Balt 27530 User manual

1
#27530 Adj Ht LCD TV Cart
with 2 Pull-out Shelves & Locking Cabinet
Assembly Instructions

2
P1 BaseCabinet 1 EA
P2 TopShelf 1 EA
P3 Pull-outShelf 2 EA
P4 Left Support Tubes 1 EA
P5 Right Support Tubes 1 EA
P6 LCD Bracket 2 EA
P7 Verticle Adj Straps 2 EA
P8 Cord Winder 1 EA
P9 Electrical Outlet 1 EA
Part Drawing Description Qty Part Drawing Description Qty
#27530 Adjustable Ht LCD Cart
We recommend that you assemble this
unit on a table.
Toolsrequired: AdjustableCrescentWrench
Hardware List
AScrew M6X12mm Pan Hd 8 EA
A1 ScrewM3.5X12mmCS 16 EA
A2 Screw M5X45mm Pan Hd 2 EA
A3 Screw M8X25mm Pan Hd 4 EA
A4 Screw M8X20mm SocketHd 2 EA
A5 Screw M6X20mm Pan Hd 4 EA
BHex nut M6 8 EA
B1 Hex nut M3.5 16 EA
B2 Hex nut M5 w/Flange 2 EA
B3 Hex nut M8 4 EA
CLock Washer Ext Tooth 8 EA
C1 Flat Washer 2 EA
D4” Locking Caster 2 EA
E4” Caster 2 EA
(For M6 Screw)
Do not use unless all screws are tight. At least every six months, check all screws to be sure
they are tight. If parts are missing, broken, damaged, or worn, stop use of the product
until repairs are made by your dealer using factory authorized parts.

3
#27530 Adjustable Ht LCD Cart
Assembly Diagram
IdentifyandSeparateallthePartsandHardware.
Illustration # 1
1.)
2.)
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT .
SlideTopShelf(P-2) over the
Base Cabinet (P-1) and secure at
desiredheightusing 8 screws (A),
8ExternalToothLockWashers
(C),and8HexNuts(B).
A
P-2
A
C
A
B
P1
Illustration # 2
Press 2 Locking Casters (D) and 2
non-lockingcasters(E)intothefactory
installednyloninsertsintheBase
Cabinet(P-1)asshownin illustration #2.
E
D
P1
D
E
3.)

4
AttachCord Winder (P-8) and Electrical
Strip (P-9) toTop Shelf (P-2), or Base
Cabinet (P-1) using 2 screws (A2) and 2
HexNutsM5w/Flange (B2).
Tightenallscrewsusing
Phillip’sheadscrewdriver and
Wrench(NotProvided).
Attach LeftandRight SupportTubes (P-4 &P-5)
toTop Shelf (P-2) using 2 screws (A4) and 2
Washers (C1) as shown in illustration #3.
Attach 2 LCD Brackets
(P-6)to Left and Right
SupportTubes(P-4 & P-5)
at desired height using 4
screws(A5)as shown in
illustration#4.
Attach 2 VerticleAdj
Straps (P-7) to the 2 LCD
Brackets (P-6) at desired
widthusing4 screws (A3)
and4Hex Nuts (B3) as
showninillustration#4.
Illustration # 4
Illustration # 3
Theproductyouhavepurchasedisguaranteedagainst material and workmanship defects. Thisguarantee
extends1yearfromdate of purchase. Should thisproductfailtofunctionsatisfactorilyundernormaluse due to
defectorimperfection, the defective partorproductwillbe replaced. Damage causedbycommoncarriersduring
shipmentisnotincludedinthisguarantee.
This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or
impliedshallapply. Failuretofollowinstructions foundinImportantInformation SectionofOwnerSheet
shallvoid theguarantee. Consequential orincidental damagesand orcosts arenot refundable.
Important
C1
A2
P-9
P-2
A2
P-8
P-4
P-5
A4
B2
B3
P-2
A3
P-7
A5
B3
A5
A3
P-7
P-6
P-6
P-4
P-5
4.)
5.)
6.)
7.)
8.)

5
Tilt 1PulloutShelf(P-3)and slide in from the
RightSideof cart. AttachPulloutShelf(P-3)to
Top Shelf (P-2) atdesiredheight using 8
screws(A1)and8 Hex Nuts (B1) asshownin
illustration # 5 & 5A.
9.)
LoosenHexnuts
beforeattachingPull
OutShelf.
A1
P-2
P-3
B1
Tilt 1 Pullout Shelf (P-3) and slide in from
theLeftSideofcart. AttachPulloutShelf
(P-3)toTopShelf (P-2) atdesired height
using8screws (A1) and 8HexNuts (B1)
asshowninillustration#6.
P-2
P-3
10.)
Detail 5A
P-3
P-2
Illustration # 6
Illustration # 5