Baumatic BAF90EG User manual

USER MANUAL
BAF90EG
900MM UPRIGHT COOKER

2 Baumatic BAF90EG 900mm Upright Oven User Manual

Baumatic BAF90EG 900mm Upright Oven User Manual 3
Dear Customer,
Congratulations on purchasing your new product from Home Appliances.
To register your Parts and Labour Warranty, some conditions apply, please refer to your warranty card for more details
and contact our Customer Care team on:
1800 444 357
Our Customer Care Centre is there to ensure you get the most out of your appliance. Should you want to learn more
about your product and how to use it to its best potential or tips on cleaning, please feel free to call us on the above
number.
It is important that you read through the following instruction manual thoroughly to become familiar with the installation
and operation of this appliance and ensure optimum performance.
We also carry a complete range of spare parts for all Home Appliance products. For all your spare parts enquiries
please contact our team at Pronto Parts on
1300 306 973
Again, thank you for choosing an appliance brought to you by Home Appliances and we look forward to being of
service to you.
Kind regards,
The Management
Home Appliances

4 Baumatic BAF90EG 900mm Upright Oven User Manual
Contents
NOTE: READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE
It is important that you retain these instructions, proof of purchase as well as other important documents about
this product for future reference.The manufacturer will not be responsible for any damage to property or to
persons caused by incorrect installation or improper use of the appliance.
Due to continual product development, Baumatic reserves the right to alter specifications and appearances
without notice. THIS APPLIANCE HAS BEEN DESIGNED FOR DOMESTIC USE ONLY TO BE INSTALLED
BY AN AUTHORISED PERSON
DO NOT OPERATE THIS APPLIANCE BEFORE READING THE INSTRUCTION BOOK
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE
DO NOT STORE CHEMICALS OR FLAMMABLE MATERIALS OR SPRAY AEROSOLS NEAR THIS
Warnings.......................................................................................................................................5
Local authority requirements ................................................................................................ 6 - 7
Important information for installing the appliance...................................................................8
Appliance gas connection ........................................................................................................9
Support legs ...............................................................................................................................10
Anti-til device ..............................................................................................................................11
Convertion to a different type of gas .......................................................................................12
Appliance electric connection ................................................................................................13
Appliance use and maintenance...................................................................................14 - 16
Using Oven Functions................................................................................................................17
Cooking Functions ............................................................................................................18 - 21
Clock Functions .................................................................................................................24 - 25
Key Functions .....................................................................................................................22 - 23
Other Functions .................................................................................................................24 - 25
Troublshooting............................................................................................................................26
Disposal information..................................................................................................................27

Baumatic BAF90EG 900mm Upright Oven User Manual 5
Warnings:
Warnings:
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervised or instruction
concerning use of the appliance by a responsible person for their safely.
• Young children should be supervised to ensure that they do not play with the appliance.
• During use the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven.
• WARNING: Ensure the appliance is switched off before replacing the lamp to avoid the possibility of electric
shock.
• WARNING - Accessible parts will become hot when in use. To avoid burns young children should be kept away.
• This appliance is not intended to be operated by means of external timer or separate remote control system
• Do not use a steam cleaner to clean this appliance
• Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven glass door since they can scratch
the surface, which may result in shattering of the glass
• If this appliance is installed on a base, measures must be taken to prevent the appliance from slipping from the
base
• If the electrical supply is restricted, means of all-pole disconnection must be accessible and incorporated in the
fixed wiring in accordance with the wiring rules. If instructions for grilling mention to keep the door open:
• WARNING: Accessible parts may become hot when the grill is in use. Children should be kept away.
• NOTE 1: If the range is not fitted with a flexible cord, the instruction manual must clearly state the type and size of
cord to be used. In this case HO5VV-F 3G1.5mm² would be appropriate
• NOTE 2: The instruction manual must include details indicating the correct installation and use of the baking tray
and shelves. If this appliance is sold in New Zealand and not provided with a supply cord or an installed male
connector, the Instruction Manual shall state the size of cord to be used and shall include the substance of the
following:
• If this cooking range is to be connected to a new or upgraded electrical installation, then it must be connected by a
supply cord fitted with:
• An appropriate rated plug that is compatible with the socket-outlet fitted to the final sub-circuit in the fixed wiring
that supplies this cooker
• An appropriate rated installation male connector that is compatible with the installation female connector fitted to
the final sub-circuit in the fixed wiring that supplies the cooker

6 Baumatic BAF90EG 900mm Upright Oven User Manual
Local Authority Requirements
Local Authority Requirements
• Before installation, unpack all parts from carton, remove all internal packaging and check for damage. Check Gas Type
and specifications plate placed on the rear of the unit, alternatively there is a second label supplied. All gas fitting work,
service and repairs can only be performed by an authorised person in accordance with AS/NZS 5601 and local gas
regulations. Failure to comply with this condition will void the warranty. Always unplug the appliance before carrying out
any maintenance operations or repairs. The walls of the units must not be higher than worktop and must be capable
of resisting temperatures of 65°C K ( 65°C Above Amb.Temp. ) or higher. Do not install the appliance near flammable
materials (eg. curtains). The final act of any installation or gas type conversion must be the full testing of this appliance,
which includes leak testing, ignition of each burner and the functionality of the burners separately and together.
Keep all the dangerous packing parts (polystyrene foam, bags, cardboard, staples, etc.) away from children.
• Any walls of the adjacent furniture pieces and the wall behind the cooker must be made of heat-resistant material
that can withstand a minimum temperature of 65° K ( 65°C Above Amb.Temp.
Clearance above and around domestic cookers:
Requirements
1. Overhead clearances – (Measurement A)
Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However,
in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood
or an overhead exaust fan be less than 700 mm.
Any other downward facing combustible surface less than 700 mm above the highest part of the hob shall be
protected for the full width and depth of the cooking surface area in accordance with clause 5.12.1.2.
However, in no case shall the clearance to any surface be less than 450mm.
The maximum depth of wall cabinet above the cooking shall be 400 mm.

Baumatic BAF90EG 900mm Upright Oven User Manual 7
Local Authority Requirements
2. Side clearances – (Measurements B & C)
Where B, measured from the periphery of the nearest burner to any vertical combustible surface, is less than
200mm, the surface shall be protected in accordance with Clause 5.12.1.2 to a height C of not less than
150mm above the hob for the full dimension (width or depth) of the cooking surface area. Where the cooking
appliance is fitted with a “splash back”, protection of the rear wall is not required. The appliance can be installed
between two walls. A single sidewall that exceeds the height of the work surface is possible. This must be at a
minimum distance of 70 mm from the edge of the cooker.
3. Additional requirements for Freestanding and Elevated Cooking Appliances –
(Measurements D & E)
Where D, the distance from the periphery of the nearest burner to a horizontal combustible surface is less than
200 mm, then E shall be 10 mm or more, or the horizontal surface shall be above the trivet. See inserts above.
Important information for Installing the Appliance
• The cooker can be installed separately, as a freestanding unit, or between kitchen units or between a kitchen unit
and the wall. This appliance is not connected to devices which exhaust combustion products. Special attention
must be focused on the prescriptions described below regarding room aeration and ventilation. The dimensions of
the appliance are listed below:
Room Ventilation
• To ensure that the appliance operates correctly, the room where it is installed must be continuously ventilated. The
room volume should not be less than 25m3 and the quantity of air should be based on the regular combustion of
gas and on the ventilation of the room. Natural air will flow through permanent openings in the walls of the room to
be ventilated. These openings will be connected with the outside environment and should have a minimum cross
section defined by current national standards regarding room ventilation (Fig. 02).
These openings should be built so that they cannot be clogged.
Indirect ventilation is also permitted by taking air from the rooms adjacent to the one to be ventilated.

8 Baumatic BAF90EG 900mm Upright Oven User Manual
Important Information for Installing the
Appliance
Appliance Gas Connection:
• IMPORTANT: This appliance must be installed by an authorised person.
• WARNING: DO NOT MODIFY THIS APPLIANCE
• If the appliance cannot be adjusted to perform correctly, contact the service department.
• This appliance utilises a threaded 1/2" gas male fitting.
• To connect the appliance to the gas network with a flexible hose, a supplemental hose nipple fitting is needed
which is supplied with the appliance. (Fig. 05)
Location and Aeration
• Gas cooking appliances must always evacuate the combustion products by means of hoods connected to
chimneys, flues or directly outside (Fig. 03). If a hood cannot be installed It is possible to use a fan installed on a
window or directly facing outdoors, to be operated together with the appliance ( Fig. 04), provided that there is
strict compliance with the ventilation regulations. Disposing of old appliances
Gas inlet positions with different leg heights – mm
Gas inlet (mm) - Nat gas Gas inlet (mm) - LPG
From RH rear side: 35 mm From RH rear side: 35mm
Up from floor: 560 - 595mm (590mm nominal) Up from floor: 645 – 680mm (675 mm nominal)

Baumatic BAF90EG 900mm Upright Oven User Manual 9
Appliance Gas Connection
Gas Regulator
• The gas connection is via 1/2" tapered thread. Connect the cooker to the gas supply and test for leaks. NEVER
use a naked flame to check for gas leaks.
• Natural Gas: Gas regulator supplied with the appliance must be installed. LPG: Test point adaptor to be fitted and
checked at time of installation.
Using a flexible connection
• This appliance is approved for connection with a flexible hose, which complies with the AS/NZS 1869 (AGA
Approved), 10mm ID, class B or D, between 1-1.2m long. Connection shall be in compliance with AS5601.
When installing the hose restraint device, the appliance anchor point is the rear panel.
Using a Copper Pipe connection
• The cooker must be connected to the gas supply with upstream connection of an isolation valve in accordance
with the respectively valid regulations. We recommend that the isolation valve be fitted prior to the cooker to enable
isolation of the cooker from the gas supply. The valve must be easily accessible at all times.
To find out the gas type factory settings, see label on the rear of the appliance.
Test the operation of the cooker before leaving
• Note: These burners have no aeration adjustment.
• Check correct operation of the ignitions system and operation of the regulator and operation of the burners
individually and in combination. Burner flames should be clear blue, with no yellow tipping. If the burners show any
abnormality check that the burners are correctly located. If satisfactory performance cannot be obtained, contact
Baumatic service.
1.02
1.02

10 Baumatic BAF90EG 900mm Upright Oven User Manual
Support Legs
• The cookers are supplied with four transit supports (one for each corner).
• Four support legs are supplied separately and are fitted on location to the four corners of the lower support frame.
Each support leg is pushed over the relevant transit support until flush with the support frame.
• Each leg is adjusted by screwing the lowe r section in or out as required for fitting to a 900mm bench height.
For lower bench tops adjust the height of the legs to 180mm so the hob is located 10mm above the horizontal
combustible surface, ref. AS/NZS 5601.
Support Legs
Important
• Before leaving instruct the owner in the use of the cooker it should be expressly noted that we cannot accept any
liability for direct or indirect damage caused by wrong connection or improper installation. When being repaired,
the appliance must always be disconnected from the mains supply; if required, notify our customer service.

Baumatic BAF90EG 900mm Upright Oven User Manual 11
• Legs should be installed with the appliance close to its final destination,
as the legs are not designed for excessive force and will snap off if
too much side force is exerted on them (dragging along or angled
too much). When fitting, try to keep the appliance as close to a
horizontal position as possible. Use of a pallet jack is recommended.
If the legs are not used and the cooker is mounted onto a plinth, four
transit supports allow for clearance.
• With the legs fitted, the splash-back can be fitted.
• Follow the instructions shown in Fig. 07
Anti-tilt Device
• A chain should be fitted by the installer within 50mm of the hose connection point to prevent strain on the hose when
the cooker is pulled forward. The chain should restrict the appliance movement to no more than 80% of the hose
length. After the chain is installed, check that there is no strain on the hose or gas connections when the cooker is
pulled as far forward as the chain allows.
• The cooker is also supplied with two chains which are connected to the rear left and right of the appliance. The
chains should be connected to the wall directly behind the chains as low as possible to prevent the appliance from
tilting forward. If the appliance is installed between two cupboards, drill a hole on each side of the cupboards, pass
the chains through the holes and anchor the chains within each cupboard. Ensure the chain connections are strong
enough to support the weight of the appliance and taught to prevent it from tilting forward.
Anti-tilt Device
• WARNING: In order to prevent accidental tipping of the
appliance, for example a child climbing onto the open
oven door, the stabilising means must be installed.
Ensure the chains are correctly anchored to prevent the
appliance from tilting forward and to prevent strain on
the hose when the cooker is pulled forward.
• MAKE SURE THE ANTI-TILTING CHAINS ARE
TAUGHT WHEN ANCHORED TO PREVENT THE
APPLIANCE TILTING.

12 Baumatic BAF90EG 900mm Upright Oven User Manual
Conversation to different types of gas
• Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity network.
Replacing the nozzles to operate with another type of gas
• When converting to LPG remove the NG gas regulator (if fitted) and fit LPG test point adaptor.
• If converting to Natural Gas, fit gas regulator
• Follow the instructions below to change the burner nozzles on the work surface:
1) Pull out the plug from the electric outlet to avoid any type of electric contact.
2) Remove the grids from the work surface (Fig. 10).
3) Remove the burners (Fig. 10).
5) Burner "MINIMUM" adjustment:
Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:
• Light the burner and set the knob to the MINIMUM position (small flame).
• Remove the knob of the valve that is press fit on the rod of that valve.
• For all burners except for the wok burner, insert a small slotted screwdriver into the hole on the valve rod
(Fig. 12) and turn the choke screw to the right or left until the burner flame is adjusted to minimum.
• The wok burner has 2 adjustment screws on either side of the body of the valve (Fig. 13). Screw A is for the
outer ring and screw B is for the inner ring. Turn the choke screw to the right or left until the burner flam e is
adjusted to minimum.
• Ensure sure that the flame does not go out when s witching quickly from the MAXIMUM to the MINIMUM
position.
Oven burner adjustment: follow the instructions below to adjust the minimum:
• Light the burner setting the knob to the MAXIMUM position.
• Close the oven door and operate the oven for at least 10 minutes.
• Set the knob to the MINIMUM position (corresponding to 120°) and then remove it.
4) Unscrew the nozzles using a 7 mm spanner, and replace them (Fig.11) with those needed for the new type of
gas according to what is indicated in the Energy Consumption Table.
Conversation to Different Types of Gas

Baumatic BAF90EG 900mm Upright Oven User Manual 13
• With a slotted screwdriver turn the choking screw (see figure 14) and, while observing the flame at the same time
through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from
the MINIMUM to the MAXIMUM position.
• WARNING: The above-mentioned adjustment should be made only with natural gas burners, while for
those operating with liquid gas the screw must be locked at the end in a clockwise direction.
Appliance Electrical Connection
The electric connection must comply with the current legal standards and regulations.
Before making the connection, check that:
• The system electrical rating and the current outlet are adequate for the maximum power output of the appliance
(see the label applied to the bottom of the casing).
• The outlet or the system is equipped with an efficient ground connection in accordance with the current legal
standards and regulations. The manufacturer will not be responsible for the non-compliance with these instructions.
• The power cord is supplied with a 15A plug, suitable for the load indicated on the label and a standard 15A GPO.
• The power cord must be positioned so that a temperature of 75°C will not be reached at any point.
• Do not use reductions, adapters or splitters since they might cause false contacts and lead to dangerous overheating.
When the connection is made directly to the electric network:
• Use a device that ensures disconnection from the mains in which the contacts are opened to a distance that permits
complete disconnection according to the conditions for over-voltage category III.
• The ground wire must not be interrupted by the circuit-breaker.
• As an alternative, the electric connection can also be protected by a high-sensitivity residual current circuit- breaker
but this may be subject to nuisance tripping due to residual humidity in heating elements.
• It is highly recommended to attach the special green-yellow ground wire to an efficient ground system.
WARNING: If the power cord is replaced, the ground wire (yellow-green) connected to the terminal, should
be longer than the other wires by about 2 cm.
WARNING: if the supply cord is damaged, it must be replaced by the manufacturer or its service agent or
similarly qualified person in order to avoid a hazard.
Appliance Electrical Connection

14 Baumatic BAF90EG 900mm Upright Oven User Manual
The appliance conforms to the regulation AS4551 regarding gas appliance for domestic use and AS/NZS60335.26
regarding safety and CSPR 14 regarding electromagnetic compatibility.
Appliance Use and Maintenance
ATTENTION: Important Warnings.
• For cookers resting on base
ATTENTION: if the cooker rest on a base, take the measures necessary to prevent the cooker from sliding along the
support base.
• For cookers with electric ovens
ATTENTION: The unit becomes hot during use. Do not touch the heating elements inside the oven.
ATTENTION: The accessible parts can become hot during use. Keep children away from the appliance.
• For glass doors
ATTENTION: Do not use harsh abrasive cleaning products or metal spatulas with sharp edges to clean the oven
door’s glass since this could scratch the surface and the glass could break.
• For gas cooktops
ATTENTION: Clean burner tops and trivets at least once a week, or after any spillage. Gas inlet pipes should be
checked periodically for leakages (see section on leak testing), at intervals not exceeding 12 months. Lubrication of
valves should only be performed by an authorised person, and is required if the gas control knobs become stiff and
difficult to turn.
Do not use steam cleaner to clean the appliance.
WARNING: DO NOT MODIFY THIS APPLIANCE Please maintain your appliance regularly.
Replacing Parts
• Before performing any maintenance operations, disconnect the appliance from the gas supply and electricity network.
• To replace parts such as knobs and burners, just remove them from the seats without dis assembling any part of
the cooker.
• To replace parts such as nozzle supports, valves and electric components follow the procedure described in the
burner adjustment paragraph. To replace the valve or the gas thermostat, it is also necessary to disassemble the two
rear gas train brackets, loosening the 4 screws (2 per bracket) that attach it to the rest of the cooker and, unscrew
the nuts that attach the front burner valves to the control support, after removing all the knobs. To replace the gas or
electric thermostat, also disassemble the rear cooker guard, loosening the relative screws, to be able to pull down
and reposition the thermostat bulb.

Baumatic BAF90EG 900mm Upright Oven User Manual 15
Appliance Use and Maintenance
• To replace the oven bulb, just unscrew the protection cap that projects out inside the oven (Fig.16)
WARNING: Before replacing the bulb, disconnect the appliance from the electric power supply.
WARNING: The power cord supplied with the appliance is connected to the appliance with an X type connection (in
compliance with standards AS/NZS 60335-1, AS/NZS 60335-2-6 and subsequent amendments) for which it can be
installed without the use of special tools, with the same type of cord as the one installed.
• If the power cord becomes worn or damaged, replace it based on the information reported in table 2. To replace
the power cable, lift the terminal board’s cover and replace the cable.
CONTROL PANEL DESCRIPTION
• On the control panel, small symbols show the function of each knob or key. Here are the several controls that a
cooker can have:
Indicates which burner on the gas cooktop a control knob controls, a full square identifying the particular burner.
Indicates the control knob adjusts the functions of the electric oven.
shows the electric thermostat for electric fan oven.
shows the oven fan working button as to allow the oven to operates with fan assisted gas. The fan operation of
the oven prevents the operation of the grill, which therefore cannot be used with the fan in action.
Indicates the control knob adjusts the mechanical timer
shows the ignition key for the oven light (all except the electric fan oven)
shows the push-button for burner ignition
shows if keys are in position “on” or “off”
WARNING: If the power is cut off, the cook top burners can be lit with matches. When cooking foods with oil and fat,
which are very flammable, the user should not leave the appliance unattended. Do not use sprays near the appliance
when it is being used. When using the burners, make sure that the handles of the pots are correctly positioned. Keep
children away from the appliance.
Oven racks and trays
• The oven is supplied with a baking tray (with removable wire rack) and wire racks.
• Internally there is a wire support on either side with 5 mounting positions. The racks and tray are designed with a
small stop at the back. To insert, push the rack into one of the mounting positions angled down at the front so the
stop passes over the front of the support, and then push fully in. To remove, pull the rack out until the stop catches
at the front of the support & angle down to fully remove.

16 Baumatic BAF90EG 900mm Upright Oven User Manual
Using burners on cooktop
• A diagram is etched on the control panel above each knob which indicates which burner corresponds to that
knob. Each control knob controls a gas valve and built-in flame safety device.
• Manual lighting (it is always possible even when the power is cut off): Turn the control knob that corresponds to
the burner selected anticlockwise, setting it to the MAXIMUM position at the etched star (large flame on the control
knob (Fig. 18) and hold a lit match to the burner. Press the knob down and hold for 2 seconds after the burner
ignites so the thermocouple heats up. Release the control knob and adjust to the correct setting.
• Electric ignition: Turn the knob that corresponds to the burner selected anticlockwise, setting it to the MAXIMUM
position (large flame on the control knob (Fig. 18). Keep pressing the knob down at this position until the burner
ignites, and then wait 2 seconds for the thermocouple to heat up. Release the control knob and adjust to the
correct setting.
Appliance Use and Maintenance
Use of the dual burner (Fig19)
• This model controls both the central and external crown of the burner with just one valve.
• To ignite the central crown press and turn the knob to the maximum delivery position 1 and hold it down until
ignition: in this position the internal flame are at maximum.
• Turn the knob to position 2 to have the internal crown at the minimum.
• Turn the knob to position 3 to have the internal crown ant the external crown at the maximum.
• Turn the knob to position 4 to have the internal crown ant the external crown at the minimum.
Note: It is recommended not to try to ignite a burner if the relative flame cap is not in the correct position.
Tips for using burners correctly:
• Use suitably sized pots for each burner (see tab. 4 and Fig. 20).
Using the oven thermostat control knob
• The thermostat is used to set the maximum internal temperature of the oven. Turn the thermostat control knob
clockwise and align the selected temperature indicated on the knob with the index etched on the control panel
above it. Thermostat operation is indicated by an orange light which will turn off when the temperature inside
the oven is 10°C greater than the temperature setting, and will turn on when the oven is 10°C less than the
temperature setting. The thermostat can control the oven elements only if an oven function has been set. For
electronic timers, the timer must be off (“A” symbol off) or running.

Baumatic BAF90EG 900mm Upright Oven User Manual 17
There are 9 function as per below :
Quick Start/Defrost Function: This function runs the rear fans and all elements. The heat generated
is too hot to cook in, but is perfect for preheating the oven (run at the required temperature until the thermostat
light turns off and on a couple of time, then adjusts to the required function setting. To use as a defrost
function, leave the thermostat on 0. This allows air to flow over frozen food speeding up defrost times.
Conventional Cooking Function: This function runs the upper and lower elements. It is
dependent on the timer and the thermostat setting.
Lower Element Cooking Function: This function runs the lower element. It is dependent on
the timer and the thermostat setting. It can be used at low temperatures, for slow cooking casseroles &
custard, and at high temperatures for pastries.
Upper Element Cooking Function: This function runs the upper element. It is dependent on
the timer and the thermostat setting. With less power than the grill, this can be used to brown cauliflower
cheese and to reheat lasagne.
Grill Cooking Function: This function runs the upper and grill elements. It is dependent on the
timer and the thermostat setting. Best used for shorter grilling times, like toast or crumpets.
Grill & Fan Cooking Function: This function runs the upper and grills elements, and runs
both rear internal fans. It is dependent on the timer and the thermostat setting. Best used for longer grilling
times, or when grilling foods with a lot of moisture.
Fan Assist Cooking Function: This function runs the upper and lower elements, and runs both
rear internal fans. It is dependent on the timer and the thermostat setting. Best used when cooking large
amounts of food at one time, for frozen potato products and crumbed/battered chicken or fish.
Fan Oven Cooking Function: This function runs the circular rear elements; and runs both rear
internal fans. It is dependent on the timer and the thermostat setting. This function is suitable to most types of
cooking, with even temperatures throughout the oven.
Pizza Cooking Function: This function runs the lower and circular rear elements, and runs both
rear internal fans. It is dependent on the timer and the thermostat setting. Great for Pizzas, pastries or flat
breads, where you want the base crispy and the rest cooked.
Using Oven Functions
Using the oven function control knob (Fig. 22)
• The oven function knob is used to control the electric fan and the oven
elements in set combinations in conjunction with the timer and thermostat.
• The electric oven is heated by 4 elements:
a) Upper element (1200W) and grill element (1500W) combined
at the top of the oven cavity.
b) Lower element (1600W) at the bottom of the oven cavity.
c) Two circular elements (1200W) at the rear of the oven cavity,
situated around the 2 internal fans.
• Select an oven function by turning the oven function control knob so that
the symbol for the required function is at the top and in line with the index etched on the control panel above it.
• Note: The timer and thermostat must be set correctly for the oven to function.
• To turn electric oven off adjust the oven function control knob to position
• 0 (no function selected). Setting the thermostat control knob to position 0 turns off the elements but it is still
possible, using the oven function knob ,to turn on the electric fan and the oven light.

18 Baumatic BAF90EG 900mm Upright Oven User Manual
Using the electric oven
• When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of
about 250°C to eliminate any odours generated by the internal insulation. During normal oven use, select the
desired cooking temperature using the thermostat knob and wait until the orange light turns off (set temperature
has been reached) before putting in any food. The oven is equipped with 5 guides at different heights (Fig. 23)
which can be used to insert shelves or the tray. To keep the oven as clean as possible it is recommended to cook
meat on the tray or on the shelf that has been inserted inside the tray. Always turn the oven off by adjusting the
oven function control knob to off (0).
NOTE: After use, the cooling fan will continue to run until the internal electrical system has cooled
sufficiently.
Cooking Functions
• When cooking, always open the oven door slightly first (head away from the door), to allow any built-up steam to
escape, and then open fully. Always use heat resistant gloves when removing hot items from the oven. Never line
the sides or base of the oven, or enamel backing dishes with aluminium foil (it can damage the enamel surface).
Never cook or place cookware on the base – always use trays and shelves provided.
• Always preheat your oven before cooking (see the quick start function), which allows more accurate timing of
cooking.
conventional cooking
• Conventional cooking cooks with heat coming from both the top and bottom, ideal for roasts and pastries. After
preheating oven to the correct temperature (50°C to 250°C), adjust oven function control knob to conventional
cooking and place food inside oven. Set timer if needed.
fan oven cooking
• Fan Oven cooking cooks with heat coming from the rear of the oven, with hot air circulated around by the fans,
ideal for cooking different types of food together without mixing the tastes. Pre-heat the oven for 10 minutes before
inserting the trays. Adjust oven function control knob to fan oven cooking and place food inside oven. Set timer if
needed.
grilling
• The grill is controlled using the oven’s temperature knob. The grill function uses both elements at the top of the
oven, so is faster and more powerful than using the top element alone. Run this function with the door closed and
at a temperature not exceeding 150°C for up to 15 minutes. Use the enamel tray with wire rack insert at positions
1 or 2 (or lower to slow down the grilling process). Do not leave the tray in the upper positions when not in use, as
they will deflect heat away from food.
• Preheat for 5 minutes first before adding the food and tray. This function is best for thinner, quickly cooked food
like toast; for thicker food that will take longer, use the grill and fan cooking function.
grilling with fans
• This function is similar to the grilling function, but with the rear fans added, allowing a more even heat to flow
around the food. Run this function with the door closed. Place the food on a wire rack and insert at position 3.
Place a baking dish on level 5 to catch any juice or crumbs (this allows the heat to circulate the food). This is better
for thicker foods which need to be cooked for longer times. Preheat for 5 minutes first before adding the food and
tray.

Baumatic BAF90EG 900mm Upright Oven User Manual 19
Using the Minute-Minder (fig.24)
• The minute-minder advises the user, with an acoustic signal, when food has been
cooked, after a certain time period has elapsed. To use the device, wind the minute-
minder by turning the knob clockwise one complete turn. Then turn the knob
counterclockwise so that the indicator corresponds with the selected cooking time
• WARNING: the acoustic signal does not stop the cooking cycle. The use must turn
off the cooking cycle by hand using the relative knobs.
Using the end of Cooking Timer (fig 25)
• It allows to select the cooking time manually or timer with automatic shut off of the
oven at the end of cooking.
• If not cooking time is selected, it is necessary to position the timer knob on the
symbol .
• To turn off the oven, select the timer knob on the desired cooking time and set the
function and the temperature knobs; the end of the countdown will be confirmed
with a repeating tone.
NOTE: This function is available for the electric oven only.
Cooking Functions
Using the Digital Clock (fig.26)
Power on
• Display is flashing
Time of day function
• 3 button version: press time of day button
• 2 button version: press both button simultaneous
• Set time of day with "+" and "-" buttons.
• This function remains activated 7 seconds after the last "+" / "-" operation!
Change Summertime / Wintertime
• Activate time of day function; press the button for 4 seconds until the hours display will flash.
• Change the hours only by using the “+” or “-“ button. The minutes and hidden seconds will not be affected !
Set timer
• This function will be activated with "+" button. Press "+" button again to increase duration time.
• During setting the units are 10 seconds steps or minutes.
• During count down the timer has priority in the display. The bell- symbol illuminated. The units are seconds or
minutes in the long time section. The maximum time is 10 h. The format change will happen after 99 minutes and
50 seconds to 1 hour and 40 minutes.
• The pot- symbol illuminated.
• To show time of day press “time of day” button for 6 seconds.
Reset timer
• Count down to zero with permanent pressing “ – “ button. (automatic stop at zero )

20 Baumatic BAF90EG 900mm Upright Oven User Manual
Cooking Functions
Signal
• The signal after “time out” will stay 7 minutes if it has not been reset with “time of day” button.
• The following signal will be skipped if time of day is pressed during the last 15 seconds of the timer.
Signal frequency
• If no function is activated, the signal frequency can be selected by pressing the "-" button.
• Three different frequencies (1,5 ; 2,0 ; 3,0kHz) are selectable.
Using the Touch Clock (fig.27)
Mains frequency detection
• At power on mains frequency is determined. When the timer is
connected to 60Hz, the Celsius symbol is flashing during start-up.
Power On
• At power on, the relay contact is opened. The display and AUTO symbol
flashes and time of day starts from 0:00. Power on state with flashing daytime remains until time of day is set.
Setting Time of Day
• Press PLUS and MINUS button simultaneously. At Power On, also MODE button is possible.
• Time of day can be set with PLUS or MINUS, while the colon between hours and minutes is flashing.
• Quick setting mode starts when PLUS or MINUS is held for more than 1 second. If daytime setting mode is
selected while an automatic program is active, the automatic program is cancelled.
The Buzzer
• The buzzer interval alarm signal sounds if minute minder has reached the end time. The signal can be switched off
by pressing any key or by passing the signal duration limit.
Changing the Buzzer frequency
• First press Plus and Minus simultaneously (menu far editing the time) and then Mode for selecting the menu far
changing the buzzer frequency. While the text is visible the buzzer signal frequency can be changed by touching
Minus repetitively.
• Note: If the touch pad is inactive, a visual alarm will only be reset when a valid key combination is pressed far more
than 2 seconds.
Clearing Programs and Manual function
• The duration of the minute minder can be cleared by
• a) "clear Function": First select minute minder program, then press PLUS and MINUS button simultaneously.
• after this clear the display returns from adjustment mode to time of day immediately.
• b) Back counting of duration to zero. The timer remains in adjustment mode.
Minute Minder
• While minute minder mode is selected, the Bell symbol flashes and the display reads the remaining time in hours
and minutes, only if the last minute is counting down the remaining seconds are displayed. An active minute
minder program is indicated by the statically illuminated Bell symbol. If alarm time has finished, an acoustic interval
signal sounds and the Bell symbol flashes.
• The minute minder program runs independently of other programs.
Key Lock
• After power on reset or when no key is pressed for 7 seconds, the key look function is activated. Pressing a valid
key or key combination for 2 seconds or more will deactivate the key lock.