B-K lighting Tenaya 2 Series User manual

RELEASE DATE
4-10-17
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
3/16” Allen Wrench
Phillips Screwdriver
Level
Hammer
Waterproof Wire Nuts
Warning High Voltage Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Junction Box Power Supply
Compartment
Rebar Saddles
Exterior
Patented HydroLock®
Plate w/ Silicone
O-Ring
Interior
Patented HydroLock®
Plate w/ Silicone
O-Ring (not shown)
Stability Flange
Adjustment Posts
Tenaya2® and its features are covered in whole or in part by U.S. Patent No. 7,175,297; U.S. Patent No. 7,033,038;
U.S. Patent No. 6,254,258 B1; U.S. Patent No. 7,553,042; and U.S. Patent No. 7,560,148.
TENAYA2® SERIES
Housing Installation
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Temporary Cover

RELEASE DATE
4-10-17
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
TENAYA2® SERIES
Housing Installation
Housing Rough-In
On bottom
Drill through sides
1. Connect branch conduit connectors (By Others)
to the junction box using either the threaded
conduit entries on the bottom of the junction
box or through holes drilled into the sides of the
junction box.
Do not remove the yellow temporary cover
during rough-in.
2. Place housing in hole. Align junction box in the
path of the conduit trench.
3. Insert (4) pieces of ½” EMT conduit through the
Stability Flange™. Hammer into substrate until
secure.
Leave sufficient clearance to elevate housing
to finished grade.
Top of yellow temporary
cover level to
finished grade.
4. Raise housing on EMT to finished grade (top of
yellow temp cover). Use bubble level on yellow
temporary cover to aid in leveling housing.
5. When top of yellow temporary cover is level
with finished grade, tighten screws on Stability
Flange™ to secure housing to EMT. Remove
excess EMT as needed.
6. Connect the conduit to the conduit connectors.
Soil Prep
A. Determine Soil Type by referencing DIG-IT
Guide. Prep soil according to DIG-IT Guide.
See www.bklighting.com/dig-it for more
information.
J-Box
Conduit
Trench 24”
Dia.
B. Determine Soil Type by referencing DIG-IT
Guide.
C. Dig hole 24” wide and 27-33” deep.
Conduit
Trench
Excavated
for Housing
D. Prep soil according to DIG-IT Guide.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

RELEASE DATE
4-10-17
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
10. Wipe O-ring clean of debris before re-inserting
patented HydroLock® plate on to junction box.
Turn HydroLock® plate clockwise to lock in place
under pins.
B. For a drive-over installation, fill the hole around
the fixture housing to 12” below the finished
grade with clean fill dirt and tamp carefully to
prevent settling of fixture. Pour concrete and
finish as required flush with the top surface of
the Yellow Installation Cover.
Note: Drive-over rated for 55,000 lbs. GVW
(Standard flat lens rated for 35,000 lbs.
GVW)
A. For soil installation, fill and tamp soil to the
appropriate height leaving room for sod,
pavers, etc. to be level with the top of the
Yellow Installation Cover.
Soil installation is NOT Drive-over rated!
Concrete/Drive-over
Soil
7. Per DIG-IT Guide, backfill the gap between the
bottom of housing and bottom of hole with
sand for drainage.
8. Rotate patented HydroLock® plate counter
clockwise to allow notch in HydroLock® plate to
clear pins on junction box. Pull to remove.
9. Pull branch circuit wiring and external dimming
controls into junction box. Make watertight
connections using waterproof wire connectors
(provided) to leads on the interior patented
HydroLock® plate. See wiring diagram.
TENAYA2® SERIES
Housing Installation
Housing Rough-In (Continued)
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
LINE (BLACK)
COM (WHITE)
Hydrolock
Plate
GROUND (GREEN)
Black
White
Hydrolock
Plate
Green
Driver
White
Black
White
Blue
Green
LINE
COM
GROUND
Orange
Orange
Brown
Blue
Black
Gray
FIXTURE
FIXTURE
Green
Green
DIM + (RED)
DIM - (ORANGE)
DIM +
DIM -
WIRING DIAGRAM

TENAYA2® SERIES
Component Installation
Warning High Voltage Hot Surface
3/16”, 7/64” & 1/8” Allen Wrench
Level
Hammer
Phillips Screwdriver
NEEDED
FOR
INSTALLATION:
By Others
RELEASE DATE
12-6-16
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Tenaya2® and its features are covered in whole or in part by U.S. Patent No. 7,175,297; U.S. Patent No. 7,033,038; U.S.
Patent No. 6,254,258 B1; U.S. Patent No. 7,553,042; and U.S. Patent No. 7,560,148.
Driver
Enclosure
Solid Silicone
Faceplate Gasket
OptiLock™
and Optic
Driver Input
Driver Output
Optical Chamber
Faceplate
Patented Leveling Collar
Concrete Pour Collar
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
1A. For soil installation, clear soil around temporary
cover to prevent debris falling into the housing.
Remove temporary cover.
1B. For a concrete installation, break through the
disposable Yellow Installation Cover with a claw-
hammer or pry-bar, then grasp the cover and pull
straight up to leave a smooth, finished edge.
NOTE: Temporary Cover is recyclable.
For Soil
For Concrete
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS

Fixture Installation
TENAYA2® SERIES
Component Installation
up to 30° of rotation
Faceplate
screw
locations
2. Place the Patented Leveling Collar on the four
adjustable posts. Each adjustable post can be
raised or lowered using a Phillips screwdriver.
Leveling collar also allows for 30° of rotation to
align faceplate screws with one another. When
collar is level, and faceplate screw holes are
aligned to final position, secure the collar with
the four hex nuts provided.
3. Place the driver enclosure in the driver
compartment. Connect the primary/input cable
from the driver to the patented HydroLock®
plate located in the housing as shown.
4. Connect the output/secondary cable on the
driver to the bottom of the optical chamber.
5. If your Tenaya2® comes with optional
accessory holder, see “Relamping with
Accessory Holder” to remove and install
source.
To aim the OptiLock™ inside the optical
chamber horizontally 360°, rotate the optical
chamber to desired direction.
8. For Optional Internal Cutoff: Place internal
cutoff louver in the top of the optical chamber
in the desired direction of cutoff and install
faceplate as normal.
Optional Internal Cutoff
7. Before Installation of faceplate, clean solid
silicone faceplate gasket (see arrows) and collar
of debris for a proper seal.
FAILURE TO DO THIS STEP WILL CAUSE
FIXTURE TO FAIL AND VOID PRODUCT
WARRANTY.
9. Install the faceplate using 3/16” Allen wrench
and torque the faceplate screws in a cross
pattern to 25 in-lbs.
RELEASE DATE
12-6-16
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
6. To aim the OptiLock™ inside the optical
chamber vertically, loosen the four (4) #10-
24 screws using 1/8” Allen wrench and tilt
OptiLock™ to desired vertical direction. Tighten
all screws when aiming is complete.

RELEASE DATE
12-6-16
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
3. Remove optic by twisting gently, then pulling
away.
2. Pull accessory holder from clips on accessory
bracket.
Relamping with Accessory Holder
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
TENAYA2® SERIES
Relamping & Accessories
1. Install the faceplate using 3/16” Allen wrench
and torque the faceplate screws in a cross
pattern to 25 in-lbs.
5. Remove optic holder by loosening two (2)
#4-40 screws using a 0.05” Allen wrench.
6. Carefully remove LED module from heatsink.
Do not pull on connector or wiring. Handle
with care.
Fragile! Do not pull on connector or wiring.
Handle with care.
7. Use small pick tool to push connector off
LED board through two small slots behind
connector. Once loose, lift connector upwards
and off board.
8. Place new LED module onto heatsink. Press
connector straight downwards into slot on
module to snap into place.
Connector will only fit in one direction.
4. Loosen (2) #6-32 set screws holding accessory
bracket to OptiLock™ as shown. Remove
accessory holder from OptiLock™.
9. Replace optic holder by tightening two (2)
#4-40 screws using a 0.05” Allen wrench to
secure to OptiLock™.

17. Install the faceplate using 3/16” Allen wrench
and torque the faceplate screws in a cross
pattern to 25 in-lbs.
TENAYA2® SERIES
Relamping & Accessories
RELEASE DATE
12-6-16
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
11. Install reflector by placing in LED reflector
holder, then twisting gently to the right under
tabs.
12. Place accessory holder onto tabs on accessory
bracket, lined up with notches in holder.
10. Place accessory holder on OptiLock™, lining
up holes in bracket on OptiLock™. Tighten (2)
#6-32 set screws to secure accessory bracket to
OptiLock™ as shown.
15. Before Installation of faceplate, clean solid
silicone faceplate gasket (see arrows) and collar
of debris for a proper seal.
FAILURE TO DO THIS STEP WILL CAUSE
FIXTURE TO FAIL AND VOID PRODUCT
WARRANTY.
13. If your Tenaya2® comes with optional
accessory holder, see “Relamping with
Accessory Holder” to remove and install
source.
To aim the OptiLock™ inside the optical
chamber horizontally 360°, rotate the optical
chamber to desired direction.
16. For Optional Internal Cutoff: Place internal
cutoff louver in the top of the optical chamber
in the desired direction of cutoff and install
faceplate as normal.
Optional Internal Cutoff
14. To aim the OptiLock™ inside the optical
chamber vertically, loosen the four (4) #10-
24 screws using 1/8” Allen wrench and tilt
OptiLock™ to desired vertical direction. Tighten
all screws when aiming is complete.

TENAYA2® SERIES
Accessories
RELEASE DATE
2-1-17
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
3. Insert up to (2) accessories into the accessory
holder. Accessories should rest on lip of
accessory holder.
NOTE:
1) Insert any accessory lens with the smooth
side toward the LED.
2) If using a honeycomb baffle, position it
farthest from the LED.
Accessory Replacement
4. Place accessory holder onto tabs on accessory
bracket over optic.
1. Pull accessory holder from accessory bracket. 2. Optic should remain.
5. Tabs on accessory bracket keep accessory
holder in place. Accessories are gravity held in
place.

RELEASE DATE
12-6-16
REFERENCE NUMBER
INS-2145-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
3. Using a 3/32” Allen wrench, loosen the two sets
screws on the faceplate to allow accessory to
rotate freely.
4. Accessory can rotate 360° independently of
faceplate.
5. When set in final position, tighten two set
screws.
2. Install the faceplate using 3/16” Allen wrench
and torque the faceplate screws in a cross
pattern to 25 in-lbs.
Rock Guard w/
Optical Opening
Rock Guard Half Dome Glare Shield
1. Before installation of faceplate, clean solid
silicone faceplate gasket (see arrows) and collar
of debris for a proper seal.
FAILURE TO DO THIS STEP WILL CAUSE
FIXTURE TO FAIL AND VOID PRODUCT
WARRANTY.
Faceplates with Accessories
TENAYA2® SERIES
Optional Faceplates
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS