Barska DX Series User manual

User’s Manual for
Depository Safe DX Series
WARNING
- For security purposes, change the factory default
code as soon as possible. Factory default
code is: 168#
- Test registered pin code a few times before closing
the door.
- Avoid leaving the safe door open and unattended; it
will allow unauthorized individuals to reprogram the
safe gaining full access to the safe and its contents.
- Store emergency keys in a secure place; NOT inside
of the safe.
- Be careful when opening and closing the
depository slot.
- Keep children away from safe; they should not play
with or around the safe at anytime.
- Note: Barska is not responsible for any installation
damages and any lost or stolen contents.
Read all instructions before using this safe.
A. Handle
B. Indicator Lights
C. Key Pad
D. Battery Compartment
(Located behind key pad)
BATTERY & KEY ACCESS
Push down on button
located under the key pad
and turn keypad cover
counter clockwise.
DO NOT pull on the wires or
touch the electronic
components.
Install Battery
Insert one new 9V alkaline battery into the battery
compartment and restore keypad cover.
Key Access
Insert access key into key slot and turn clockwise to
open safe.
PIN CODE REGISTRATION
Safe retains 2 pin codes
Safe Default Pin Code: “168”
Changing First Pin Code
1. Open Safe with either Pin Code or Emergency Key.
2. Press initialization button located inside of the safe,
lock will beep wtice and yellow indicator light will be lit.
3. Enter desired Pin Code (1-8 Digits) then press
“ *” button. 2 short beeps will be heard and yellow
indicator light will disappear.
4. Use the handle to extend the safe bolts and enter
registered pin code then press “ # ” button.
If safe can be opened registration was successful, if safe
doesn’t open registration was unsuccessful, please
follow steps in Pin Code Registration to register
Pin Code.
Changing Second Pin Code
1. Open Safe with either Pin Code or Emergency Key.
2. Press “ 00 ” on the keypad, then press the initialization
button located on the inside of the safe, lock will beep
twice and yellow indicator light will be lit.
3. Enter second desired Pin Code (1-8 Digits) then press
“ *” button. 2 short beeps will be heard and yellow
indicator light will disappear.
4. Use the handle to extend the safe bolts and enter
registered pin code then press “ # ” button.
If safe can be opened registration was successful, if safe
doesn’t open registration was unsuccessful, please
follow steps in Pin Code Registration to register
Pin Code.
See reverse side for more information
10/17
BC555
PARTS OF THE SAFE
© 2017 BARSKA®| Pomona, CA 91767, USA
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
D. Emergency Key Access
(Located behind key pad)
F. Initialization Button
Actual model may vary
Inside of Safe Door
A
C
DE
B
F

OPENING AND CLOSING SAFE WITH PIN CODE
Safe can only be opened with emergency keys.
Open
1. On the key pad enter in either of the registered Pin
Codes and press and release “ # ” to confirm.
2. Turn the handle to the unlocked position and pull safe
door open.
Close
Close the safe door and turn the handle to the locked
position.
DUAL PIN CODE ACCESS
This feature will require entering both Pin Codes to
access the safe.
Enabling Dual Pin Code Access
Enter “*# 00 # ” followed by Pin Code & “ # ” button.
Disable Dual Pin Code Access
To disable Dual Pin Code Access enter “* # 11 # ”
followed by Pin Code 1 & “ # ” button, then enter Pin
Code 2 & “ # ” button.
LOCK OUT MODE
- If wrong code is entered 3 times safe will be in lock
out mode.
Lock Out Mode: Cannot use any functions on the safe
for 15 min, please leave batteries plugged into safe and
wait 15 min for insert key to unlock safe.
LOW BATTERY WARNING
If red indicator light is constantly lit while accessing and
using the safe, this indicates that the batteries are low,
please replace battery as soon as possible.
Note: Safe may still be opened in low battery state
depending on the voltage. If safe cannot be opened
please use emergency key. All registered Pin Codes
remains saved.
CARE AND MAINTENANCE
- Keep liquids away from the control panel. Spills on the
control panel will cause damage and possibly
electric shock.
- Secure safe in a proper area to prevent from falling and
causing damage or injury.
- DO NOT disassemble the product. For all repairs,
contact BARSKA Customer Service.
- DO NOT use chemicals or cleaning agents to clean
the safe.
MOUNTING INSTRUCTIONS
The safe may be mounted down to the floor. Be aware of
the load bearing. Failure to do so can result in personal
injury and/or damage to property. Use appropriate tools
when performing work and always use eye protection.
Floor Mounting
- Use proper drill tools depending on the type of floor you
are mounting the safe (wood, tile, or concrete).
- Measure the location of the pre-set drill holes; mark
their exact position onto the floor.
- Drill the appropriate size holes for the anchors you
are using.
- Carefully press the anchor into the holes at this time.
- Mount the safe by running screws from inside of the
safe and securing to anchors; ensure the safe is
mounted securely.
Safe
BC283 10/17
BARSKA warrants this new safe to be free of original defects
in material and/or workmanship under normal use for a
period of twelve (12) months from the date product is
received by purchaser. This warranty does not include
damage caused by improper installation or maintenance.
Damage from misuse, abuse, accident (such as dropping),
normal wear and tear, fire, flood, or acts of nature. Damage
from service or repairs other than those performed by
BARSKA. Labor, cost and shipping charges for the removal
and replacement of defective parts beyond the initial
twelve-month warranty period. All transportation and shipping
charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products
purchased in the United States.
Please email [email protected] or call 1.888.666.6769 for
Return Merchandise Number (RMA#) before any returns. The
RMA number must appear on the outside of the shipping
package. Product must be packed carefully and sturdily in its
original packaging to prevent damage in transit and returned
freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $60.00 to cover inspection,
shipping and handling.
*Please allow 6-8 weeks for delivery.
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new
unit if necessary within the warranty period. Purchaser is
required to remit $60.00 to BARSKA for return shipping and
handling at time product is returned. If repair is required after
warranty period expiration, purchaser will be
charged for replacement parts and return shipping.
BARSKA® Optics shall not be liable for any consequential,
incidental and/or contingent damages whatsoever. We will
not pay shipping, insurance or transportation charges from
you to us, or any import fees, duties and or taxes. This
warranty supersedes all previous BARSKA® Optics
warranties.
1 YEAR LIMITED WARRANTY