Baker Hughes Masoneilan SVi 1000 User manual

Masoneilan*
SVi*1000 Positioner
Instruction Manual (Rev G)
BHGE Data Classification: Public

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
2 | BHGE
About this Guide
This instruction manual applies to the following instruments and approved software:
SVi1000*
with firmware version 2.2.1 (for use with HART®5) or 3.1.1 (for use with HART®7).
with ValVue 3 version 3.20.0 or greater
with a HART®Communicator with DD published for SVi1000
The information in this manual is subject to change without prior notice.
The information contained in this manual, in whole or part, shall not be transcribed or copied without BHGE’s written
permission.
In no case does this manual guarantee the merchantability of the positioner or the software or its adaptability to a specific
client needs.
Please report any errors or questions about the information in this manual to your local supplier or visit www.bhge.com
DISCLAIMER
THESE INSTRUCTIONS PROVIDE THE CUSTOMER/OPERATOR WITH IMPORTANT PROJECT-SPECIFIC REFERENCE
INFORMATION IN ADDITION TO THE CUSTOMER/OPERATOR’S NORMAL OPERATION AND MAINTENANCE PROCEDURES.
SINCE OPERATION AND MAINTENANCE PHILOSOPHIES VARY, BHGE (BAKER HUGHES, A GE company LL AND ITS
SUBSIDIARIES AND AFFILIATES) DOES NOT ATTEMPT TO DICTATE SPECIFIC PROCEDURES, BUT TO PROVIDE BASIC
LIMITATIONS AND REQUIREMENTS CREATED BY THE TYPE OF EQUIPMENT PROVIDED.
THESE INSTRUCTIONS ASSUME THAT OPERATORS ALREADY HAVE A GENERAL UNDERSTANDING OF THE REQUIREMENTS
FOR SAFE OPERATION OF MECHANICAL AND ELECTRICAL EQUIPMENT IN POTENTIALLY HAZARDOUS ENVIRONMENTS.
THEREFORE, THESE INSTRUCTIONS SHOULD BE INTERPRETED AND APPLIED IN CONJUNCTION WITH THE SAFETY RULES
AND REGULATIONS APPLICABLE AT THE SITE AND THE PARTICULAR REQUIREMENTS FOR OPERATION OF OTHER
EQUIPMENT AT THE SITE.
THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT NOR TO PROVIDE FOR
EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE.
SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED
SUFFICIENTLY FOR THE CUSTOMER/OPERATOR'S PURPOSES THE MATTER SHOULD BE REFERRED TO BHGE.
THE RIGHTS, OBLIGATIONS AND LIABILITIES OF BHGE AND THE CUSTOMER/OPERATOR ARE STRICTLY LIMITED TO THOSE
EXPRESSLY PROVIDED IN THE CONTRACT RELATING TO THE SUPPLY OF THE EQUIPMENT. NO ADDITIONAL
REPRESENTATIONS OR WARRANTIES BY BHGE REGARDING THE EQUIPMENT OR ITS USE ARE GIVEN OR IMPLIED BY THE
ISSUE OF THESE INSTRUCTIONS.
THESE INSTRUCTIONS ARE FURNISHED TO THE CUSTOMER/OPERATOR SOLELY TO ASSIST IN THE INSTALLATION,
TESTING, OPERATION, AND/OR MAINTENANCE OF THE EQUIPMENT DESCRIBED. THIS DOCUMENT SHALL NOT BE
REPRODUCED IN WHOLE OR IN PART TO ANY THIRD PARTY WITHOUT THE WRITTEN APPROVAL OF BHGE.
Copyright
The complete design and manufacture of the SVi1000 Smart Valve Interface is the intellectual property of BHGE. All
information contained herein is believed to be accurate at the time of publication and is subject to change without notice.
Copyright 2017 by Baker Hughes, a GE company LLC. All rights reserved.
PN 720013363-779-0000 Rev. G

Masoneilan SVi1000 Positioner Instruction Manual =|3
© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
Document Changes
Version/Date Changes
B/10-2012 Changed Load Limits section Simplified Switch Installation diagram and added Cau-
tion about polarity.
Changed GEA number.
C/05-2013 Made changes to Figure 7 Rotary Kit Components
D/09-2013 Added cautions to reference Load Limits section in Install section. Changed Simplified
Installation drawing in Load Limits section. Added Cautions about Position Low and
Upper Limits.
Added text about the 4-20 retransmit galvanic isolation.
E/02-2014 Rework of the Load Limits section.
F/03-2016 Updated load limits section.
Updated wiring and general descriptions to include retransmit wiring and features.
Updated all references to ValVue to reflect on ValVue version 3, along with licensing
changes.
G/08-2017 Fixed mistakes in description of number of entry ports.
Fixed mistake in SV mapping for HART® Command 3.
Fixed mistake in Single Acting Air Delivery.
Added Compliance Voltage section.
Updated ValVue software download/install section.
Add a table for HART® Device Information in Specifications.
Added section for Troubleshooting Autotune.
Added section for Notes on Retransmit Board Upgrade Requirements.
Added section for Notes on Aggressiveness.
Added How Do I section.
Added section for DD Navigation.
Updated Fault Matrix.

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
4 | BHGE
Contents
1. Safety Information ............................................................................................................................................................................11
Documentation Symbols.............................................................................................................................................................11
SVi1000 Product Safety ...............................................................................................................................................................12
BHGE Documentation Resources for Masoneilan Products.......................................................................................13
Related Documentation for the SVi100 DTM.............................................................................................................13
2. Introduction .........................................................................................................................................................................................15
About This Manual..........................................................................................................................................................................15
Conventions Used in This Manual...................................................................................................................................15
ValVue Software..............................................................................................................................................................................16
System Requirements ..........................................................................................................................................................16
ValVue and SVi1000 DTM Trial Version ........................................................................................................................16
Operational Overview...................................................................................................................................................................17
SVi1000 Features............................................................................................................................................................................18
Functionality......................................................................................................................................................................................19
Modes...................................................................................................................................................................................................21
LED Light Functions .......................................................................................................................................................................23
3. Installation and Set Up ...................................................................................................................................................................25
Overview .............................................................................................................................................................................................25
SVi1000 Dimensions..............................................................................................................................................................26
Pre-Installation Issues ..................................................................................................................................................................27
Storage........................................................................................................................................................................................27
Unpacking..................................................................................................................................................................................27
ValVue and SVi1000 DTM Software Installation...............................................................................................................27
Masoneilan Software............................................................................................................................................................28
Mounting and Wiring ....................................................................................................................................................................31
Step 1: Mounting the SVi1000 ..........................................................................................................................................32
Step 2: Connecting the Tubing and Air Supply .........................................................................................................41
Step 3: Wiring the SVi1000.................................................................................................................................................42
4. Check Out and Power Up .............................................................................................................................................................47
Overview .............................................................................................................................................................................................47
Step 1: Inspect the Actuator, Linkages, or Rotary Adapter .........................................................................................48
Step 2: Verify Mounting and Linkage Adjustment ...........................................................................................................48
Step 3: Checking the Magnet ....................................................................................................................................................48
Perform a Visual Inspection...............................................................................................................................................48
Use ValVue to Check Magnet Position..........................................................................................................................49
Step 4: Checking the Air Supply ...............................................................................................................................................49
Step 5: Verify Wiring Connections...........................................................................................................................................50
Step 6: Configuration ....................................................................................................................................................................51
Auto Find Stops .......................................................................................................................................................................51
Open Stops Adjustments ....................................................................................................................................................52
Tuning ..........................................................................................................................................................................................52

Masoneilan SVi1000 Positioner Instruction Manual =|5
© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
5. Full Wizard .......................................................................................................................................................................................... 59
Full Wizard Screen ......................................................................................................................................................................... 59
Full Wizard Screen ................................................................................................................................................................. 59
Run the Full Wizard ............................................................................................................................................................... 62
6. Operation and Maintenance ....................................................................................................................................................... 65
Principle of Operation................................................................................................................................................................... 65
Physical and Operational Description .................................................................................................................................. 66
Electronics Module ................................................................................................................................................................ 66
Pneumatic Module................................................................................................................................................................. 67
SVi1000 Maintenance and Repair .......................................................................................................................................... 68
Adjusting I/P Zero................................................................................................................................................................... 68
Repair by Replacement ............................................................................................................................................................... 68
Internal Diagnostics ...................................................................................................................................................................... 68
FAILSAFE Mode........................................................................................................................................................................ 68
Upgrading Firmware..................................................................................................................................................................... 68
7. Specifications, Spare Parts and References ....................................................................................................................... 69
Physical and Operational Specifications ............................................................................................................................. 69
Spare Parts ........................................................................................................................................................................................ 74
Notes on Retransmit Board Upgrade Requirements ............................................................................................74
8. Using the Digital Interfaces ........................................................................................................................................................ 77
Overview.............................................................................................................................................................................................77
Hand Held Communicator ......................................................................................................................................................... 79
SVi1000 HART® Commands ..................................................................................................................................................... 80
ValVue.................................................................................................................................................................................................. 83
SVi1000 DD Navigation................................................................................................................................................................ 84
9. Wiring Theory for an SVi1000 .................................................................................................................................................... 85
Introduction....................................................................................................................................................................................... 85
SVi1000 Setups................................................................................................................................................................................ 85
Split Range Applications.............................................................................................................................................................. 86
System Connections Considerations .................................................................................................................................... 87
Wiring Guidelines............................................................................................................................................................................ 88
Grounding Practices ............................................................................................................................................................. 88
Compliance Voltage in Single Drop Current Mode................................................................................................. 89
Wire Size and Conduit.......................................................................................................................................................... 90
HART® Physical Layer Compliance of the Control System......................................................................................... 91
Impedance Constraints....................................................................................................................................................... 91
Noise Constraints................................................................................................................................................................... 91
Cabling and Interconnection Requirements ............................................................................................................. 92
Capacitance vs. Length of Cable for HART®............................................................................................................. 92
HART® Filter Required for Certain Control System Output Circuits ............................................................... 92
10. Optional Switch Load Limits .................................................................................................................................................... 93
Output Switches.............................................................................................................................................................................. 93
Introduction .............................................................................................................................................................................. 93

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
6 | BHGE
Optional Retransmit Output ......................................................................................................................................................95
Introduction...............................................................................................................................................................................95
11. Air to Open and Air to Close Actuators ................................................................................................................................97
Actuator Action................................................................................................................................................................................97
12. SVi1000 Fault Matrix ................................................................................................................................................................. 101
Fault Matrix..................................................................................................................................................................................... 101
13. Air Supply Requirements .......................................................................................................................................................... 107
Air Supply Requirements.......................................................................................................................................................... 107
14. Adjusting Speed of Response ................................................................................................................................................ 109
Adjusting Speed of Response................................................................................................................................................. 109
15. Advanced Usage ......................................................................................................................................................................... 111
Technology to Maximize Savings and Process Performance................................................................................. 111
Tight Shutoff Application to Protect from Seat Erosion..................................................................................... 111
Tight Shutoff Application to High Pressure Liquid Letdown Valve Trim..................................................... 111
16. Determining an SVI Positioner Compliance Voltage in a Control System ........................................................ 113
Compliance Test Setup ............................................................................................................................................................. 113
17. Glossary ........................................................................................................................................................................................... 115
18. How Do I? ........................................................................................................................................................................................ 123
Getting Started Tasks ................................................................................................................................................................ 123
Common Tasks ............................................................................................................................................................................. 123

© 2017 Baker Hughes, a GE company, LLC. All rights reserved. Masoneilan SVi1000 Positioner Instruction Manual =|7
Figures
1 Operator Controls - Standard......................................................................................................................................... 19
2 Optional Digital Switches and Gauges....................................................................................................................... 20
3 Optional Position Retransmit .......................................................................................................................................... 20
4 SVi1000 LEDs.......................................................................................................................................................................... 23
5 Example LED Pattern .......................................................................................................................................................... 23
6 SVi1000 Components......................................................................................................................................................... 25
7 SVi1000 Dimensions With and Without Gauges ................................................................................................... 26
8 Download Center: Search for Valve 3......................................................................................................................... 28
9 Opening Dialog...................................................................................................................................................................... 28
10 Download Center: Search for SVi1000 DTM ............................................................................................................ 29
11 Opening Dialog...................................................................................................................................................................... 30
12 Rotary Kit Components ..................................................................................................................................................... 33
13 Camflex with Mounting Bracket (Side View) ............................................................................................................ 33
14 Rotary Mounting Bracket to Valve Actuator............................................................................................................ 34
15 Extension Shaft to the Valve Position Take-off Shaft .......................................................................................... 34
16 Camflex V-Seal ...................................................................................................................................................................... 37
17 Reciprocating Valve Mounting Bracket for Standard Lever............................................................................. 37
18 Magnet Holder and Standard Lever for Reciprocating Valves ....................................................................... 38
19 SVi1000 Take Off Rod Mounting.................................................................................................................................... 39
20 Ensure Position Linearity................................................................................................................................................... 40
21 SVi1000 Lever Installed to IM Assembly .................................................................................................................... 40
22 Air Ports..................................................................................................................................................................................... 41
23 Front Cover.............................................................................................................................................................................. 44
24 Connections to Electronics Module with Switches
(via Interface Board)............................................................................................................................................................ 44
25 Connections to Electronics Module with Position Retransmit
(via Interface Board)............................................................................................................................................................ 45
26 Open Stop Adjustment Screw......................................................................................................................................... 52
27 Preset Tuning Values .......................................................................................................................................................... 53
28 Configuration Selection Switch...................................................................................................................................... 53
29 Configuration Selection Switch...................................................................................................................................... 55
30 Full Wizard Screen: Device Info...................................................................................................................................... 60
31 Block Diagram with I/P Converter ................................................................................................................................ 65
32 Pneumatic Module............................................................................................................................................................... 67
33 Newer Serial Numbers....................................................................................................................................................... 74
34 Older Serial Number............................................................................................................................................................ 75
35 SVi1000 HART® Communicator Connections ........................................................................................................ 79

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
8 | BHGE
36 General Purpose Installation...........................................................................................................................................85
37 Split Range with Supplemental Power Supply - Non-Hazardous ..................................................................86
38 Simplified Switch Installation Drawing: Correct Configuration.......................................................................94
39 Simplified Switch Installation Drawing: Configuration Not Allowed .............................................................94
40 Simplified Retransmit Option Installation Drawing...............................................................................................95
41 ATO and ATC Action with Linear Positioner Characteristics.............................................................................98
42 ATO and ATC Action in Percentage of Positioner Characteristics..................................................................99
43 Compliance Voltage Test Setup.................................................................................................................................. 113

© 2017 Baker Hughes, a GE company, LLC. All rights reserved. Masoneilan SVi1000 Positioner Instruction Manual =|9
Tables
1 LED Light Patterns and Troubleshooting................................................................................................................... 23
2 Travel Sensor Alignment ................................................................................................................................................... 36
3 Reciprocating Valve Mounting Hole and Turnbuckle Length.......................................................................... 38
4 Air Supply Requirements................................................................................................................................................... 41
5 Actuator Settings Configuration Selection Switch Guidelines......................................................................... 54
6 Rough Guide to Effect s of Changing PID Values .................................................................................................. 56
7 Environmental Specifications......................................................................................................................................... 69
8 Operational Specifications............................................................................................................................................... 70
9 Input Signal and Power, Specifications...................................................................................................................... 71
10 Construction Material Specifications .......................................................................................................................... 71
11 System Connectivity............................................................................................................................................................ 72
12 Pneumatics Single Acting Standard Flow................................................................................................................. 72
13 SVi1000 Model Numbering .............................................................................................................................................. 72
14 HART® Device Information1........................................................................................................................................... 73
15 SVi1000 HART® Commands ........................................................................................................................................... 80
16 Command 48 Additional Status Return Bits ............................................................................................................ 81
17 Compliance Voltage for Single Channel Zener with 22 AWG Cable............................................................. 89
18 Compliance Voltage for Galvanic Isolator with 22 AWG Cable...................................................................... 89
19 Compliance Voltage for No Barrier with HART® Filter and Resistor and 18 AWG Cable................... 90
20 Fault Matrix ...........................................................................................................................................................................101
21 Tight Shutoff Parameters for High Pressure Liquid Letdown Trim..............................................................111
22 Expected Voltage Range at Positioner Terminals...............................................................................................114

This page intentionally left blank.

© 2017 Baker Hughes, a GE company, LLC. All rights reserved. Masoneilan SVi1000 Positioner Instruction Manual =| 11
1. Safety Information
This section provides safety information and defines the documentation symbols.
Documentation Symbols
SVi1000 instructions contain warnings, cautions and notes, where necessary, to alert you to safety related
or other important information. Read the instructions carefully before installing and maintaining your
instrument. Total compliance with all WARNING, and CAUTION notices is required for safe operation.
Indicates a potentially hazardous situation, which if not avoided could result in
serious injury.
Indicates a potentially hazardous situation, which if not avoided could result in
property or data damage.
Indicates important facts and conditions.
WARNING
CAUTION
NOTE

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
12 | BHGE
SVi1000 Product Safety
For SVi1000 positioners intended for use with industrial compressed air: Ensure that an adequate
pressure relief provision is installed when the application of system supply pressure could cause
peripheral equipment to malfunction. Installation must be in accordance with local and national
compressed air and instrumentation codes.
General installation, maintenance or replacement
Products must be installed in compliance with all local and national codes and
standards by qualified personnel using safe site work practices. Personal Protective
Equipment (PPE) must be used per safe site work practices.
Ensure proper use of fall protection when working at heights, per safe site work
practices. Use appropriate safety equipment and practices to prevent the dropping of
tools or equipment during installation.
Under normal operation, compressed supply gas is vented from the SVi1000 to the
surrounding area, and may require additional precautions or specialized installations.
Intrinsically Safe Installation
Products certified for use in intrinsically safe installations MUST BE:
Installed, put into service, used and maintained in compliance with national and local
regulations and in accordance with the recommendations contained in the relevant
standards concerning those environments.
Used only in situations that comply with the certification conditions shown in this
document and after verification of their compatibility with the zone of intended use
and the permitted maximum ambient temperature.
Installed, put into service and maintained by qualified and competent professionals
who have undergone suitable training for instrumentation used in such areas.
WARNING Before using these products with fluids/compressed gases other
than air or for non-industrial applications, consult the factory. This
product is not intended for use in life support systems.
WARNING Do not use damaged instruments.
WARNING Installation in poorly ventilated confined areas, with any potential
of gases other than oxygen being present, can lead to a risk of
personnel asphyxiation.
Use only genuine replacement parts which are provided by the manufacturer, to guarantee that the
products comply with the essential safety requirements of the European Directives.
Changes to specifications, structure, and components used may not lead to the revision of this manual
unless such changes affect the function and performance of the product.

Masoneilan SVi1000 Positioner Instruction Manual =|13
© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
BHGE Documentation Resources for Masoneilan Products
BHGE publishes several different resources for documentation on Masoneilan products:
Bench quick starts contain information related to configuration and testing in a bench
top environment.
Hardware quick starts contain installation information and other basic information
related to getting a device installed and very generally configured.
Hardware instruction manuals contain more complete information for configuration of
a device. This manual also includes information on background functionality and
special circumstances useful in installation, configuration and operation/
troubleshooting.
Software manuals contain more complete information for the software configuration
of a device. This manual also includes information on background functionality and
special circumstances useful in configuration and operation (including diagnostics and
their interpretation). These manuals represent the same source material as the online
help.
Handheld documents: Give the DD mappings for the product.
Check the website: https://www.geoilandgas.com/file-download-search.
Related Documentation for the SVi100 DTM
ValVue documentation: The SVi1000 DTM works inside various software (such as
PACTware), however it is designed to work best with out ValVue 3 software. See the
ValVue 3 help or GEA31426 Masoneilan Products ValVue 3 Software Manual.
SVi1000 online help.

This page intentionally left blank.

© 2017 Baker Hughes, a GE company, LLC. All rights reserved. Masoneilan SVi1000 Positioner Instruction Manual =| 15
2. Introduction
About This Manual
The SVi1000 Instruction Manual is intended to help an experienced field technician efficiently install and
setup an SVi1000. If you experience problems that are not documented in this guide, call your local
representative, go to www.bhge.com, contact our helpdesk at ([phone] or email
[email protected]. Sales offices are listed on the last page of this document.
The SVi1000 is a high performance, digital valve positioner that combines a local display with remote
communication and diagnostic capabilities. The SVi1000 offers a multitude of options that fulfills the
broadest range of applications. It also communicates using the HART®protocol.
The local user interface and LEDs enables local operations of calibration and configuration functions.
Remote operations can be performed with ValVue software or any HART®Registered host interface that has
been pre-loaded with the Device Description file (DD) for SVi1000.
Conventions Used in This Manual
Conventions used in this manual are as follows:
Uppercase, italicized letters are used when referencing a term used in the SVi1000
display window. For example, when indicating the term mode, as in setup mode, and
referring to the display/software operation the convention is to spell mode is all
uppercase letters: MODE.
Italics is used for emphasis on important items.
Fields where data is entered or user-entered data is italicized.
Actions performed on buttons, checkboxes, etc. appear bolded. For example: Click Done.

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
16 | BHGE
ValVue Software
This section generally discusses the ValVue software that can be used to configure the SVi1000 from a
HART®configured laptop.
NOTE A cloning feature is available for the SVi1000 positioner. Cloning
transfers the configuration and calibration parameters from one
device to another. Cloning operations are to be performed only by
BHGE personnel or qualified channel partners trained on properly
performing the cloning function. This feature is not available
during normal ValVue operation. Contact BHGE or a channel
partner for more information.
System Requirements
Minimum requirements for all versions of ValVue software are:
Windows®2003 Server (SP3), Windows®2008 Server (SP2), XP, Windows®7,
Windows®8, Windows®Server 2012
64 MB RAM
Hard drive available space 1 G
A serial or USB port connected to a HART®modem with appropriate cable (or
Bluetooth)
For software installation, a connection to the internet to download ValVue and the
SVi1000 DTM.
ValVue and SVi1000 DTM Trial Version
You must download the ValVue software and the SVi1000 DTM software, then install to configure and use
the SVi100. See “ValVue and SVi1000 DTM Software Installation” on page 27.
The SVi1000 DTM software and the ValVue software comes with a trial version of ValVue. For 60 days after
the initial installation, The ValVue software provides the FDT frame capability in which the SVi1000 DTM
software operates. The SVi1000 DTM software provides the capability of configuring, calibrating,
diagnosing, trending and much more. After the 60 day trial period ValVue must be registered for
continued use. The SVi1000 DTM software functionality includes:
Setup Wizard Remote display of valve position, actua-
tor pressure (s)
Set calibration parameters Set configuration parameters
Monitor status⁄error indicators Input/Output configuration
Remote calibration of the SVi1000 Remote configuration of the SVi1000
Remote operation of the SVi1000 Backup and restore configuration
Trend setpoint, valve position, actuator
pressure

Masoneilan SVi1000 Positioner Instruction Manual =|17
© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
Operational Overview
The SVi1000 is a smart electro-pneumatic positioner that receives a 4 - 20 mA electrical position setpoint
signal from the controller and compares the position setpoint input signal to the valve position feedback
sensor. The difference between the position setpoint and position feedback is analyzed by the position
control algorithm that sets a servo signal for the I/P converter. The output pressure of the I/P is amplified
by a pneumatic relay that drives the actuator. Once the error between the setpoint and the valve position
feedback is within range, no other correction is applied to the servo signal in order to maintain valve
position.
The local user interface and LEDs provide configuration or calibration mode in all operating
environments.
The optional position retransmit version transmits the actual position via 4 - 20 mA signal to a supervisory
system.

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
18 | BHGE
SVi1000 Features
The SVi1000 positioner (see Figure 1 on page 19) is suitable for installation indoors or outdoors, and in a
corrosive industrial or marine environment and is equipped with the following features:
Extreme accuracy and reliability
Extreme digital precision
Preset values for quick configuration
Automated valve commissioning
Precise, quick, responsive control of valve position
One model for rotary or reciprocating valves
Local operation⁄calibration⁄configuration with a local user interface and LEDs
Compatible with air-to-close or air-to-open actuators
Non-contact magnet coupled (Hall Effect) position sensing for rotary and reciprocating
control valves
Sealed housing with no moving shafts, no shaft penetration, and fully potted
electronics
Digital switches (optional)
Position retransmit (optional)
Split range capability
User-adjustable response times
Configurable High and Low Position Limits
Characterize stroke (An accumulated value of 100% travel = 1 stroke. The travel does
not need to occur in one movement.):
Linear
Equal Percentage 50:1 and Equal Percentage 30:1
Quick Opening
11 Point Custom Characterization
Camflex*Percentage
Valve Position Autotuning (not required if presets used)
Optimized performance regardless of actuator size
Linearity compensation for actuator linkages with ValVue software
User-configurable Tight Shutoff at Adjustable Input Signal
HART®compatible
HART®remote operation, calibration, and configuration using ValVue software or a
HART®handheld communicator, and any HART®compatible host

Masoneilan SVi1000 Positioner Instruction Manual =|19
© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
Functionality
All connections to electronic module in the unit are made through the interface board. The SVi1000
standard interface board has a terminal block with screw connectors.
Optionally, you can order a unit configured with two digital switches or with 4 - 20 mA position retransmit
output.
Figure 1 shows the standard interface and lists below the operator controls for all SVi1000 interfaces.
Figure 1 Operator Controls - Standard
Auto Find Stops Button and
LED 1
Cancel/ Status Button and
LED 4
Upper Stop Button and LED
2
Ground
Auto Tune Button and LED 3 Configuration Selection
Switch
4- 20 mA Input Signal Open Stop Adjustment
Screw
1
5
2
6
3
7
4
8
1
2
3
4
5
6
7
8

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.
20 | BHGE
Figure 2 shows the optional switch interface board and optional gauges.
Figure 2 Optional Digital Switches and Gauges
Figure 3 shows the optional position retransmit interface board and optional gauges.
Figure 3 Optional Position Retransmit
Solid State
Solid State Switch
SW #1 (Optional)
(Optional)
Gauges
(Optional)
Switch SW #2
Ground
4- 20 mA
Input Signal
4- 20 mA
Output Signal (optional)
Gauges
(Optional)