babcockdavis Lume-A-Lite BEM-DSH1-10 User manual

1
©2020 Babcock-Davis,
Inc.
Rev 8/2020
Installation, Operation
+ Maintenance Manual
Lume-A-Lite™ HANDRAIL STRIP
Model(s): BEM-DSH1-10
GENERAL DESCRIPTION
Photoluminescent egress path marking systems are an
important life safety requirement in current building
codes. These systems allow for the safe and quick
evacuation of buildings in the case of an emergency.
They provide a routing system that is not dependent
on electrical power that can easily be followed in dark
and smoke-filled exit pathways.
Introduction + Safety
Please read the complete instructions carefully before beginning any work. To ensure proper
installation and performance of the product, the following actions must be completed by the
installing contractor. Failure to do so will affect product warranty.
Transportation + Storage
oInspect all shipments and materials for missing or damaged components and hardware.
oMaterial must be stored in a clean, dry location.
Preparation
Please read the complete instructions carefully before beginning any work.
oThe temperature of the product being installed and the surface it is being installed on must be at
least 60 degrees.
oSurfaces must be clean, smooth, and non-porous. Install a sample piece of the strip material for 24
hours on the application surface to ensure that the strip adheres properly before doing a complete
project installation.
oGloves should be used when handling and installing the strip to prevent injury.
GENERAL SAFETY PRECAUTIONS Improper selection, installation, or use can cause personal injury or property damage. It
is solely the responsibility of the user, through its own analysis to select products suitable for their specific application
requirements, ensure they are properly maintained, and limit their use to its intended purpose. Follow proper local,
state, and federal regulations for proper installation and operation requirements.

2
©2020 Babcock-Davis, Inc
.
Rev 8/2020
Installation, Operation & Maintenance
Safe-T-Lume™ HANDRAIL STRIP
Model(s): BEM-DSH1-10
INSTALLATION
The handrail strip shall be placed on the top surface of the handrail for its entire length, this
includes extensions and newel post caps. Where handrails or extensions bend or turn corners,
the strip must not have a gap of more than 4 inches (figure 1).
oThoroughly clean the surface area where the strip will
be installed with a dry cloth and a non-residue
cleaning compound to remove and loose particles
and dirt. For oily surfaces, isopropyl alcohol works
well for surface preparation. Surfaces must be dry
and dust free.
oMeasure the handrail to determine the proper length
of the strip and then cut with scissors. The ends of
the strip that will be a starting or ending segment
need to be lightly beveled with a file to create a
smooth transfer from the strip to the railing.
oPeel a portion of the backing from the handrail strip
without touching the adhesive.
oPlace the strip at your starting point on the railing and
firmly press onto the handrail. Peel more backing
from the adhesive strip as you go. Make sure the strip is straight and properly centered along
the top length of the handrail. Be sure that the strip has full contact with the railing, this may
involve using a rubber roller to ensure proper adhesion.
OPERATION
oExposure Requirements: The minimum amount of exposure to artificial ambient illumination is 60
minutes from the following:
•One-foot candle (11 Lux) of florescent, incandescent, or LED light
oThe control of the ambient illumination necessary to charge the luminous egress-path-
marking system should be restricted to authorized personnel only.
oFailure to supply the above minimum exposure can prevent the luminous egress-path-
marking from performing as intended.
Figure 1

3
©2020 Babcock-Davis, Inc
.
Rev 8/2020
Installation, Operation & Maintenance
Safe-T-Lume™ HANDRAIL STRIP
Model(s): BEM-DSH1-10
oNo specific building surface treatment is required for the luminous egress-path-marking
system to function properly.
oReliable external illumination is always required during building occupancy.
MAINTENANCE
oMaintain by cleaning as needed to prevent dirt, etc. from inhibiting the performance of the
photoluminescent properties.
oThe strip may be cleaned by using a damp cloth with mild, non-abrasive cleaners. Do not us
highly alkaline or acidic cleaners. Rinse after applying cleaners and wipe with a clean cotton
cloth to dry.
Questions?
For more information on installation, repair, or replacement, please visit www.Babcockdavis.com or call
(888)-412-3726