B-K lighting GARDEN STAR User manual

Hot SurfaceLow VoltageWarning
Standard Installation
GARDEN STAR (GR)
LOW VOLTAGE
Flammable
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before
replacing lamp/LED. Fixture gets HOT quickly!
Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Suitable for in-ground installation
IMPORTANT LISTINGS AND CERTIFICATIONS
5/64” Allen Wrench
Waterproof Wire Connectors
Mounting Hardware
Mallet or Sledge Hammer
TOOLS
NEEDED:
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL
ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RELEASE DATE
05/15/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2859-00
GR-E
GR-K

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASE DATE
05/15/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2859-00
2. Use a 5/16” allen wrench to loosen three (3) #8-32
stainless steel set screws (do not remove set
screws from fixture). Remove anchor base from
the fixture.
Finished Grade
1. Drive the stake into the ground with a mallet or a
small sledge hammer. Make sure the top is flush
with the finished grade.
3. Attach the anchor base to the threads on the stake.
Make sure the stake is secured in the ground.
6. Make watertight connections from remote
transformer to fixture leads using waterproof wire
connectors (not included). See wiring diagram.
Finished Grade
4. Pull low voltage, typically direct burial cable
throught the stake center where the hole is located
to make the connect with the fixture.
Ground wire connections is based off of local
code requirements.
7. Install fixture onto anchor base. Do not pinch
wiring. Secure fixture by tightening three (3)
stainless steel set screws on fixture knuckle using
a 5/64” allen wrench. Do not overtighten set
screws.
Remote
Transformer
HOT 12V
12V
Fixture
NEUTRAL
Remote
Transformer
WIRING DIAGRAM
For use with 12VAC remote transformer.
Remote Installation
Standard Installation