanding system performance through high-bandwidth interfaces, multiple I/O
functions for interactive applications and various embedded computing solutions. There are
two 240-pin DDR3 DIMM sockets for dual channel DDR3/L 1333/1600 with maximum memory
capacity up to 16GB. The board also features dual Gigabit Ethernet and six SATA 6Gb/s with
SATA RAID 0/1/5/10 by PCH. Ten USB 2.0 and four USB 3.0 high speed compliant ports and
built-in Intel®HD Audio Digital Header can achieve the best stability and reliability for industrial
applications.
1.1 Features
LGA1150 socket 4th Generation Intel®CoreTM processors up to 65W
Intel®Q87 PCH
2 DDR3/L unbuffered DIMM max. up to 16GB memory capacity
Intel®iAMT 9.0 and TPM supported (optional)
PCIe Gen. 3 at 8GT/s supported
DVI-D and VGA or DisplayPort dual display
USB 3.0 supported

SHB130 LGA1150 Full-size CPU Card
2 Introduction
1.2 Specifications
CPU
Intel®CoreTM i7 desktop processor.
Intel® CoreTM i5 desktop processor.
Intel® CoreTM i3 desktop processor.
CPU TDP up to 65W
System Chipset
Intel®Q87.
CPU Socket
LGA1150 Socket.
DRAM Transfer Rate
1333/1600MHz.
BIOS
AMI BIOS via SPI interface with socket.
System Memory
Two 240-pin DDR3/L 1333/1600MHz DIMM sockets.
Maximum up to 16GB DDR3/L memory.
L1, L2, L3 Cache: Integrated in CPU
Onboard Multi I/O
Parallel port: One 26-pin 2.54 pitch box-header, SPP/EPP/ECP supported.
Serial ports: Four RS-232 ports with 10-pin, 2.54 pitch box-header (COM2/3/4/5) and
one RS-232/422/485 port with 10-pin, 2.54 pitch box-header (COM1).
USB Interface
Four USB ports compliant with USB Spec. Rev. 3.0 (2 ports on rear I/O, 2 ports
onboard).
Ten USB ports compliant with USB Spec. Rev. 2.0 (6 ports onboard, 4 ports on SHB
connector-C golden fingers).
Onboard Graphic
Intel®Arrandale integrated a Graphic processing unit processor which goes with Q87
chipset supporting VGA, DisplayPort (co-layout with VGA) and DVI-D.
Memory size: Intel®DVMT 5.0 supported; preallocated memory for frame buffer
option as OS option:
Windows®XP:
For total system memory < 1GB,
Graphics sharing memory = 128MB maximum;
For 1GB to 1.5GB total system memory,
Graphics sharing memory = 512MB maximum;
For 1.5GB to 2GB total system memory,
Graphics sharing memory = 768MB maximum;
For 2GB and above total system memory,
Graphics sharing memory = 1GB maximum.
Windows®Vista:
Graphics sharing memory maximum up to 0.5* (OS Ram size –512).

SHB130 LGA1150 Full-size CPU Card
Introduction 3
Resolution: Analog output - the analog port utilizes an integrated 400MHz 24-bit
RAMDAC that can directly drive a standard progressive scan analog monitor up to a
resolution of 2048x1536 pixels with 32-bit color at 75Hz.
Analog output interface: CRT from DAC output via 15-pin D-Sub connector on the
edge; CRT always ON supported.
Ethernet
LAN1/LAN2: Intel®i217LM with iAMT 9.0 / Intel®i210AT Ethernet controller; support
1000/100/10Mb/s.
Note: The Intel®i217LM does not support S1 LAN Wake.
Serial ATA
Six SATA 3.0 ports (6Gb/s performance) with SATA RAID 0/1/5/10 by Q87.
Note: Due to Gen. 2 SSD with JMicron controller has compatibility issue with Intel Q87 PCH,
we strongly recommend to use Gen. 3 SSD on SHB130.
Audio
10-pin 2.0 box-header (Intel®HD Audio Digital Header).
Hardware Monitoring
Monitoring temperatures, voltages and cooling fan status.
Watchdog Timer
Reset supported; up to 256 levels.
Dimensions
338mm x 126mm.
Expansion Interface
One PCI-Express x16 (Gen.3).
One PCI-Express x4 (or four PCI-Express x1 ) (Gen.2).
Four PCI.
Note: All specifications and images are subject to change without notice.
1.3 Utilities Supported
Intel®Q87 utility and drivers
VGA drivers
Audio utility and drivers
Ethernet utility and drivers
RAID utility
iAMT utility and drivers
TPM utility

SHB130 LGA1150 Full-size CPU Card
4 Introduction
This page is intentionally left blank.

SHB130 LGA1150 Full-size CPU Card
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Dimensions and Fixing Holes

SHB130 LGA1150 Full-size CPU Card
6 Board and Pin Assignments
2.2 Board Layout

SHB130 LGA1150 Full-size CPU Card
Board and Pin Assignments 7
2.3 Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.
Before applying power to SHB130 Series, please make sure all of the jumpers are in factory
default position. Below you can find a summary table and onboard default settings.
Jumper
Description
Setting
JP1
Audio Amplifier Selection
Default: Disable
1-3, 2-4 Close
JP2
Restore BIOS Optimal Defaults
Default: Normal Operation
1-2 Close
JP4
Auto Power On
Default: Disable
1-2 Close

SHB130 LGA1150 Full-size CPU Card
8 Board and Pin Assignments
2.3.1 Audio Amplifier Selection (JP1)
This jumper is for enabling or disabling audio amplifier.
2.3.2 Restore BIOS Optimal Defaults (JP2)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this
procedure can restore BIOS optimal defaults.
2.3.3 Auto Power On (JP4)
If JP4 is enabled for AC power input, the system will be automatically power on without
pressing soft power button. If JP4 is disabled for AC power input, it is necessary to
manually press soft power button to power on the system.
Function
Setting
Disable (Default)
1-3, 2-4 close
Enable
3-5, 4-6 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Function
Setting
Disable auto power on (Default)
1-2 close
Enable auto power on
2-3 close

SHB130 LGA1150 Full-size CPU Card
Board and Pin Assignments 9
2.4 Connectors
Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table which shows all connectors on the hardware.
Connector
Description
CN1
External Temperature Sensor Connector (Optional)
CN2
SMBus Connector
CN3
Digital I/O Connector
CN4
Internal USB 3.0 Port 1 and 2 Connector
CN5~CN6
LAN2~LAN1 External LED Connectors
CN7
DVI-D Connector
CN8, CN11, CN12
Internal USB 2.0 Port 6 and 7, Port 8 and 9, Port 2 and 3 Connectors
CN9
VGA Connector
CN10
DisplayPort Connector (Optional)
CN13
Front Panel Connector
CN14, CN17
External USB 3.0 Port 4 and 3 Connectors
CN15
Internal Mouse Connector
CN16
Internal Keyboard Connector
FAN1
System Fan Connector
FAN2
Auxiliary Fan Connector
FAN3
CPU Fan Connector
LAN1
Ethernet Port 1 (i217LM)
LAN2
Ethernet Port 2 (i210AT)
PRINT1
Parallel Port
SATA1~SATA6
Serial ATA 3.0 port 1~port 6 Connectors
COM1~COM5
COM1~COM5 Connectors
AUDIO1
Audio Connector
ATX2
Power Connector
DIMM1~DIMM2
DDR3/L DIMM Connectors

SHB130 LGA1150 Full-size CPU Card
10 Board and Pin Assignments
2.4.1 External Temperature Sensor Connector (CN1) (Optional)
This is a 2-pin connector for external temperature sensor (NTC thermistor) interface.
The thermistor value should be 10K and its B value is 3435K.
2.4.2 SMBus Connector (CN2)
The SMBus interface is available through this connector.
2.4.3 Digital I/O Connector (CN3)
The board is equipped with an 8-channel digital I/O connector that meets requirements
for a system customary automation control. The digital I/O can be configured to control
cash drawers and sense warning signals from an Uninterrupted Power System (UPS), or
perform store security control. You may use software programming to control these
digital signals.
Pin
Signal
1
Sensor Input
2
GND
Pin
Signal
1
CLOCK
2
N.C
3
GND
4
DATA
5
+5V
Pin
Signal
Pin
Signal
1
DIO 1
2
DIO 8
3
DIO 2
4
DIO 7
5
DIO 3
6
DIO 6
7
DIO 4
8
DIO 5
9
GND
10
GND

SHB130 LGA1150 Full-size CPU Card
Board and Pin Assignments 11
2.4.4 Internal USB 3.0 Connector (CN4)
The CN4 is an internal connector for USB 3.0 interface.
2.4.5 LAN External LED Connectors (CN5 and CN6)
The LAN2 and LAN1 external LED interfaces are available through CN5 and CN6,
respectively.
2.4.6 DVI-D Connector (CN7)
The board comes with a 24-pin box-header for DVI-D interface.
Pin
Signal
Pin
Signal
1
VBUS0
2
SSRX0-
19
VBUS1
3
SSRX0+
18
SSRX1-
4
GND
17
SSRX1+
5
SSTX0-
16
GND
6
SSTX0+
15
SSTX1-
7
GND
14
SSTX1+
8
USB0-
13
GND
9
USB0+
12
USB1-
10
ID
11
USB1+
Pin
Signal
1
+3.3V
2
LINK_ACT LED(-)
3
100, Low Active
4
+3.3V
5
1000, Low Active
Pin
Signal
Pin
Signal
1
Data2-
2
Data2+
3
GND
4
N.C.
5
N.C.
6
DDC CLK
7
DDC Data
8
N.C.
9
Data1-
10
Data1+
11
GND
12
N.C.
13
N.C.
14
+5V
15
GND
16
HPD
17
Data0-
18
Data0+
19
GND
20
N.C.
21
N.C.
22
GND
23
Clock+
24
Clock-

SHB130 LGA1150 Full-size CPU Card
12 Board and Pin Assignments
2.4.7 Internal USB 2.0 Connectors (CN8, CN11 and CN12)
These are internal connectors for USB 2.0 interfaces.
CN8(USB port 6 and 7),
CN11(USB port 8 and 9),
CN12(USB port 2 and 3)
2.4.8 VGA Connector (CN9)
The CN9 is a 15-pin D-Sub connector which is commonly used for CRT monitor.
Pin
Signal
Pin
Signal
1
USB_PWR
2
USB_PWR
3
USB -
4
USB -
5
USB +
6
USB +
7
GND
8
GND
10
GND
Pin
Signal
Pin
Signal
1
Red
2
Green
3
Blue
4
N.C.
5
GND
6
DETECT
7
GND
8
GND
9
VCC
10
GND
11
N.C.
12
DDC DATA
13
Horizontal Sync
14
Vertical Sync
15
DDC CLK

SHB130 LGA1150 Full-size CPU Card
Board and Pin Assignments 13
2.4.9 DisplayPort Connector (CN10) (Optional)
DisplayPort (digital display interface standard) is available through connector CN10.
Note that connector CN10 is co-layout with VGA port (CN9).
Pin
Signal
1
LANE0
2
GND
3
LANE0#
4
LANE1
5
GND
6
LANE1#
7
LANE2
8
GND
9
LANE2#
10
LANE3
11
GND
12
LANE3#
13
HDMI_DET
14
GND
15
AUX CH
16
GND
17
AUX CH#
18
Hot Plug Detect
19
GND
20
DP_PWR(3.3V)

SHB130 LGA1150 Full-size CPU Card
14 Board and Pin Assignments
2.4.10 Front Panel Connector (CN13)
Power LED
Pin 1 connects anode(+) of LED and pin 5 connects cathode(-) of LED. The power LED
lights up when the system is powered on. The pin 3 is defined as GND.
External Speaker and Internal Buzzer
Pin 2, 4, 6 and 8 connect the case-mounted speaker unit or internal buzzer. While
connecting the CPU board to an internal buzzer, please set pin 2 and 4 closed; while
connecting to an external speaker, you need to set pins 2 and 4 opened and connect the
speaker cable to pin 8(+) and pin 2(-).
Power On/Off Button
Pin 9 and 10 connect the power button on front panel to the CPU board, which allows
users to turn on or off power supply.
System Reset Switch
Pin 11 and 12 connect the case-mounted reset switch that reboots your computer
without turning off the power switch. It is a better way to reboot your system for a longer
life of system power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control panel. LED flashes
when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front
panel HDD LED, pin 13 is assigned as cathode(-) and pin 14 is assigned as anode(+).
Pin
Signal
1
PWRLED+
2
EXT SPK-
3
GND
4
Buzzer
5
PWRLED-
6
N.C.
7
N.C.
8
EXT SPK+
9
PWRSW-
10
PWRSW+
11
HW RST-
12
HW RST+
13
HDDLED-
14
HDDLED+