babcockdavis Lume-A-Lite BEM-SLE100 Instruction manual

1
©2020 Babcock-Davis
, Inc.
Rev 8/2020
Installation, Operation
+ Maintenance Manual
Lume-A-Lite™ EXIT SIGNS
Model(s): BEM-SLE100/BEM-SE100
GENERAL DESCRIPTION
Photoluminescent egress path marking systems are an
important life safety requirement in current building
codes. These systems allow for the safe and quick
evacuation of buildings in the case of an emergency.
They provide a routing system that is not dependent
on electrical power that can easily be followed in dark
and smoke-filled exit pathways.
Introduction + Safety
Please read the complete instructions carefully before beginning any work. To ensure proper
installation and performance of the product, the following actions must be completed by the
installing contractor. Failure to do so will affect product warranty.
Transportation + Storage
oInspect all shipments and materials for missing or damaged components and hardware.
oMaterial must be stored in a clean, dry location.
Preparation
oThese signs are for interior use only and are suitable for a temperature range of +50 to 100
degrees Fahrenheit.
oThese signs are rated for a visibility of 100 feet when activated by a minimum five (5) foot-
candlelight source and can be used in both high-level and low-level applications.
GENERAL SAFETY PRECAUTIONS Improper selection, installation, or use can cause personal injury or property damage. It
is solely the responsibility of the user, through its own analysis to select products suitable for their specific application
requirements, ensure they are properly maintained, and limit their use to its intended purpose. Follow proper local,
state and federal regulations for proper installation and operation requirements.

2
©2020 Babcock-Davis, Inc
.
Rev 8/2020
Installation, Operation & Maintenance
Lume-A-Lite™ EXIT SIGNS
Model(s): BEM-SLE100/BEM-SE100
Note:
oWhen installing into drywall or concrete block, use expansion sets to ensure a firm grip.
oIt is prudent to confirm that the mounting bracket location on the wall or ceiling is appropriate (i.e. provides
adequate clearances between assembled exit sign and other objects, such as walls, ceiling, or swinging doors) by
holding the assembled exit sign in the mounting bracket and holding the bracket in the desired location on the
wall or ceiling. All clearances should then be confirmed as acceptable prior to the mounting bracket being fixed
to the wall or ceiling.
oAfter installation is complete, the visibility of the sign from all potential viewing angles and distances should be
confirmed.
INSTALLATION
One-Sided Wall Mount Installation
The photoluminescent exit sign shall be placed above doors through which occupants must
pass to complete the exit path.
1. Mark pilot hole locations on wall using
mounting holes in the back plate.
2. Drill pilot holes in wall surface.
3. Level and mount back plate to wall using
mounting hardware.
4. Insert frame screws through mounting holes
into pilot holes in wall and tighten.
5. Snap exit face plate to back plate.
6. Attach plastic filler strips (top and sides).
7. Apply right and/or left arrows to face of sign.

3
©2020 Babcock-Davis, Inc
.
Rev 8/2020
Installation, Operation & Maintenance
Lume-A-Lite™ EXIT SIGNS
Model(s): BEM-SLE100/BEM-SE100
Projection Wall Mount – One or Two-Sided Installation
The photoluminescent exit sign shall be placed above doors through which occupants must pass to
complete the exit path.
1. Mark pilot hole locations on wall using mounting holes in mounting bracket.
2. Drill pilot holes in wall surface.
3. Level and mount bracket to wall using mounting hardware.
4. Snap exit face plate to back plate.
5. Attach side of exit sign into mounting
bracket
6. Attach plastic filler strips (top and side).
7. Apply right and/or left arrows to face of sign.
Projection Ceiling Mount – One or Two-Sided
Installation
The photoluminescent exit sign shall be placed above doors through which occupants must pass to
complete the exit path.
1. Mark pilot hole locations on ceiling using mounting holes in mounting bracket.
2. Drill pilot holes in ceiling surface.
3. Level and mount bracket to ceiling using
mounting hardware.
4. Slide and snap exit face plate to back plate.
5. Attach top of exit sign into mounting
bracket.
6. Attach plastic filler strips (sides).
7. Apply right and/or arrows to face of sign.
OPERATION
oExposure Requirements: The minimum amount of exposure to artificial ambient illumination
is 60 minutes from the following:
•One-foot candle (11 Lux) of florescent, incandescent, or LED light
oThe control of the ambient illumination necessary to charge the luminous egress-path-
marking system should be restricted to authorized personnel only.

4
©2020 Babcock-Davis, Inc
.
Rev 8/2020
Installation, Operation & Maintenance
Lume-A-Lite™ EXIT SIGNS
Model(s): BEM-SLE100/BEM-SE100
oFailure to supply the above minimum exposure can prevent the luminous egress-path-
marking from performing as intended.
oNo specific building surface treatment is required for the luminous egress-path-marking
system to function properly.
oReliable external illumination is always required during building occupancy.
MAINTENANCE
oMaintain by cleaning as needed to prevent dirt, etc. from inhibiting the performance of the
photoluminescent properties.
oThe strip may be cleaned by using a damp cloth with mild, non-abrasive cleaners. Do not use
highly alkaline or acidic cleaners. Rinse after applying cleaners and wipe with a clean cotton
cloth to dry.
Questions?
For more information on installation, repair or replacement, please visit www.Babcockdavis.com or call
[phone]