BDI COSMO 5720 User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a
BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Cosmo Bar is designed for indoor use on level floors.
Clean wood, metal, and porcelain surfaces with a damp cloth.
Cosmo is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of this
product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Cosmo & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2019, BDI
Made in China. 12.05.2019 V3
COSMO™5720
BAR
Tool Required:
Slotted Screwdriver
A1 Cabinet x 1
A2 Lower Shelf x 1
C6 Middle Drawer
Liner x 1
C7 Side Drawer
Liner x 2
C5 Anti-skid Pad x 2
T1 Hex Driver x 1
H1 M6 x 12mm Screw
x 26
C3 Bottom Connector
Tube x 2
H5 Micro HDMI/USB
charge cord x 1
C2 Top Connector Tube x 2
C1 Base Frame x 2
T2 Leveler Wrench x 1
H3 Wall Anchor
Strap x 2
H4 Rechargeable
Strip Light

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
2
Step 2 - Base Assembly
Position base frame C1 on the floor with tabs facing up. Slide both top connector tubes C2 onto the 2
large U shaped tabs of base frame C1 making sure the holes are facing inside. Slide both bottom con-
nector tubes C2 onto the 2 small U shaped tabs of base frame with holes facing down. Attach connec-
tor tubes using 8 screws H1. Sleeve the other base frame C1 over the assembly as shown below and
tighten all 16 screws H1 with hex wrench T1.
C2
C2
C3
C3
H1
T1 H1 x 16
C1
C1
H1
H1
H1
H1
H1
H1
H1

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
3
2 Person Ta sk
Step 3 - Base Attachment
With help from another person, carefully position the cabinet A1 onto at least two layers of packing
material and orient on its back as shown. Note: the packing material creates finger space to lift the
cabinet after attaching the base. Position the base as shown and attach with 4 screws H1 and tighten
with hex wrench T1.
2 layers of honeycomb
packing material
T1 H1 x 4
H1
H1 H1
H1
A1 Cabinet x 1

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
4
2 Person Ta sk
2
1
C5 Anti-skid pad x 2
2
Step 4 - Standing the Unit
Position the anti-skid pads C5 under the back legs as indicated with arrow #1 making sure that the
pads are centered on the end of the legs. With 2 people (1 person on each side) carefully and slowly
lift the cabinet with hands placed along the edges of the cabinet indicated with arrow #2.
1
Recommended hand
positions (both sides)
Leg centered on Anti-skid pad
Lift
C5

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
5
Step 5 - Wall Preparation
CAUTION! DO NOT allow children to swing on the open doors.
It is strongly recommended that you anchor your Cosmo Bar cabinet to the wall using two anchor
straps H3 included. Determine the desired location of your Cosmo Bar and then position the bar 24" in
front of the wall. Mark the wall and insert 2 wall inserts (not included) in the position indicated below.
71cm71cm
28"28"
61cm61cm
24"24"
175cm175cm
69"69"
wall anchors
(not included)
H3 Anchor
Strap x 2

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
6
Step 6 - Wall Attachment
Attach 1 end of the anchor straps to the wall. Carefully move your Cosmo bar close to the wall and
attach the loose end of the anchor straps to the top of the cabinet using screws H1 going into the
threaded inserts as shown. Tighten with hex wrench T1.
Step 7 - Lower Shelf Installation
Tilt the lower shelf as shown, insert the shelf into the front opening of the base and rotate carefully down
onto the lower cross bars of the frame. Attach the lower shelf with 4 screws H1 and tighten with hex
wrench T1.
T1
H1 x 2
H1 x 4
T1
H1 x 4
1 2 3
H3 Anchor
Strap
H1

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
7
Step 8 - Light Installation
Find the rechargeable strip light H4. Using the Micro HDMI/USB charge cord H5, charge the light for
6 hours. Once charged, install it onto the metal strip (it is held with magnets) located in the angled recess
towards the top front of the cabinet. Make sure the proximity sensors are facing forward and the light
switch is turned on. The light is designed to turn off automatically when the cabinet doors are closed.
Step 9 - Drawer Liner Installation / Magnetic Door Catch
Open the push-open drawer and install middle drawer liner C6 and both side drawer liners C7.
Using a slotted screwdriver, unscrew the magnetic door catches a few turns until they make contact
with and hold the doors shut.
H4 Rechargeable
Strip Light
C6
C7
C7
Proximity Sensors
On/Off
Micro HDMI / USB
charge cord H5

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
8
Reposition Shelf Pins
(if needed)
Wine Glass
Storage
Wine Bottle
Storage
Step 10 - Shelf Adjustment
Adjust the height of the adjustable shelf if needed by moving the positions of the shelf pins.
Adjustable Shelf
Mirror
Porcelain
Surface
Bottles and cans

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
9
Step 11 - Leveling and Adjusting the Door Gaps
With both doors closed, check to see if the top corners of the doors align. If not, dial out the correspond-
ing front leveler under the door that is sagging.
Example:
If the door on the right is low, dial out the right front leveler to raise the door back into alignment with the
left door.
To move the right door up, dial
the front, right leveler out.
To move the left door up, dial the
left, front leveler out.
Dial out
Note: To hold the doors in an open position, partially extend the
two (2) front levelers. This action will tilt the cabinet back slightly,
preventing the open doors from swinging towards their closed
position.

bdiusa.com
customerservic[email protected]om
COSMO 5720
BAR
10
Cleaning
If a spill occurs, the porcelain surface on your Cosmo Bar may be removed for cleaning. To remove, open
the drawer about 8", reach inside and find the 60mm disc just under the front center edge of the porcelain.
Rotate the disc 180 degrees. Lift the porcelain out by pushing up from below.
DiscPorcelain surface
Rotate Disc to Unlock Unlocked Position