Baker Hughes Masoneilan SVI FF User manual

Masoneilan™
SVI™FF Digital Positioner
Quick Start Guide (Rev. F)
Baker Hughes Data Classication: Public

2 | © 2021 Baker Hughes Company. All rights reserved.
About this Guide
This Quick Start Guide applies to the SVI FF instrument and supported software:
with Firmware version 1.0.0.1 or higher
with ValVue™ version 3.0
with handheld communicator with DD published for SVI FF
All information contained herein is believed to be accurate at the time of publication and is subject to
change without notice.
The information contained in this manual, in whole or part, shall not be transcribed or copied without
Baker Hughes’ written permission.
In no case does this manual guarantee the merchantability of the positioner or the software or its
adaptability to a specic client needs.
Please report any errors or questions about the information in this manual to your local supplier or
visit valves.bakerhughes.com. .
DISCLAIMER
THESE INSTRUCTIONS PROVIDE THE CUSTOMER/OPERATOR WITH IMPORTANT PROJECT-
SPECIFIC REFERENCE INFORMATION IN ADDITION TO THE CUSTOMER/OPERATOR’S
NORMAL OPERATION AND MAINTENANCE PROCEDURES. SINCE OPERATION AND
MAINTENANCE PHILOSOPHIES VARY, BAKER HUGHES COMPANY (AND ITS SUBSIDIARIES
AND AFFILIATES) DOES NOT ATTEMPT TO DICTATE SPECIFIC PROCEDURES, BUT TO
PROVIDE BASIC LIMITATIONS AND REQUIREMENTS CREATED BY THE TYPE OF EQUIPMENT
PROVIDED.
THESE INSTRUCTIONS ASSUME THAT OPERATORS ALREADY HAVE A GENERAL
UNDERSTANDING OF THE REQUIREMENTS FOR SAFE OPERATION OF MECHANICAL AND
ELECTRICAL EQUIPMENT IN POTENTIALLY HAZARDOUS ENVIRONMENTS. THEREFORE,
THESE INSTRUCTIONS SHOULD BE INTERPRETED AND APPLIED IN CONJUNCTION WITH
THE SAFETY RULES AND REGULATIONS APPLICABLE AT THE SITE AND THE PARTICULAR
REQUIREMENTS FOR OPERATION OF OTHER EQUIPMENT AT THE SITE.
THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN
EQUIPMENT NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN
CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER
INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT
COVERED SUFFICIENTLY FOR THE CUSTOMER/OPERATOR’S PURPOSES THE MATTER
SHOULD BE REFERRED TO BAKER HUGHES.
THE RIGHTS, OBLIGATIONS AND LIABILITIES OF BAKER HUGHES AND THE CUSTOMER/
OPERATOR ARE STRICTLY LIMITED TO THOSE EXPRESSLY PROVIDED IN THE CONTRACT
RELATING TO THE SUPPLY OF THE EQUIPMENT. NO ADDITIONAL REPRESENTATIONS OR
WARRANTIES BY BAKER HUGHES REGARDING THE EQUIPMENT OR ITS USE ARE GIVEN
OR IMPLIED BY THE ISSUE OF THESE INSTRUCTIONS.
THESE INSTRUCTIONS ARE FURNISHED TO THE CUSTOMER/OPERATOR SOLELY TO ASSIST
IN THE INSTALLATION, TESTING, OPERATION, AND/OR MAINTENANCE OF THE EQUIPMENT
DESCRIBED. THIS DOCUMENT SHALL NOT BE REPRODUCED IN WHOLE OR IN PART
WITHOUT THE WRITTEN APPROVAL OF BAKER HUGHES.
Copyright
All information contained herein is believed to be accurate at the time of publication and is subject to
change without notice.
Copyright 2021 by Baker Hughes Company. All rights reserved. PN 720023977-888- 0000 Rev. F.

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 3

4 | © 2021 Baker Hughes Company. All rights reserved.
Document Changes
Version/Date Changes
B/12-14 Updated headers and footers.
Made a few changes to Quick Start section Changed ES-776
to Rev J.
C/02-15 Changed ES-776 to Rev. K and to Declaration of Conformity
D/03-17 Changed ES-776 to Rev. L.
E/02-20 Changed ES-776 to Rev. M. Rebranded to
Baker Hughes formats. Added Product Num-
bering section.
Added Determining Device Descriptor and Firmware Versions
AP Label section.
Updated Mounting the SVI FF on Rotary Valves section.
F/07-21 ES-776 instructions removed.

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 5
Table of Contents
About this Guide...................................................................................... 2
Document Changes................................................................................. 4
Safety Information................................................................................... 6
Safety Symbols.............................................................................................. 6
SVI FF Product Safety ............................................................................. 7
General installation, maintenance or replacement ........................................................ 7
Intrinsically Safe Installation..........................................................................................7
Masoneilan Help Contacts...................................................................... 8
Product Numbering................................................................................. 9
Device Descriptor and Firmware ........................................................... 9
Installation and Set Up.......................................................................... 12
Pushbuttons and Local Display........................................................... 13
Mounting the SVI FF on Rotary Valves................................................ 14
Mounting the SVI FF on Reciprocating Valves ................................... 15
Wiring the SVI FF................................................................................... 16
FF Environment Minimum Settings ..................................................... 17
Step 1: Set Air Action ..................................................................................................17
Step 2: Set Control Tuning. ......................................................................................... 17
Step 3: Set Characterization Type............................................................................... 17
Step 4: Enter a Device Address and Device Tag......................................................... 17
Step 5: Run Find Stops and then run Autotune...........................................................17
Example Conguration ......................................................................... 18
Step 1: Install the Positioner on the Valve...................................................................18
Step 2: Set Tag and Address.......................................................................................18
Step 3: Basic Conguration.........................................................................................19
Step 4: Run Find Stops METHOD ..............................................................................20
Step 5: Run Auto Tune METHOD ...............................................................................20
Downloads ............................................................................................. 20
Hazardous Location Installation .......................................................... 21

6 | © 2021 Baker Hughes Company. All rights reserved.
Safety Information
This section provides safety information and denes the documentation symbols.
Safety Symbols
Indicates a potentially hazardous situation,
which if not avoided could result in serious
injury or death.
WARNING
NOTE
Indicates important facts and conditions.
CAUTION Indicates a potentially hazardous situation,
which if not avoided could result in
instrument or property damage, or data loss.
SVI FF instructions contain warnings, cautions and notes, where necessary, to alert you to
safety related or other important information. Read the instructions carefully before installing
and maintaining your instrument. Total compliance with all WARNING, and CAUTION notices is
required for safe operation.

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 7
SVI FF Product Safety
For SVI FF positioners intended for use with industrial compressed air:
Ensure that an adequate pressure relief provision is installed when the application of system
supply pressure could cause peripheral equipment to malfunction. Installation must be in
accordance with local and national compressed air and instrumentation codes.
General installation, maintenance or replacement
• Products must be installed in compliance with all local and national codes and standards
by qualied personnel using safe site work practices. Personal Protective Equipment
(PPE) must be used per safe site work practices.
• Ensure proper use of fall protection when working at heights, per safe site work
practices. Use appropriate safety equipment and practices to prevent the dropping of
tools or equipment during installation.
• Under normal operation, compressed supply gas is vented from the SVI FF to the
surrounding area, and may require additional precautions or specialized installations.
Intrinsically Safe Installation
Products certied as explosion proof or ame proof equipment or for use in intrinsically
safe installations MUST BE:
• Installed, put into service, used and maintained in compliance with national and local
regulations and in accordance with the recommendations contained in the relevant
standards concerning those environments.
• Used only in situations that comply with the certication conditions shown in this
document and after verication of their compatibility with the zone of intended use and
the permitted maximum ambient temperature.
• Installed, put into service and maintained by qualied and competent professionals who
have undergone suitable training for instrumentation used in such areas.

8 | © 2021 Baker Hughes Company. All rights reserved.
WARNING Before using these products with uids/compressed gases other than
air or for non-industrial applications,consult the factory. This product
is not intended for use in life support systems.
WARNING Under certain operating conditions, the use of damaged instruments
could cause a degradation of the performance of the system which
may lead to personal injury or death.
WARNING Installation in poorly ventilated conned areas, with any potential
of gases other than oxygen being present, can lead to a risk of
personnel asphyxiation.
Use only genuine replacement parts which are provided by the manufacturer, to guarantee
that the products comply with the essential safety requirements of the European Directives.
Changes to specications, structure, and components used may not lead to the revision
of this manual unless such changes a󰀨ect the function and performance of the product.
Masoneilan Help Contacts
• Email: [email protected]
• Phone: 888-SVI-LINE (888-784-5463)

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 9
Product Numbering
Refer to Masoneilan SVI FF Safe Use instructions ES-776 available in:
valves.bakerhughes.com/resource-center
Determining Device Descriptor and Firmware
Versions AP Label
It is useful to track the version of the Device Descriptor (DD) and rmware version in use on
your DCS and positioner respectively. This is of value in troubleshooting system issues that
can arise when initially installing and later upgrading Masoneilan and non-Masoneilan system
components. There are several di󰀨erent ways to access the required information.
Figure 1 shows the unit tag that comes attached to the unit.
Figure 1 - Unit Tag

10 | © 2021 Baker Hughes Company. All rights reserved.
The tag lists the following items:
ID: Unique factory-set identier for the
device.
Tag: User-dened. This can be
changed for the specic application.
Factory Node Address: Lists the
factory-set eld bus node address.
Device Manufacturer: The six digits
comprise the rst part of the ID and
Tag. Used to identify the DD.
Device Type: A four digit code. Device and Minimum DD Revision:
Represents the original rmware
revision ashed during manufacture.
This DD may have been upgraded
since installation.
Communications: Lists the protocol in
use.
Diagnostics: Lists the level of
diagnostics with which the device
was shipped. This may have been
upgraded since installation.
Pneumatic Train: Single Acting or
Double Acting.
Pneumatic Flow: Standard Flow or
High Flow.
Display: Indicates whether the LED
display and pushbuttons are installed.
Housing: Aluminum only.
The actual device ID in this case is constructed according to the following
formula:
004745 – which is the manufacturer identier for Masoneilan
0008 – which is the device type for SVI FF positioner
______________ - 14 underscore characters
XXXXXXXX – the eight number string for the device part number as shown in the
picture below (rst two letters are ignored)
From the Live List information presented in the DCS or in the Communication DTM
(Figure 2).
Figure 2 - Device ID: Live List

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 11
From the DTM, when open in connected mode (note: some hosts may not support this
feature):
Figure 3 - Device ID: DTM
Firmware versions can also be viewed using the:
SVI FF DTM on the Positioner tab. The rmware revision is Software Revision
(Figure 4). Where the rst digit, here 1, represents the DD Revision.
Figure 4 - Positioner Tab
By creating/printing the SVI FF Conguration Report by:
1. Selecting View > Network View > Topology Pane.
2. Selecting the positioner, right-clicking and selecting Additional Functions >
Report.
Handheld by selecting Online > SVI FF Device > Resource Block > Device >
Identication.

12 | © 2021 Baker Hughes Company. All rights reserved.
Installation and Set Up
The steps necessary to complete the SVI FF installation and software setup are outlined in
Table 1.
Table 1 - SVI FF Installation Steps
Step
No. Procedure
1Attach mounting bracket to the actuator.
2Install the SVI FF magnetic assembly (rotary valves only).
3 Assemble the SVI FF on the bracket that is mounted to the valve actuator.
4Connect the pneumatic tubing to the SVI FF.
5 Connect the air supply to the SVI FF.
6 Connect the positioner to the H1 segment by installing the SVI FF wiring.
7Congure/calibrate using ValVue, the SVI FF DTM or a handheld using the DD.
See Example Conguration on page 18 for a general example.
WARNING Failure to adhere to the requirements listed may
cause loss of life and property.
Before installing, using, or carrying out any
maintenance tasks associated with this
instrument, READ ALL THE INSTRUCTIONS
CAREFULLY.

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 13
Pushbuttons and Local Display
Pushbuttons
The local pushbuttons are located behind a hinged cover, directly below the display window. To
open the cover loosen the screw and swing the cover down. Always re-fasten the cover after
use to protect the pushbuttons from environmental contamination. The pushbuttons perform the
following:
Left Button - Marked with *, permits you to select or accept the value or parameter
option currently displayed.
Middle Button - Marked –, permits you to move back through the menu structure to
the previous item in the menu or decrement the value currently shown in the digital
display. When used to decrease a displayed value, holding the button down causes
the value to decrease at a faster rate.
Right Button - Marked +, permits you to move forward through the menu structure
to the next item in the menu, or to increment the value currently shown in the digital
display. When used to increase a displayed value, holding this button down causes
the value to increase at a faster rate.
CAUTION The display is limited to values between 0 and
100. Therefore, the display may show a value for
the actual setpoint that is not valid if the setpoint
is above 100 or below 0.
NOTE When an exclamation point (!) appears in the SVI FF
display window, it indicates that there is instrument status
available.

14 | © 2021 Baker Hughes Company. All rights reserved.
Mounting the SVI FF on Rotary Valves
Travel Sensor Alignment
Table 2 shows the general guidelines for travel sensor alignment. Review the table prior to
installing the SVI FF on a rotary valve actuator for proper alignment of the magnet. Alignment is
required for proper Hall sensor operation.
Table 2 - Travel Sensor Alignment
Rotary
Mounting
System
Stroke Direction
(An accumulated value
of 100% travel = 1
stroke. The travel does
not need to occur in one
movement):
Magnet
Orientation
Valve
Position
Sensor
Counts
(TB: RAW_POSITION)
Rotary <60° Rotation
Clockwise or
counterclockwise
rotation
(0°)
Closed (0%) 0 +/- 1000
>60° Rotation
Clockwise with
increasing setpoint
(-45°)
Full Open
or
Full Closed
-8000 +/- 1500
or
+8000 +/- 1500
>60° Rotation
Counter Clockwise
rotation with increasing
setpoint
(+45°)
Full Open
or
Full Closed
-8000 +/- 1500
or
+8000 +/- 1500
General Rule
for other
con gurations
Any amount of
rotation Clockwise or
counterclockwise
(0°)
50%
Travel
(Mid-Stroke)
0 +/- 1000

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 15
Mounting the SVI FF on Reciprocating Valves
Table 3 - Reciprocating Valve Mounting Hole and Turnbuckle Length
Actuator
Size
Masoneilan
Stroke Mounting
Hole
Lever
Hole
Turnbuckle
Length
6 and 10 0.5 - 0.8”
(12.7 - 20.32 mm) A A 1.25” (31.75 mm)
10
0.5 - 0.8”
(12.7 - 20.32 mm)
A A 1.25”
(31.75 mm)
10 >0.8 – 1.5”
(20.32 - 41.5 mm) B B 1.25” (31.75 mm)
16 0.5 - 0.8”
(12.7 - 20.32 mm) BA2.90” (73.66 mm)
16 >0.8 – 1.5”
(20.32 - 41.5 mm) C B 2.90” (73.66 mm)
16 >1.5 – 2.5”
(41.5 - 63.5 mm) D C 2.90” (73.66 mm)
23 0.5 - 0.8”
(12.7 - 20.32 mm) BA5.25” (133.35 mm)
23 >0.8 – 1.5”
(20.32 - 41.5 mm) C B 5.25” (133.35 mm)
23 >1.5 – 2.5”
(41.5 - 63.5 mm) D C 5.25” (133.35 mm)

16 | © 2021 Baker Hughes Company. All rights reserved.
Wiring the SVI FF
Figure 5 - Connections to Electronics Module (via Terminal Board)
AI PV 1-5 VDC
(Not used in this release)
I/P Connector
Conguration Lock
Jumper
9 - 32 V Foundation
Fieldbus Input
Signal (polarity
independent)
Shield
(on FF unit housing)
Display
Remote Position
Sensor Input
Discrete Input
(Activated
using SMARTs
Assistant)
Discrete Out

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 17
FF Environment Minimum Settings
The general steps necessary to complete the SVI FF conguration and software setup are
outlined in Figure 6.
Figure 6 - Quick Start Conguration
Step 1: Set Air Action
Step 2: Set Control Tuning by choosing
Single or Double Acting and setting tuning
type. Autotune is recommended, Custom
Requires entering your own values.
Step 3: Set Characterization Type.
Custom requires entering your own values.
Step 4: Enter a Device Address and Device Tag.
Step 5: Run Find Stops and then run Autotune.

18 | © 2021 Baker Hughes Company. All rights reserved.
Example Conguration
Step 1: Install the Positioner on the Valve
See Installation and Set Up on page 12.
Step 2: Set Tag and Address
Using NI Congurator:
1. Import DD/CFF les.
CAUTION Do not navigate to the NI DD folder and copy the
DD le onto itself.
2. Right-click on the device, select Set Tag, follow the prompts to enter a
Tag.
3. Click Set.
CAUTION Do not deactivate the Set to OOS mode check-
box. The block must be in OOS to change the
Tag.
4. Right-click on the device, select Set Address, follow the prompts to enter
an Address.
CAUTION If the device is at the temporary address range
(248 (0xF8)- 251 (OxFB)), you must set the
address outside of that range.
5. Click Set.
CAUTION Do not deactivate the Set to OOS mode check-
box. The block must be in OOS to change the
Address.

© 2021 Baker Hughes Company. All rights reserved. Masoneilan SVI FF Digital Positioner Quick Start Guide | 19
Step 3: Basic Conguration
This section serves as an example where the AO block and TB block are congured. However,
there are a number of combinations that can be congured. This discussion is valid if the
positioner is controlled by the AO block.
1. For the Transducer block set:
ACTUATOR_3.ACT_FAIL_ACTION_1 = either 1. Valve Closed (most
common) or 2. Valve Open
ACCESSORY.REMOTE_SENSOR = 0, if remote sensor is not in use (internal
Hall sensor is used)
ACTIVATE_CONTROL_SET to one of:
CHAR_SELECTION.TYPE to one of:
See Transducer Block Parameters in the SVI FF instruction manual for further
settings.
2. For the AO block review/set as below:
0: Activate
Custom Control Set
(required for Autotune
as well - most common)
1: Activate
Control Set 1
(Slowest)
2: Activate
Control Set 2
3: Activate
Control Set 3
4: Activate
Control Set 4
5: Activate
Control Set 5
(Fastest)
6: Activate
Control Set 6
(Double Acting - Slow)
7: Activate
Control Set 7
(Double Acting- Fast)
0. Linear (most
common)
1. Equal
Percentage (30:1)
2. Equal
Percentage
(50:1)
3. Quick Open (reversal
from Equal Percentage
(50:1))
4. Custom 5. Camex™
Percentage
PV_SCALE.UNIT INDEX
= %
XD_SCALE.UNIT
INDEX = %
CHANNEL =
Position
SHED_OPT =
NORMAL SHED
NORMAL RETURN

20 | © 2021 Baker Hughes Company. All rights reserved.
Step 4: Run Find Stops METHOD
Use a conguration tool (DD, SVI FF local pushbuttons or software) to run METHOD.
Step 5: Run Auto Tune METHOD
Use a conguration tool (DD, SVI FF local pushbuttons or software) to run METHOD.
Downloads
To download the complete user manual, DD, SVI FF Advanced DTM and the ValVue Suite trial
program, visit:
https://valves.bakerhughes.com/resource-center.