Banner EZ-LIGHT K70 Series User manual

Datasheet
The Sure Cross®K70 Wireless Indicator Light combines the best of Banner's popular Indicator Light family with its reliable, field-
proven, Sure Cross wireless architecture.
• Available in 900 MHz and 2.4 GHz ISM Bands
• Up to five colors in one device
• Rugged, water-resistant IP65 housing with UV-stabilized material
• Bright, uniform indicator segments appear gray when off to eliminate false indication
from ambient light
• Two-way communication - lights can be controlled with the input wires or the master
radio
• Input wires can be configured as auxiliary sourcing inputs from external devices or as
a 20 Hz, 32-bit event counter
Important: Please download the complete K70 Wireless Indicator Light technical documentation, available in
multiple languages, from www.bannerengineering.com for details on the proper use, applications, Warnings,
and installation instructions of this device.
Important: Por favor descargue desde www.bannerengineering.com toda la documentación técnica de los K70
Wireless Indicator Light, disponibles en múltiples idiomas, para detalles del uso adecuado, aplicaciones,
advertencias, y las instrucciones de instalación de estos dispositivos.
Important: Veuillez télécharger la documentation technique complète des K70 Wireless Indicator Light sur notre
site www.bannerengineering.com pour les détails sur leur utilisation correcte, les applications, les notes de
sécurité et les instructions de montage.
Models
900 MHz Models
Model No. of Colors Colors Connection
K70DXN9RQ 1 Red
Integral 5-pin M12/Euro-style male quick
disconnect
K70DXN9GRQ 2 Green, Red
K70DXN9GYRQ 3 Green, Yellow, Red
K70DXN9BGYRQ 4 Blue, Green, Yellow, Red Integral 8-pin M12/Euro-style male quick
disconnect
K70DXN9WBGYRQ 5 White, Blue, Green, Yellow, Red
2.4 GHz Models
Model No. of Colors Colors Connection
K70DXN2RQ 1 Red
Integral 5-pin M12/Euro-style male quick
disconnect
K70DXN2GRQ 2 Green, Red
K70DXN2GYRQ 3 Green, Yellow, Red
K70DXN2BGYRQ 4 Blue, Green, Yellow, Red Integral 8-pin M12/Euro-style male quick
disconnect
K70DXN2WBGYRQ 5 White, Blue, Green, Yellow, Red
Integral quick disconnect models are listed; a mating corset is required (see Accessories on p. 8).
• To order the 150mm (5.9 in) PVC pigtail with quick disconnect model, replace the Q with QP in the model number, for
example K70DXN9RQP.
• To order the 2 m (6.5 ft) cable models, omit the suffix Q in the model number, for example K70DXN9R.
EZ-LIGHT®K70 Wireless Indicator Light
Original Document
192534 Rev. D
8 November 2019
192534

Installation Instructions
Assembling the K70
Align notches on
dome and base and
press together
Rotate the dome
clockwise to
lock into place
(notches shown in
locked position).
Wiring
Sourcing (PNP) Input Euro-style Male Pinouts Key
Module
C2
C3
C1
3
4
1
2
5
12–30 V dc
1
4
5
3
2
1 = brown
2 = white
3 = blue
4 = black
5 = gray
C1 = Module 1
C2 = Module 2
C3 = Module 3
EZ-LIGHT®K70 Wireless Indicator Light
2 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 192534 Rev. D

Sourcing (PNP) Input Euro-style Male Pinouts Key
7
6
2
1
5
4
8
3
12–30 V dc
Module
C1
C2
C3
C4
C5
C6
5
6
7
1
8
2
3
4
1 = white
2 = brown
3 = green
4 = yellow
5 = gray
6 = pink
7 = blue
8 = red (event counter input, if
enabled)
C1 = Module 1
C2 = Module 2
C3 = Module 3
C4 = Module 4
C5 = Module 5
C6 = Module 6
Input wires C1 through C6 can be used to either control the light segments or can be configured as external PNP Inputs. Refer to
the DIP switch settings for configuration instructions.
Configuration Instructions
Set the Radio Module DIP Switches
Before applying power to the device, set the radio module's DIP switches.
Default configurations are noted with (*).
DIP Switches
Binding
Push Button
LED
DIP Switch 1: Radio Transmit Power 900 MHz Models 2.4 GHz Models
OFF * 1 Watt (30 dBm) operation
Disabled
ON 250 mW (24 dBm) operation
The 900 MHz radios transmit at 1 Watt (30 dBm) or 250 mW (24 dBm). While the Performance radios operate in 1 Watt mode, they
cannot communicate with the older 150 mW radios. To communicate with 150 mW radios, operate this radio in 250 mW mode. For
2.4 GHz models, this DIP switch is disabled. The transmit power for 2.4 GHz is fixed at about 65 mW EIRP (18 dBm), making the
2.4 GHz Performance models automatically compatible with older 2.4 GHz models.
DIP Switch 2: Input Wires 900 MHz Models and 2.4 GHz Models
OFF * Input wires control lights
ON Disables wired input control of lights and converts wires to auxiliary Inputs
If there are no lights at the end of the input wires to turn on, the inputs still function as a sourcing input.
DIP Switch 3: Event Counter 900 MHz Models and 2.4 GHz Models
OFF * Default I/O operation
ON Configure input 5 as a 32-bit synchronous counter at a maximum frequency of 20 Hz; disable input 6 (the
counter requires two registers)
EZ-LIGHT®K70 Wireless Indicator Light
P/N 192534 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 3

The event counter is active for RF firmware revision 5.3 or higher. In the default position (OFF), the input 1 through 6 control the
tower lights. When DIP switch 3 is ON, input 5 wire is the counter input and input 6 wire is disabled. Registers 5 and 6 store the 32-
bit synchronous counter count. Inputs 5 and 6 are independent from the lights and will not drive any lights they are wired to. Input
wires 1 through 4 function normally.
DIP Switch 3: Event Counter 900 MHz Models and 2.4 GHz Models
OFF * Default I/O operation
ON
8-pin Models: Configure input 5 as a 32-bit synchronous counter at a maximum frequency of 20 Hz; disable
input 6 (the counter requires two registers)
5-Pin Models: Configure input 3 as a 32-bit synchronous counter at a maximum frequency of 20 Hz
The event counter is active for RF firmware revision 5.3 or higher.
For the 8-pin models: In the default position (OFF), inputs 1 through 6 control the tower lights. When DIP switch 3 is ON, input 5
wire is the counter input and input 6 wire is disabled. Registers 5 and 6 store the 32-bit synchronous counter count. Inputs 5 and 6
are independent from the lights and will not drive any lights they are wired to. Inputs 1 through 4 function normally.
For the 5-pin models: In the default position (OFF), inputs 1 through 3 control the tower lights. When DIP switch 3 is ON, input 3
wire is the counter input. Registers 3 and 4 store the 32-bit synchronous counter count. Input 3 is independent from the lights and
will not drive any lights they are wired to. Inputs 1 and 2 function normally.
DIP Switch 4: Bit Packing I/O 900 MHz Models and 2.4 GHz Models
OFF * Default I/O operation
ON Bit-packed I/O with all inputs in Modbus register 1 and all outputs in Modbus register 9. All other Modbus
registers are disabled.
Bit packing is active for RF firmware revision 5.8 or higher. Bit packing uses a single register, or range of contiguous registers, to
represent I/O values. This allows you to read or write multiple I/O values with a single Modbus message. Input 1 is stored in the
least significant bit of register 1. Output 1 is stored in the least significant bit of register 9.
Event Counter
To use the event counter, the measured (logic high) signal must be greater
than or equal to 25 ms. The 32-bit count is stored in I/O registers 5 and 6.
To zero out (clear) the event counter,
• Map an input/button on a Gateway to Node register 14 to clear the
counter when the input/button is activated; or
• From a host system, write a 1 (the output must transition from a zero
to a one to reset the counter) to Node register 14 or write a 5424
(0x1530) to Node control register 15.
RF firmware revision 5.3 or higher (on all products released after 3/20/2015) is
required to use this feature.
Correct
Incorrect
t = 0 25 ms 50 ms 75 ms 100 ms
Bind the K70 to the Gateway and Assign the Node Address
Before beginning the binding procedure, apply power to all the devices.
DIP Switches
Binding
Push Button
LED
EZ-LIGHT®K70 Wireless Indicator Light
4 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 192534 Rev. D

1. Enter binding mode on the Gateway.
• For housed models, triple-click button 2.
• For board-level modules, triple-click the button.
• For DXM models, under the ISM Radio menu, use the down arrow button to highlight the Binding menu. Click ENTER.
On the board modules, the green/red LED flashes. On the housed models, both LEDs flash red.
2. Assign the K70 a Node address using the Gateway's rotary dials or the DXM's arrow keys. Use the left rotary dial for the
left digit and the right rotary dial for the right digit. For example, to assign your K70 to Node 01, set the left dial to 0 and the
right dial to 1.
Valid Node addresses are 01 through 47.
3. Remove any components to access the circuit board in the radio module of the K70.
4. Enter binding mode on the K70 by triple-clicking the button.
The bicolor LED flashes alternately while it searches for a Gateway in binding mode. After the K70 is bound, the LED is red
and green for four seconds (looks amber), then it flashes four times (looks amber). The K70 automatically exits binding
mode, cycles power, and enters Run mode.
5. For DXM Gateways, click BACK to exit binding for that specific Node address.
6. Label the Node with the assigned address for future references.
This makes it easier to identify the physical Node location within a multi-Node network.
7. Reassemble the components back onto the base.
8. Repeat steps 2 through 5 for as many K70 Wireless Indicator Lights as are needed for your network.
9. After binding all K70s, exit binding mode on the Gateway.
• For housed models, double-click button 2.
• For board-level modules, double-click the button.
• For DXM models, click BACK until you return to the main menu.
LED Behavior for the Nodes
Nodes do not sample inputs until they are communicating with the Gateway. The radios and antennas must be a minimum distance
apart to function properly. Recommended minimum distances are:
900 MHz 150 mW and 250 mW radios: 6 feet
900 MHz 1 Watt radios: 15 feet
2.4 GHz 65 mW radios: 1 foot
LED (Bi-color) Node Status
Flashing green Radio link okay
Green and red flashing alternately In Binding mode
Both colors are solid for 4 seconds, then flash 4 times; looks amber Binding mode is complete
Flashing red, once every 3 seconds Radio link error
Flashing red, once every second Device error
Modes of Operation
Node Controlled. The wireless K70 Node can be operated similar to a wired model where the individual segments are activated by
a PLC or manual switch. In this scenario, the Gateway only monitors the status of the light segments. An example application
would be remotely monitoring the status of one or multiple machines from a single Gateway.
Gateway Controlled. In the Gateway-controlled mode, the K70 Node only requires 10 to 30 V dc power. Input signals sent from the
Gateway have full control over the status of all the segments. An example application would be a call-for-parts application with a
K70 Node mounted to a fork truck and the Gateway mounted in a work cell or stock room. When part pick-up or delivery is
needed, the operator sends a signal to the fork truck driver. A multicolor K70 could be used when there are multiple pick-up or
delivery locations.
EZ-LIGHT®K70 Wireless Indicator Light
P/N 192534 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 5

Sure Cross®User Configuration Software
The User Configuration Software offers an easy way to link I/O points in your wireless network, view I/O register values, and set
system communication parameters when a host system is not part of the wireless network. The software runs on any computer
with the Windows Vista, Windows 7, Windows 8, or Windows 10 operating system.
Use a USB to RS-485 adapter cable to connect a standalone DX80 Gateway to the
computer. For DXM Controllers with an internal DX80 radio, connect a computer to the
DXM Controller using a USB or Ethernet connection. Download the most recent revisions
of the configuration software from Banner Engineering's website:
www.bannerengineering.com/wireless.
The USB to RS-485 adapter cable is not required for the DXM Controller. For standalone
DX80 Gateway devices use:
• USB to RS-485 adapter cable model BWA-UCT-900 for 1 Watt radios
• USB to RS-485 adapter cable model BWA-HW-006 for all other radios
Creating Flash Patterns
Use the User Configuration Tool (UCT) to set the Duty Cycle, For Outputs of Node 1, output 9, to 0x0F0F as shown below, to
achieve this flash pattern.
Flash a K70 light by entering a time-based bit mask into the Duty Cycle parameter for that output register. Bit 0 represents the first
62.5 ms time window, bit 1 represents the second 62.5 ms window, etc.
For example, turn ON the output from 0 to 250 ms, OFF from 250 to 500 ms, ON from 500 to 750 ms, then OFF again from 750 ms
to 1 second by writing 0x0F0F to the appropriate output.
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Bin 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
Hex 0 F 0 F
Light Turned off from 750 ms to 1 s Turned on from 500 to 750 ms Turned off from 250 to 500 ms Turned on from 0 to 250 ms
This example shows 0F0F being written to the Duty Cycle, For Outputs parameter for Node 1, output 9.
Modbus Registers
I/O Modbus Holding Register I/O Type I/O Range Holding Register
Representation (Dec.)
Color #
Gateway Any Node Min. Max. Min. Max.
1 1 1 + (Node# × 16) Discrete IN 1 / Bit-packed inputs 0 1 0 1 C1
2 2 2 + (Node# × 16) Discrete IN 2 0 1 0 1 C2
3 3 3 + (Node# × 16) Discrete IN 3 0 1 0 1 C3
4 4 4 + (Node# × 16) Discrete IN 4 0 1 0 1 C4
5 5 5 + (Node# × 16) Discrete IN 5 / 32-bit event counter high word 0 1 0 1 C5
6 6 6 + (Node# × 16) Discrete IN 6 / 32-bit event counter low word 0 1 0 1 -
EZ-LIGHT®K70 Wireless Indicator Light
6 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 192534 Rev. D

I/O Modbus Holding Register I/O Type I/O Range Holding Register
Representation (Dec.)
Color #
Gateway Any Node Min. Max. Min. Max.
7 7 7 + (Node# × 16) Reserved
8 8 8 + (Node# × 16) Device Message
9 9 9 + (Node# × 16) Discrete OUT 9 / Bit-picked outputs 0 1 0 1 C1
10 10 10 + (Node# × 16) Discrete OUT 10 0 1 0 1 C2
11 11 11 + (Node# × 16) Discrete OUT 11 0 1 0 1 C3
12 12 12 + (Node# × 16) Discrete OUT 12 0 1 0 1 C4
13 13 13 + (Node# × 16) Discrete OUT 13 0 1 0 1 C5
14 14 14 + (Node# × 16) Discrete OUT 14 / Zero out (clear) the counter 0 1 0 1 -
15 15 15 + (Node# × 16) Control Message
16 16 16 + (Node# × 16) Reserved
Use the User Configuration Tool (UCT) software to define unique synchronous flash patterns for the lights.
Specifications
EZ-LIGHT K70
Supply Voltage and Current
12 to 30 V DC (Outside the USA: 12 V DC to 24 V DC, ± 10%) 1
Indicators - Maximum current per LED color:
Blue, Green, White: 200 mA at 12 V DC; 90 mA at 30 V DC
Red, Yellow: 150 mA at 12 V DC; 75 mA at 30 V DC
900 MHz Consumption: Maximum current draw is < 40 mA and typical
current draw is < 30 mA at 24 V DC. (2.4 GHz consumption is less.)
Supply Protection Circuitry
Protected against transient voltages
Indicator Response Time
Off Response: 150 µs (maximum) at 12 to 30 V DC
On Response: 180 ms (maximum) at 12 V DC; 50 ms (maximum) at 30 V DC
Construction
Base and cover: polycarbonate
Segment Lumens
Color Typical Wavelength or
Color Temp Typical Intensity (lm)
Green 525 nm 65
Red 625 nm 34
Yellow 590 nm 22
Blue 470 nm 22
White 5000 K 87
Indicators
1 to 5 colors depending on model: Green, Red, Yellow, Blue, and White
Connections
5-pin M12/Euro-style quick disconnect, 8-pin M12/Euro-style quick
disconnect, 150 mm (5.9 in) PVC cable with an M12/Euro-style quick
disconnect, or 2 m (6.5 ft) unterminated cable, depending on model
Operating Conditions
–40 °C to +50 °C (–40 °F to +122 °F)
95% at +50 °C maximum relative humidity (non-condensing)
Environmental Rating
IEC IP65
Vibration and Mechanical Shock
Vibration: 10 Hz to 55 Hz, 0.5 mm peak-to-peak amplitude per IEC
60068-2-6
Shock: 15G 11 ms duration, half sine wave per IEC 60068-2-27
Certifications
(CE approval only
applies to 2.4 GHz
models)
(NOM approval only
applies to 900 MHz
models)
Required Overcurrent Protection
WARNING: Electrical connections must be
made by qualified personnel in accordance with
local and national electrical codes and
regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via Current
Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Supply Wiring (AWG) Required Overcurrent Protection (Amps)
20 5.0
22 3.0
24 2.0
26 1.0
28 0.8
30 0.5
1For European applications, power this device from a Limited Power Source as defined in EN 60950-1.
EZ-LIGHT®K70 Wireless Indicator Light
P/N 192534 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 7

Radio
Radio Range
900 MHz, 1 Watt (Internal antenna): Up to 3.2 km (2 miles) with line of sight
2.4 GHz, 65 mW (Internal antenna): Up to 1000 m (3280 ft) with line of sight
Minimum Separation Distance
900 MHz, 1 Watt: 4.57 m (15 ft)
2.4 GHz, 65 mW: 0.3 m (1 ft)
Spread Spectrum Technology
FHSS (Frequency Hopping Spread Spectrum)
900 MHz Compliance (1 Watt)
FCC ID UE3RM1809: FCC Part 15, Subpart C, 15.247
IC: 7044A-RM1809
2.4 GHz Compliance
FCC ID UE300DX80-2400: FCC Part 15, Subpart C, 15.247
RED Directive 2014/53/EU
IC: 7044A-DX8024
Radiated Immunity HF
10 V/m (EN 61000-4-3)
Link Timeout
Gateway: Configurable via User Configuration Software
Node: Defined by Gateway
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise. Dimensions for the quick disconnect model are shown.
Accessories
Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model Length Style Dimensions Pinout (Female)
MQDC1-501.5 0.50 m (1.5 ft)
Straight
44 Typ.
ø 14.5
M12 x 1
2
3
4
1
5
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
MQDC1-506 1.83 m (6 ft)
MQDC1-515 4.57 m (15 ft)
MQDC1-530 9.14 m (30 ft)
MQDC1-506RA 1.83 m (6 ft)
Right-Angle
32 Typ.
[1.26"]
30 Typ.
[1.18"]
ø 14.5 [0.57"]
M12 x 1
MQDC1-515RA 4.57 m (15 ft)
MQDC1-530RA 9.14 m (30 ft)
EZ-LIGHT®K70 Wireless Indicator Light
8 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 192534 Rev. D

8-Pin Threaded M12/Euro-Style Cordsets with Open-Shield
Model Length Style Dimensions Pinout (Female)
MQDC2S-806 1.83 m (6 ft)
Straight
44 Typ.
ø 14.5
M12 x 1
5
4
3
2
8
1
7
6
1 = White
2 = Brown
3 = Green
4 = Yellow
5 = Gray
6 = Pink
7 = Blue
8 = Red
MQDC2S-815 4.57 m (15 ft)
MQDC2S-830 9.14 m (30 ft)
MQDC2S-850 15.2 m (50 ft)
MQDC2S-806RA 1.83 m (6 ft)
Right-Angle
32 Typ.
[1.26"]
30 Typ.
[1.18"]
ø 14.5 [0.57"]
M12 x 1
MQDC2S-815RA 4.57 m (15 ft)
MQDC2S-830RA 9.14 m (30 ft)
MQDC2S-850RA 15.2 m (50 ft)
All measurements are listed in millimeters, unless noted otherwise.
Mounting Brackets
SMB30A
• Right-angle bracket with curved
slot for versatile orientation
• Clearance for M6 (¼ in)
hardware
• Mounting hole for 30 mm sensor
• 12-ga. stainless steel
45
61
69
A
B
C
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
SMB30MM
• 12-ga. stainless steel bracket
with curved mounting slots for
versatile orientation
• Clearance for M6 (¼ in)
hardware
• Mounting hole for 30 mm sensor
70
57
A
B
C
57
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
SMBAMS30P
• Flat SMBAMS series bracket
• 30 mm hole for mounting
sensors
• Articulation slots for 90°+
rotation
• 12-ga. 300 series stainless steel
45
93 A
C
B
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
SSA-MBK-EEC1
• Single 30 mm hole
• 8 gauge steel, black finish
(powder coat)
• Front surface for customer
applied labels
80
85 60
45
B
A
Hole size: A = ø 7 , B = ø 30
LMBE12RA35
• Direct mounting of stand-off pipe, with
common bracket type
• Zinc-plated steel
• 1/2-14 NPSM nut
• Mounting distance from the wall to the
center of the 1/2-14 NPSM nut is 35 mm
Hole center spacing: 20.0
38.25
57
2X Ø9
1/2 - 14
NPSM NUT
55
35
LMBE12RA45
• Direct mounting of stand-off pipe, with
common bracket type
• Zinc-plated steel
• 1/2-14 NPSM nut
• Mounting distance from the wall to the
center of the 1/2-14 NPSM nut is 45 mm
Hole center spacing: 35.0
38.25
81
65
45
2X Ø11
1/2 - 14
NPSM NUT
All measurements are listed in millimeters, unless noted otherwise.
EZ-LIGHT®K70 Wireless Indicator Light
P/N 192534 Rev. D www.bannerengineering.com - Tel: + 1 888 373 6767 9

Elevated Mount System
Model Features Components
SA-M30 - Black Polycarbonate • Streamlined black PC or Gray PC thread cover
• Covers M30 thread on the light base
• Mounting hardware included
SA-M30C - Gray Polycarbonate
Polished 304 Stainless
Steel
Black Anodized
Aluminum
Clear Anodized
Aluminum
• Elevated-use stand-off pipe (½ in. NPSM/DN15)
• Polished 304 stainless steel, black anodized
aluminum, or clear anodized aluminum surface
• ½ in. NPT thread at both ends
• Compatible with most industrial environments
SOP-E12-150SS
150 mm (6 in) long
SOP-E12-150A
150 mm (6 in) long
SOP-E12-150AC
150 mm (6 in) long
SOP-E12-300SS
300 mm (12 in) long
SOP-E12-300A
300 mm (12 in) long
SOP-E12-300AC
300 mm (12 in) long
SOP-E12-900SS
900 mm (36 in) long
SOP-E12-900A
900 mm (36 in) long
SOP-E12-900AC
900 mm (36 in) long
SA-E12M30 - Black Acetal • Streamlined black acetal or white UHMW mounting
base adapter/cover
• Connects between ½ in. NPSM/DN15 pipe and 30
mm (1-3/16 in) drilled hole
• Mounting hardware included
SA-E12M30C - White UHMW
Pipe Mounting Flange
Model Features Construction
SA-F12
• Elevated-use stand-off pipes (½ in,
NPSM/DN15)
• M5 mounting hardware and nitrile gasket
included
Die-cast zinc base with
black paint
10
ø28
ø70
1/2-14
NPSM 4x ø5.5
54
Foldable Mounting Brackets
Model Features Construction
SA-FFB12
• For use with 1/2 inch stand-off pipes
• Stainless steel hardware
Black polycarbonate
111
110°
1/2-14 NPSM
4 x Ø5
Ø70
SA-FFB12C Gray polycarbonate
LMB Sealed Right-Angle Brackets
Model Description Construction
LMB30RA
Direct-Mount Models: Bracket kit with base, 30 mm
adapter, set screw, fasteners, O-rings, and gaskets.
Black polycarbonate
LMB30RAC Gray polycarbonate
LMBE12RA Pipe-Mount Models: Bracket kit with base, ½-14 pipe
adapter, set screw, fasteners, O-rings, and gaskets.
For use with stand-off pipe (listed and sold separately).
Black polycarbonate
LMBE12RAC Gray polycarbonate
EZ-LIGHT®K70 Wireless Indicator Light
10 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 192534 Rev. D