AXIOMTEK AX92320 User manual

AX92320
4-port Gigabit 802.3at PCI Express
PoE Card
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or rights of any
third party, or any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
June 2018, Version A1
Printed in Taiwan

iii
ESD Precautions
The boards have integrated circuits sensitive to static electricity. To avoid damaging chipsets
from electrostatic discharge, observe the following precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help to discharge any static electricity on a
human body.
When handling boards and components, wear a grounding wrist strap available from
most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®is a trademark of Intel Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Section 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Features...............................................................................................1
1.3 Specifications......................................................................................2
1.4 Dimensions..........................................................................................3
Section 2 Connectors .................................................. 5
2.1 Connectors..........................................................................................5
2.1.1 PD Power Indicator (CN1)........................................................................... 5
2.1.2 LAN1 ~ LAN4 Connector (CN 3)................................................................. 6
2.1.3 Board ID (SW1)........................................................................................... 6
2.1.4 12/24V Power Input (For IEEE 802.3at, ATX1)........................................... 7
Chapter 3 AX PoE Manager Software ...................... 9
3.1 Management software.........................................................................9
3.2 AX PoE Manager ...............................................................................10
3.3 Menu Bar............................................................................................11
3.3.1 File............................................................................................................. 12
3.4 Menu List ...........................................................................................13
3.4.1 Information ................................................................................................ 13
3.4.2 Control....................................................................................................... 14
APPENDIX A Board ID Mapping .............................. 15

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
Introduction 1
Section 1
Introduction
This section contains general information and detailed specifications of the AX923204-port
Gigabit 802.3at PCI express PoE Card, including the following sections:
General Description
Features
Specifications
Dimensions
1.1 General Description
The AX92320 PoE (Power over Ethernet) card supports four independent Gigabit Ethernet
ports, providing up to 30W at 54 VDC of power per port. Its wide operating temperature range
supports integration for vision inspection applications in harsh environments. In addition, the
AX92320 features have been designed to reduce cost, simplify installation and facilitate
maintenance for your machine vision solutions.
1.2 Features
High performance
PCI Express x4 compliant
4 independent GbE LANs
Supports 9.5KB Jumbo Frame and IEEE 1588
Compliant with IEEE802.3at to deliver 30W at 54 VDC per port
Up to 20/120W PoE power from PCIe bus/6-pin ATX power connector
0°C to +60°C wide operating temperature range
PoE power management software
Support LAN port smart on/off

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
2 Introduction
1.3 Specifications
Lan Chip
Intel® Ethernet Controller I210-AT
All LAN support 10/100/1000Mbps
PCIe Switch
PI792X2G608
Golden finger
One for standard PCIex4 interface
PSE controller
Linear Tech LTC4266
Dimensions
W 168mm x D 111 mm
OS support
Windows® 7, WES7, Windows® 10, Windows® 10 IoT (32/64-bit)
Environmental
Operating temperature: 0°C ~ 60°C
Operating humidity 5% ~ 95% non-condensing
Storage temperature: -20°C ~ 80°C
Certifications
CE / FCC
Power Requirements
Power from PCIe slot: (Max. 20W POE power output)
2.1A @ +12V
1.2A @ +3.3V
Power from the ATX power connector: (Max. 120W POE power output)
12A @ +12V or 6A @ +24V
1.2A @ +3.3V (from PCIe slot)
30W@54VDC power output (per port)

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
Introduction 3
1.4 Dimensions
Component Side
Solder Side

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
4 Introduction
This page is intentionally left blank.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
Connectors 5
Section 2
Connectors
2.1 Connectors
Connectors connect the board with other parts of the system. Loose or improper connection
might cause malfunctions. Make sure all connectors are properly and firmly connected.
The following table lists the function of each connector on the AX92320.
Connectors
Label
CN1
2.1.1
CN3
2.1.2
SW1
2.1.3
ATX1
2.1.4
2.1.1 PD Power Indicator (CN1)
When a LAN port is currently active, its corresponding PD power indicator will light up.
Pin
Signal
G1
LAN Port1
G2
LAN Port2
G3
LAN Port3
G4
LAN Port4

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
6 Connectors
2.1.2 LAN1 ~ LAN4 Connector (CN 3)
Pin
Description
LED1
Active LED (Amber)
LED2
Link LED (10/100-Green; 1000-Amber)
2.1.3 Board ID (SW1)
Default board ID setting is 0 (0x000)
ID4
ID3
ID2
ID1
Board ID
0
0
0
0
0
0
0
0
1
1
0
0
1
0
2
0
0
1
1
3
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
0
0
8
1
0
0
1
9
1
0
1
0
10
1
0
1
1
11
1
1
0
0
12
1
1
0
1
13
1
1
1
0
14
1
1
1
1
15
Note: On: 1, Off: 0
Board ID default: 0

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
Connectors 7
2.1.4 12/24V Power Input (For IEEE 802.3at, ATX1)
Pin
Signal
1
+12V / +24V
2
+12V / +24V
3
+12V / +24V
4
Ground (GND)
5
Ground (GND)
6
Ground (GND)

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
8 Connectors
This page is intentionally left blank.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
AX PoE Manager Software 9
Chapter 3
AX PoE Manager Software
3.1 Management software
AX PoE Manager is a highly integrated software management system that provides an
easy-to-use application programming interface.
Software Structure
AX PoE Manager is one of intelligent software to manage PoE (Power over Ethernet) device,
ranging from physical layer connectivity, communication layer protocol, middleware API, high
level software for management. AX PoE Manager is the ideal solution integration with specific
embedded systems. The powerful and useful PoE managed abilities suit for various vertical
applications.
Key features of AX PoE Manager include: Local Hardware Monitor.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
10 AX PoE Manager Software
3.2 AX PoE Manager
The PoE Manager belongs to PoE (Power over Ethernet) monitor and manage software. The
PoE manager major task is to routinely monitor each PoE port’s power consumption.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
AX PoE Manager Software 11
3.3 Menu Bar
On the top of main screen, you can see menu bar. Select any items in this bar to go to the sub
menus.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
12 AX PoE Manager Software
3.3.1 File
Polling rate
Set the polling rate to monitor PoE power consumption.
5 sec
10sec
30 sec
60 sec
Exit Close the PoE manager

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
AX PoE Manager Software 13
3.4 Menu List
The menu list is located on the left frame of the screen, contains all of monitoring and
controlling functions.
3.4.1 Information
The Information menu displays the following items information:
General
General
Show the power consumption and status for each PoE ports.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
14 AX PoE Manager Software
3.4.2 Control
The Control menu allows user to set configuration of the following items:
Chip
Chip
Control each port and chip status and reset

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
Board ID Mapping 15
APPENDIX A
Board ID Mapping
This section will guide you to solve the common issues when running our application.
1. Board ID Collision
Cause:
The board ID of the PoE card is mapping to physical SMBus address. If the duplicate
SMBus addresses are in the same bus, this will cause communication collision.
Situation:
1. “AXPoE Manager”pops up the “Cannot find any AXPoE device on this system”
message.
2. The number of devices is not as expected in “AXPoE Manager”
Solution:
1. Please check that the PoE card was installed properly on the system.
2. If the step1 is fine, these may be caused by board ID collision, please follow the
step as below to fix it.
3. Run the “AXPoEDiagnosis.exe”tool to show the available board ID in the current
system, and please change the board ID to these available board ID.

AX92320 4-port Gigabit 802.3at PCI Express PoE Card
16 Board ID Mapping
This page is intentionally left blank.