Barco R9841770 User manual

BARCO PROJECTION
LAMP KIT FOR IQPROJECTORS
R9841770 - R9841771
R9841100 - R9841111
R9841760 - R9841761
INSTALLATION MANUAL
05112002 R5976375/01

Barco nv Intelligent Displays
Noordlaan 5, 8520 Kuurne
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium

Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of BARCO.
Federal Communication Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.

Revision Sheet
To:
Barco nv Intelligent Displays
Noordlaan 5, 8520 Kuurne
Phone: [phone], Fax: [phone]
E-mail: [email protected], Web: www.barco.com
From:
Date:
Please correct the following points in this documentation (R5976375/01):
page wrong correct
R5976375 LAMP KIT FOR IQPROJECTORS 05112002

1. Safety
1. SAFETY
1.1 Safety Guidelines
This procedure is intended for use only by qualified service technicians who have been trained and authorized
by BARCO !
Hot Surface and Risk of Explosion:Switch the projector to stand by and let it cool down for at least 15 minutes
. These lamps consist of a quartz arc tube operating at very high temperature and high pressure (200 bar)
which may explode suddenly. There is a risk of personal injury and property damage from hot quartz arc tube
particles if handled incorrectly.
Risk of Electrical Shock: Power down the projector and unplug the power cord from the wall outlet. Once the
projector is cooled down and the power is off, continue with the replacement procedure.
Lamp Runtime Warning: Do not exceed the indicated maximum total lifetime of the lamp for safe operation in
normal power mode. Do not use it longer ! Always replace the lamp with the BARCO lamp kit for IQ projectors.
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 1

1. Safety
2R5976375 LAMP KIT FOR IQ PROJECTORS 05112002

2. Kit Content
2. KIT CONTENT
2.1 Contents
Overview
Depending on the Kitnumber ordered the kit may contain 1 or 2 lamps, the lamp power may also differ according to the type of iQ
Projector.
Kitnumber Description Quantity Manual
R9841771 120 W Lamp 1R5976375IQ200
R9841770 120 W Lamp 2R5976375
R9841111 200 W Lamp 1R5976375IQ300
R9841100 200 W Lamp 2R5976375
R9841761 250 W Lamp 1R5976375IQ400
R9841760 250 W Lamp 2R5976375
Image 2-1
Do not touch the cover glass with your fingers. If the lamp is touched, finger prints can be removed by cleaning
thelampwithalcohol.
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 3

2. Kit Content
4R5976375 LAMP KIT FOR IQ PROJECTORS 05112002

3. Reset runtime
3. RESET RUNTIME
3.1 Reset runtime
When to reset the lamp runtime ?
The lamp runtime should only be reset when placing a new lamp.
How to reset the lamp runtime ?
1. Press MENU to activate the Toolbar
2. Press →to select the Lamp item
3. Press ↓to Pull down the Lamp menu
4. Use ↑or ↓to select Reset runtime
5. Press →to pull down the menu
6. Use ↑or ↓to select the lamp to be reset (image 3-1)
7. Press ENTER
A dialogbox is displayed (image 3-2)
8. Use ←or →, the numeric keys on the remote, or the keypad to change the serial number of the lamp (serial number 0000000 will
not be accepted).
Image 3-1
Image 3-2
Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 5

3. Reset runtime
6R5976375 LAMP KIT FOR IQ PROJECTORS 05112002

4. Access to the lamp unit(s)
4. ACCESS TO THE LAMP UNIT(S)
4.1 Removing the back cover
Necessary tools
a flat screwdriver of 10 mm
Necessary parts
No parts.
Risk of Electrical Shock: For replacement procedures power down the projector and unplug the power cord
from the wall outlet. Once the projector is cooled down and the power is off, continue with the replacement
procedure.
Removingthebackcover
1. Turn with a screwdriver the cover lock screw A quarter turn counter clockwise. (image 4-1)
2. Remove the back cover.
See image 4-2, image 4-3
Image 4-1
rear cover lock screw Image 4-2
rear cover removed
Image 4-3
right view of the projector, rear cover removed
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 7

4. Access to the lamp unit(s)
8R5976375 LAMP KIT FOR IQ PROJECTORS 05112002

5. Removing the lamp unit(s)
5. REMOVING THE LAMP UNIT(S)
5.1 Removing the lamp unit(s)
What has to be done ?
1. The lamp power connection has to be disconnected.
2. The lamp unit has to be removed.
Perform the procedure for both lamps if necessary.
In this procedure lamp1 is replaced, the procedure being the same for lamp2.
Necessary tools
No tools.
Necessary parts
No parts.
How to remove the lamp unit ?
1. Disconnect the lamp (image 5-1)
See image 5-2.
2. Push the lamp locking handle slightly to the left (or to the right for lamp 2) and turn it over to unlock the lamp (image 5-3)
3. Take out the lamp unit (image 5-4)
See image 5-5.
Image 5-1
lamp connector
Image 5-2
disconnected lamp connector
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 9

5. Removing the lamp unit(s)
Image 5-3
unlocking lamp 1 & lamp 2
Image 5-4
Image 5-5
Lamp 1 removed
10 R5976375 LAMP KIT FOR IQ PROJECTORS 05112002

6. Mounting the Lamp Unit
6. MOUNTING THE LAMP UNIT
6.1 Mounting the lamp unit(s)
What has to be done ?
1. The lamp has to be mounted
2. The lamp has to be connected.
Perform the procedure for both lamps if both lamps have to be replaced.
In this procedure lamp1 is replaced, the procedure being the same for lamp2.
Necessary tools
No tools.
Necessary parts
No parts.
How to mount the lamp unit ?
1. Place carefully the lamp against the frame
2. Push the lamp inwards and turn the lamp locking handle over to lock the lamp (image 6-1)
3. Connect the lamp (image 6-2)
Image 6-1
locking lamp 1 & lamp 2
Image 6-2
lamp connected
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 11

6. Mounting the Lamp Unit
12 R5976375 LAMP KIT FOR IQ PROJECTORS 05112002

7. Mounting the cover.
7. MOUNTING THE COVER.
7.1 Mounting the cover.
Mounting the back cover
1. Replace the back cover.
2. Turn with a screwdriver the cover lock screw a quarter turn clockwise to lock the cover. (image 7-1)
Image 7-1
R5976375 LAMP KIT FOR IQ PROJECTORS 05112002 13

7. Mounting the cover.
14 R5976375 LAMP KIT FOR IQ PROJECTORS 05112002