Barska AX11224 User manual

User’s Manual for
Digital Keypad Biometric Safe
WARNING
- Safe can be opened by either Fingerprint, PIN code,
and/or Override Keys.
- When you start using the safe register both Fingerprint
and PIN code.
- Register at least two different fingerprints and test a few
times before closing the safe door.
- Avoid leaving safe door open and unattended; it will allow
unauthorized individuals to add their fingerprints and/or
reprogram the safe, gaining full access to the safe and
the contents.
- Test the Override Keys and store them in a secure
place, NOT inside of the safe.
- To maximize the security and performance of the safe,
test registered fingerprints every 6 months.
Read all instructions before using this safe.
A. LED Light
B. Battery Compartment
C. Bolts
D. Keypad
E. Fingerprint Scanner
PIN CODE REGISTRATION
You will be able to program one pin code. (Pin Code can be 3-6
digits, Default Pin code: 123456)
You will be able to change the pin code by repeating below
registration process.
Factory default pin code is 123456, please follow following
procedure to register new pin code. The old pin code will be
over-write after you register new pin code.
1. When door open and bolt is retracted, input “ CLEAR CLEAR
68 LOCK” on keypad, and you will see “NEU” on the screen.
2. Input new 3-6 digits pin code and press “LOCK”, the bolt will
be extended, you will see “CLOSEd” on the screen. Now your
pin code is registered.
TEST REGISTERED PIN CODE
1. With the safe door open, press “LOCK” to have the bolt
extended in lock position.
2. Input pin code on the keypad, the bolt will be retracted and
display shows “OPEN” and “OPENEd”.
UNLOCK THE SAFE
1. With Pin Code: press the pin code on the keypad, the bolt will
be retracted and display shows “OPEN” and “OPENEd”.
2. With Fingerprint: press your fingerprint on scanner to wake
up the scanner, and press registered fingerprint on scanner,
the bolt will be retracted and display shows “OPEN”,
“OPENEd”
When you enter the wrong code or wrong fingerprint, the
display will show “Error”
LOCK THE SAFE
The safe can be unlocked by Press “LOCK” or press any finger
on fingerprint scanner.
1. With the keypad: Please hold the door closed and press
“LOCK”. The bolt will be extended and safe is locked, the
display shows “CLOSE” and “CLOSEd”.
2. With the Fingerprint: Please hold the door closed and press
any finger on fingerprint scanner. The bolt will be extended
and safe is locked, the display shows “CLOSE” and
“CLOSEd”,
See reverse side for more information 6/20
BC642
F. Cover
G. USB Port
(Manufacture Use Only)
H. Override Key Access
Corner Guard
GETTING STARTED
1. Remove all accessories that come with safe.
2. Open safe door and remove the battery cover.
3. Insert 4 AA batteries, pay attention to the polarity of the
batteries and put the battery cover into place.
4. Remove the corner guard from the safe door.
See diagram
Note: Do not mix new and old batteries.
Do not use rechargeable batteries or any other
type of non-alkaline battery.
OVERRIDE KEY
To unlock the safe using override key, remove the override key
cover, insert the keys and turn counter clockwise to retract the
bolt. The safe will be unlocked.
Test the override keys and store the keys properly. Please
note do not store the override key inside the safe.
FINGERPRINT REGISTRATION
You will be able to program 20 fingerprints.
1. When door open and bolt is retracted, press “ CLEAR
CLEAR “ on keypad and you will see “PrOG” on the screen,
press “LOCK” on keypad. The fingerprint scanner will light up
to start fingerprint registration process.
2. Put your fingerprint on scanner firmly and you will hear beep
then you can release, repeat 3 times, you will see “dONE” on
the display and follow by the number. Now your fingerprint is
registered. The number is showing how many fingerprints are
registered. If the display show “Error”, the registration is not
success, please repeat the registration process.
Safe can program up to 20 fingerprints. The screen will show
“Full” when there are 20 registered fingerprints.
TEST REGISTERED FINGERPRINT
1. With the safe door open, press “LOCK” to have the bolt
extended in lock position.
2. Press your fingerprint on scanner to wake up the scanner,
and press registered fingerprint on scanner, the bolt will be
retracted and display shows “OPEN”, “OPENEd”
DELETE REGISTERED FINGERPRINTS
When safe unlock, input “CLEAR CLEAR 763 LOCK” on
keypad. ALL the registered fingerprints are deleted.
Remove cover
to expose
AB
G
H
C
D E
F
F

SOUND OPTION
When the safe is open and bolt is retracted,
Sound Off
Press “ CLEAR CLEAR 0530 LOCK”, the display shows
“dONE”, now the Sound is off
Sound On
Press “ CLEAR CLEAR 0531 LOCK”, the display shows
“dONE”, now the Sound is on
LOCK OUT MODE
If the wrong pin code is entered 4 times safe will enter lock out
mode.
User will need to wait 15 min to use safe again; or user can
open safe with override key.
LOW BATTERY WARNING
With safe locked you can push on keypad and press “LOCK”
key; it will show BA-LO.
Means safe battery is low and should be changed as soon as
possible.
CARE AND MAINTENANCE
- To maximize the security and performance of the safe, keep
Fingerprint Scanner clean; use a dry cloth to remove any
smudges or prints off the Fingerprint Scanner after each use
- Test registered fingerprints and PIN code every 6 months
- Keep liquids away from the control panel. Spills on the control
panel will cause damage and possibly electric shock
- Secure safe in a proper area to prevent from falling and
causing damage or injury
- DO NOT disassemble the product. For all repairs, contact
BARSKA Customer Service
- DO NOT use chemicals or cleaning agents to clean the safe
MOUNTING INSTRUCTIONS
The safe may be mounted to a wall or floor. Be aware of the
load bearing. Failure to do so can result in personal injury
and/or damage to property. Use appropriate tools when
performing work and always use eye protection
Wall Mounting
Do not mount the safe without anchoring to the wall
- Find the studs in the wall, at your desired location. Most studs
are 16 inches or 24 inches apart
- Check the wall for concealed wires or pipes
- Measure the location of the pre-set drill holes; mark their exact
position onto the wall ensuring that the studs or anything else
behind will not interfere
- Drill the appropriate size holes for the anchors you are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely
Floor Mounting
- Use proper drill tools depending on the type of floor you are
mounting the safe (wood, tile, or concrete)
- Measure the location of the pre-set drill holes; mark their exact
position onto the floor
- Drill the appropriate size holes for the anchors you are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely
Safe
BC323
BARSKA warrants this new safe to be free of original defects
in material and/or workmanship under normal use for a
period of twelve (12) months from the date product is
received by purchaser. This warranty does not include
damage caused by improper installation or maintenance.
Damage from misuse, abuse, accident (such as dropping),
normal wear and tear, fire, flood, or acts of nature. Damage
from service or repairs other than those performed by
BARSKA. Labor, cost and shipping charges for the removal
and replacement of defective parts beyond the initial
twelve-month warranty period. All transportation and shipping
charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products
purchased in the United States.
Please email [email protected] or call 1.888.666.6769 for
Return Merchandise Number (RMA#) before any returns. The
RMA number must appear on the outside of the shipping
package. Product must be packed carefully and sturdily in its
original packaging to prevent damage in transit and returned
freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $40.00 to cover inspection,
shipping and handling.
*Please allow 6-8 weeks for delivery.
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new
unit if necessary within the warranty period. Purchaser is
required to remit $40.00 to BARSKA for return shipping and
handling at time product is returned. If repair is required after
warranty period expiration, purchaser will be
charged for replacement parts and return shipping.
BARSKA® Optics shall not be liable for any consequential,
incidental and/or contingent damages whatsoever. We will
not pay shipping, insurance or transportation charges from
you to us, or any import fees, duties and or taxes. This
warranty supersedes all previous BARSKA® Optics
warranties.
1 YEAR LIMITED WARRANTY