Barska AX13500 User manual

User’s Manual for Key Safe
WARNING
Read all instructions before using this safe.
A. Handle
B. Key Access
C. Key Pad
D. Indicator Lights
E. Key Drop Slot
- Located on the side of the safe
- For security purposes, change the factory default
code as soon as possible. Factory default code
is 159 and 011223.
-Test registered pin code a few times before closing
the safe door.
- Avoid leaving door open and unattended; it will allow
unauthorized individuals to reprogram the safe,
gaining full access to the safe and its contents.
- Store emergency keys in a secure place; NOT inside
of the safe.
- To maximize security and performance of the safe,
L
o
c
k
U
n
l
o
c
k
See reverse side for more information
GETTING STARTED
Remove emergency keys and other included
accessories from packaging.
KEY ACCESS
1. Remove grey key cover located on the safe to expose
key hole.
2. Use emergency key and insert into key hole, turn key
counter clockwise and turn handle clockwise.
BATTERY
Battery compartment is located on the inside of the door
safe.
1. Remove battery compartment cover.
2. Insert four AA alkaline batteries into the battery
compartment and restore battery compartment cover.
Note: Do not mix new and old batteries
PIN CODE REGISTRATION
1st Safe Default Pin Code : 159
2nd Safe Default Pin Code : 011223
1. Press “* *”, then yellow indicator light next to warning
will light up.
2. Input current user code that you want to change, and
press “#”.
3. Input your new pin code you want to change it to and
press “#”.
4. Input your new pin code one more time to confirm
registration and press “#.” Yellow light will turn off,
meaning code has been registered.
Repeat steps above to change second pin code
TESTING REGISTERED PIN CODE
With safe door open turn handle counter clockwise to
extend the bolts. Enter registered pin code and press “#”
safe should unlock. Turn handle clockwise and bolts
shall retract; if safe unlocked then registration is
complete.
Note: If safe does not unlock then pin code registration
was unsuccessful. Please start over with Pin Code
Registration.
DELETING PIN CODES / RESETTING SAFE TO
FACTORY DEFAULT MODE
Please only reset the safe if Pin Codes are lost or
forgotten.
PARTS OF THE SAFE
A
B
E
C
D
1. Open safe and remove screws securing the back
cover to the safe.
2. You will see a small button located on the
circuit board.
3. Press and hold small button until you see all the
lights flash and 2 quick beeps will be heard.
4. All pin codes have been resetted to factory
Default Pin Codes.
Note: 1st Safe Default Pin Code : 159
2nd Safe Default Pin Code : 011223
MOUNTING INSTRUCTIONS
The safe may be mounted to a wall. Be aware of the
load bearing. Failure to do so can result in personal
injury and/or damage to property. Use appropriate
tools when performing work and always use eye
protection.
- Do not mount the safe without anchoring to the
wall.
- Find the studs in the wall, at your desired location.
Most studs are 16 inches or 24 inches apart.
- Check the wall for concealed wires or pipes.
- Measure the location of the pre-set drill holes; mark
their exact position onto the wall ensuring that the
studs or anything else behind will not interfere.
- Drill the appropriate size holes for the anchors you
are using.
- Carefully press the anchor into the holes at
this time.
- Mount the safe by running screws from inside of the
safe and securing to anchors; ensure the safe is
mounted securely.
2/20
BC636
© 2020 BARSKA®
855 Towne Center Drive | Pomona, CA 91767
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
test pin code every 6 months.
- Test and make sure the safe works properly before
mounting. Once tested, mount the safe before use.

CARE AND MAINTENANCE
- Keep liquids away from the control panel. Spills on the
control panel will cause damage and possibly
electric shock.
- Secure safe in a proper area to prevent from falling and
causing damage or injury.
- DO NOT disassemble the product. For all repairs,
contact BARSKA Customer Service.
- DO NOT use chemicals or cleaning agents to clean
the safe.
2/20
1 YEAR LIMITED WARRANTY
SAFE
BARSKA warrants this new safe to be free of original defects
in material and/or workmanship under normal use for a
period of twelve (12) months from the date product is
received by purchaser. This warranty does not include
damage caused by improper installation or maintenance.
Damage from misuse, abuse, accident (such as dropping),
normal wear and tear, fire, flood, or acts of nature. Damage
from service or repairs other than those performed by
BARSKA. Labor, cost and shipping charges for the removal
and replacement of defective parts beyond the initial
twelve-month warranty period. All transportation and shipping
charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products
purchased in the United States.
Please email [email protected] or call 1.888.666.6769 for
Return Merchandise Number (RMA#) before any returns. The
RMA number must appear on the outside of the shipping
package. Product must be packed carefully and sturdily in its
original packaging to prevent damage in transit and returned
freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order to cover inspection, shipping and
handling. Charges are as follows:
$90 – Large
$70 – Standard
$40 - Compact
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new
unit if necessary within the warranty period. Purchaser is
required to remit amount above to BARSKA for return shipping
and handling at time product is returned. If repair is required
after warranty period expiration, purchaser will be
charged for replacement parts and return shipping.
BARSKA® Optics shall not be liable for any consequential,
incidental and/or contingent damages whatsoever. We will
not pay shipping, insurance or transportation charges from
you to us, or any import fees, duties and or taxes. This
warranty supersedes all previous BARSKA® Optics
warranties.