AXIOMTEK CAPA880 Series User manual

4 9418E880000E
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
Installing Fan
Note:
Be careful not to over tighten
the screws as it can damage
the processor or the CPU
board.
The processor needs specially designed heatsink and fan assembly to cool
down and ensure sufficient air flow inside your system. After applying
thermal grease on the processor and installing it on the socket, please
place heatsink and fan assembly on top of it. Match the four screws to the
fixing holes on the board. Then screw tightly the heatsink and CPU fan
assembly onto the board. Also make sure the fan cable is plugged to fan
connector (CN1).
Quick Start
The basic procedures required to power on CAPA880:
(1). Require power at minimum 5A. Ensure that power supply is
OFF before connecting to CAPA880 and that all necessary
peripheral devices are plugged properly.
(2). Ensure all of the jumpers are at default settings; especially
JP5 (1-2 close).
(3). Firmly install DDR3 memory modules into connector SODIMM1
until fully seated.
(4). Firmly insert power to ATX1.
(5). Install a momentary on/off button/switch onto CN2, pin 9 and
10.
(6). Turn on the power supply.
(7). Press the on/off button/switch to power on CAPA880
CN2
CAPA880 Series Quick Installation Guide
9418E880000E 1
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
Checklist
CPU board x1 Product information CD x1
USB cable x1 Quick installation guide x1
Audio cable x1 COM cable x1
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Connectors
Connector Description
CN1 Fan Connector
CN2 Front Panel Connector
CN3 LVDS Connector
CN4 SATA Power Connector
CN5 Inverter Connector
CN6 COM1 Wafer Connector
CN7 Audio Connector
CN8 USB 2.0 Wafer Port 5 and 6
CN9 Digital I/O Connector
CN10 (Optional) Power Connector
CN11 SMBus Connector
CN12 Ethernet Port 1 and Port 2
CN14 USB 3.0 Port 0 and 1
CN15 USB 2.0 Port 2 and 3
CN16 HDMI Connector
CN17 VGA Connector
ATX1 ATX Power Connector
BAT1 CMOS Battery Connector
SATA1 Serial ATA Port
SCN1 Full-size PCI-Express Mini Card Connector
SCN2 ZIO Expansion Connector
SODIMM1 DDR3 SO-DIMM Connector
CAPA880 Intel®CoreTM Processor
Famil
y
3.5”
Board

2 9418E880000E
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
Jumper Settings
Before applying power to the CAPA880, please make sure all of the
jumpers are in factory default positions.
Jumper Description Setting
JP1 LVDS +3.3V/+5V/+12V Voltage Selection
Default: +3.3V 5-6 Close
CN6 Pin 1: DCD 3-5 Close
JP2 COM1 Data/Power Selection
Default: RS-232 Data CN6 Pin 8: RI 4-6 Close
JP3 Restore BIOS Optimal Defaults
Default: Normal Operation 1-2 Close
JP5 Auto Power On
Default: Disable 1-2 Close
Note: Please refer to the CAPA880 series product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.
Board Layout
Top View
9418E880000E 3
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
Bottom View
Side View