Axxess AXi-CANBOX1 User manual

AXi-CANBOX1 INSTALLATION MANUAL
COMPATIBLE PLUG & PLAY WIRING HARNESSES
PLEASE REVIEW THIS INSTALLATION MANUAL
CAREFULLY BEFORE BEGINNING ANY WORK
AXi-JAGVIM-C AXi-GIG-C AXi-GIGCAM-C
AXi-GIG-AV-C AXi-GIG-CAMAV-C AXi-QUAD-C
AXi-QUAD1-CAM-C AXi-QUAD1-AV-C AXi-RRVIM-C
AXi-SYNC-C AXi-SYNCAM10-C AXi-SYNCAM12-C
AXi-UCT22-C AXi-UCT22-CAM-C AXi-UNI-C
AXi-UNI-CAM-C

2
Table Of Contents
………………………………….……….
IMPORTANT WARNING
This product includes instructions for installation which must be carefully
followed. The instructions are worded in such a manner to assume that the
installer is capable of completing these type of electronic installations. If you
are unclear as to what you are instructed to do or believe that you do not
understand the instructions so as to properly and safely complete the
installation you should consult a technician who does have this knowledge and
understanding.
Failure to follow these instructions carefully and to install the interface as
described could cause harm to the vehicle or to safety systems on the vehicle.
Interference with certain safety systems could cause harm to persons as well.
PRECAUTIONS.……………………………………..…...3
WIRING LEGEND AND DESCRIPTION…………4-5
ASSIGNMENT OF SWITCHES…………….………….6
FEATURE PROGRAMMING…….……….………...7-8
DEVICE SETTINGS MENU…..…………………..…...9
FAQ……………………………………………….....…….10
QUICK START GUIDE ………………………...…11-12

3
………………………………….……….
PRECAUTIONS: Please read before you start the installation
Please study these instructions carefully before installing
AXXESS.i interface.
Many new vehicles use low-voltage or data-bus systems
that can be damaged by test lights and logic probes. Test
all circuits with a digital multi-meter before making
connections.
Do not disconnect the battery if the vehicle has an
anti-theft-coded radio, unless you have the radio code.
If installing an external push button switch, check with
the customer about where to install the switch.
To avoid accidental battery drainage turn off the interior
lights or remove the dome light fuse.
Roll down a window to avoid being locked out of the car.
Use of this product in a manner different to its intended
way of operation may result in property damage, personal
injury, or death.
Set Parking brake.
Remove the negative battery cable.
Protect fenders before starting.
Using protective blankets to cover front seats, interior of
the vehicle and center console.
Always install a fuse 6-12 inches away from AXXESS.i
interface, 5 amp fuse should be used.
Always secure AXXESS.i interface with Velcro or double
side tape to prevent rattling of the interface.
When securing AXXESS.i interface make sure that panels
can be closed back easily.
Use electrical tape on all you connections and splices, do
not leave any exposed connections.
Route all wires along factory harnesses, try not to drill or
make any unnecessary holes.
Make sure you are not connecting to any data wires;
always check your connections with a multi-meter.
Always use help of a professional installer to prevent any
damage to the vehicle or AXXESS.i interface.

4
Wiring legend and description
DO NOT CONNECT WIRES BELOW WHEN USED IN
CONJUNCTION WITH AXi PLUG AND PLAY HARNESS.
Red Wire: Constant +12V power input.
Must connect to constant power source, can usually be found at
the main power plug on the back of the radio or at another source
where AXi-CANBOX1 is installed. Do not connect to accessory or
ignition power source. Connecting to +12V constant power will
not drain battery, interface goes into sleep mode after key is
removed and doors are locked.
Black Wire: Ground connection.
Must connect to a ground source, can usually be found at the
main power plug on the back of the radio or at another source
where AXi-CANBOX1 is installed. Do not connect to chassis
ground or radio chassis.
CAN Wires: If installation is going to be performed without plug
and play harness CAN High and CAN Low Wires must be cut and
the AXi-CANBOX1 will be installed in line.
Orange Wire: CAN High radio side.
Connect orange wire to radio side of vehicles CAN High wire.
Green Wire: CAN Low radio side.
Connect green wire to radio side of vehicles CAN Low wire.
Yellow Wire: CAN High car side.
Connect yellow wire to car side of vehicles CAN High wire.
White Wire: CAN Low car side.
Connect white wire to car side of vehicles CAN Low wire.
Blue Wire: External activation switch.
Used only in certain applications.
Purple Wire: Not used, do not connect.
Micro USB: Used for programing and updating
AXi-CANBOX1 must be programmed with a vehicle specific
software before installation starts. Please see pages 7-9 for
details.
Status LED: Blinks when CAN wires properly connected.

5
Wiring legend and description
Additional connections when AXi-CANBOX1 is installed
with AXi-UNI-CAM-C camera harnesses.
Connections in addition to wires shown on page 4.
Camera Input 1: Factory or aftermarket camera input.
Camera Input 2: Front camera input.
Camera Input 3: Left camera input.
Camera Input 4: Right camera input.
Camera Output: Common output of camera 1,2,3 and 4.
If vehicle is equipped with factory rear view camera, factory
rear view camera will be routed to camera input 1, and
camera output will be connect to camera input of factory
headunit, this will allow to installation of additional cameras to
factory headunit, such as front and side view cameras.
Video Input 1: Video input from aftermarket video source or
factory DVD player.
Video Input 2: Video input from aftermarket video source.
Video Output: Common video output of video input 1 and 2.
If vehicle is equipped with factory DVD player, factory DVD
player will be routed to video input 1, and video output will be
connect to video input of factory headunit, this will allow an
installation of additional video sources to factory headunit.
Fig.1

6
Assignment of Switches.
Switches are preset to OFF position by default. In a few
specific installation cases switches may need to be set to
ON position, in case where switches need to be set to
ON positing this information will be available in AXi
harness installation manual.
For most installations fig.2 and fig.3 shows correct
switch position.
To access switches remove cover by removing two
screws in each corner of AXi-CANBOX1
g.3
ON CTS
ON ON
OFF OFF
12
g.2

7
Feature Programming
All installations of AXi-CANBOX1 require
programming prior to installation.
Prior to starting an installation, features and setting of
AXI-CANBOX1 interface must be adjusted for the
interface to operate correctly. Vehicle specific software
must be flashed into the interface.
To update, please follow instructions below:
Download and install AXXESS.i online updater on your
computer.
There will be 3 components installed on your PC
1. AXXESS.i online updater
2. Database Connector
3. TeamViewer
AXXESS.i online updater is only compatible with
Microsoft Windows based PC.
After installation is complete go to your start menu
locate folder with AXXESS.i online updater and run the
program.
We have built in AXXESS.i Team Viewer feature and live
chat for tech support in case you have any question
during update and require immediate support.
On the bottom left corner of the AXXESS.i online
updater you will find a button for remote support.
Click remote support button and TeamViewer will open.
It will generate one time ID and Password
(ID and password changes every time program is open)
Provide us with this information and we will be able to
help you remotely if such help is required. See fig.6 on
page 8.

8
Connect AXi-CANBOX1 to your PC with micro USB cable.
(cable not supplied must be purchased separately)
Step One: Select make model year or click search to
show all vehicles.
Step Two: select vehicle software for installation.
Step Three: Click install.
If installing extra cameras click on setting button to open
up setting menu screen.
This is your initial view fig.5 shown below.
g.4

9
Device Settings Menu
Front Camera-Place check mark if installing aftermarket front view
camera. (make sure front camera doesn't have reverse image)
Rear Camera-Place check mark if installing aftermarket rear view
camera.
Left Camera-Place check mark if installing left side view camera.
Right Camera-Place check mark if installing right side view camera.
Video-In-Motion-Place check mark to enable video-in-motion
feature.
Refer to vehicle specific installation manual for camera operations
and controls.
If any changes are made, press ACCEPT button and all
settings will register to the AXi-CANBOX1.

10
FAQ
Q: I start the car but radio/screen/nav doesn't turn on?
A: please check that CAN wires are connected properly and
LED on AXi-CANBOX1 is blinking.
Q: I shift vehicle in reverse gear I get a blank screen
but no camera image on the screen?
A: In all installation cases of AXi-CANBOX1 camera input is
already present in a vehicle from factory, AXi-CANBOX1 only
activates this input. If blank screen is displayed when vehicle
in reverse, check camera RCA and power connection.
Q: When I try to use the camera while driving, the
screen goes blank and no camera is shown?
A: Make sure camera is connected to +12V Accessory power
and not to reverse lights.
Q: Video-In-Motion or Navigation-In-Motion is not
working when driving?
A: This features are designed for off-road use only and never
when operating vehicle on public roads, different makes and
models have different activation sequences, ex: press mute
button 4 times on the steering wheel, by activating video in
motion via activation sequence you are acknowledging that
you are either off road or in controlled environment away from
public roads.
Q: When vehicle is started it takes long for radio to boot
up?
A: AXi-CANBOX1 must be connected to constant power not
accessory power.

11
——————————————————————————————————————————————————————--
TEAR HERE
QUICK START GUIDE
Thank you for purchasing AXXESS.i AXi-CANBOX1
Video-In-Motion: This features is designed for off-road use only and
never when operating vehicle on public roads, different makes and
models have different activation sequences, ex: press mute button
4 times on the steering wheel, by activating video in motion via
activation sequence you are acknowledging that you are either
off-road or in controlled environment away from public roads.
Navigation-In-Motion: This features is designed for off-road use
only and never when operating vehicle on public roads, different
makes and models have different activation sequences, ex: press
mute button 4 times on the steering wheel, by activating navigation in
motion via activation sequence you are acknowledging that you are
either off-road or in controlled environment away from public roads.
Control-In-Motion: This features is designed for off-road use only
and never when operating vehicle on public roads, different makes
and models have different activation sequences, ex: press mute
button 4 times on the steering wheel, by activating control in motion
via activation sequence you are acknowledging that you are either
off-road or in controlled environment away from public roads.
Rear View Camera Input/Camera-In-Drive: if you have installed
a back-up camera, your aftermarket camera will turn on automatically
in reverse.
You can use the camera while in drive, please ask your installer for
details on operating this feature.
(AXi-CANBOX1 interface and Rear-View Camera In-Drive must be
configured by your installer for this feature to operate as described
above)
DISCLAIMER: WARNING!!! WARNING!!!
AXXESS.i is designed to be used only when the vehicle is immobilized.
The driver is responsible for maintaining full attention while operating
a motor vehicle. The removal or bypassing of safety features in
AXXESS.i products will result in termination of warranty. Using
AXXESS.i unit improperly may result in injury, citation or arrest by
authorities. Therefore Metra Electronics owners and employees are
not responsible for unauthorized use.
Get top quality OE integration interfaces on our website.