BDI FLO 7279 User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a
BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Flo Media Console is designed for indoor use on level floors.
Clean painted surfaces and steel parts with a damp cloth.
Flo is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of this
product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by BDI Studio.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Flo & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2018, BDI
Patent: www.bdiusa.com/ip
Made in China. 06.14.2018 V1
FLO™7279
MEDIA CONSOLE
Tool Required:
Phillips screwdriver
A1 Cabinet x 1
C3 Back Panel x 2
C2 Side Shelf x 2
C1 Center Shelf x 1
A2 Base Rails x 2
A3 Leg x 2
T1 Hex Wrench x 1
H1 1/4-20 x 12 mm
Screw x 8
H2 M4 x 25 mm
Screw x 8
H3 1/4-20 x 75 mm
Flat head Screw x 8
H4 Door Pull x 4
H5 Cord Wrap x 2

bdiusa.com
customerservic[email protected]om
FLO 7279
MEDIA CONSOLE
2
Step 2 - Assemble the base
Position the 2 base rails on a padded floor with the end plates facing as shown and countersunk holes facing
up. Attach the 2Legs A3 to 2 Base Rails A2 with 8Flathead Screws H1 using Hex wrench T1. Make sure
the countersunk holes on the legs are positioned on the outside.
Step 3 Attach the base
With help from another person, carefully position the cabinet on its back. Attach the base using 8 screws H3
going through the countersunk holes on the base rails and into the threaded holes on the bottom of the cabinet.
A2
2 Person Task
T1
A3
A3
H1 x 8
A2
H3 x 8 T1
Countersunk holes
face up.
Arrow faces up.

bdiusa.com
customerservic[email protected]om
FLO 7279
MEDIA CONSOLE
3
Step 4 Stand Up / Attach Door Pulls / Adjust shelves
With help from another person, carefully position the cabinet onto its base. Open the doors and attach the 4
door pulls H4 using 8 screws H2 and a Phillip's screw driver. The shelves in your Flo Media Console are
adjustable. Shelf pins may be unscrewed and moved up or down.
STEP 5 - Level your unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg. If your floor
is uneven, you may extend one or more levelers to attain a level, stable cabinet placement. Turning the leveler
clockwise will extend the leveler; turning it counter-clockwise will retract it.
2 Person Task
C2
C1
C2
down
H2 x 8

bdiusa.com
customerservic[email protected]om
FLO 7279
MEDIA CONSOLE
4
Step 6 Insert Back Panels / Manage Cables
The 2 Back Panels C3 are removable and can slide towards the middle. To remove lift up and pull the bottom
edge out of its groove. To re-install, put the top edge of the back panel into the top groove, then drop the bot-
tom edge into the bottom groove.
Your Flo Media Console comes with 2KLEET Cord Wraps H5 pre-installed on the back. The cord wraps can
also be installed on the bottom of the cabinet behind the back base rail. Remove the adhesive backing and
adhere the Cord Wraps where ever desired.
1
2
C3
C3
H5 Cord Wrap Optional Position

bdiusa.com
customerservic[email protected]om
FLO 7279
MEDIA CONSOLE
5
STEP 7 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame. If the cabinet’s doors appear out of alignment, this condition can be corrected with minor
adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can
modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet.
Example:
Tightening screw 1
on top hinge will move the
top of the door in the
direction shown
Example:
Adjusting screw 2
on both hinges (same direction)
will move the door up or down
Use the Phillips Screwdriver T1 supplied to adjust the door hinges:
• By adjusting Screw 1, the door will move LEFT or RIGHT within the
frame. Make minor adjustments at both top and bottom hinges for
best results.
• By adjusting Screw 2, the door will move UP or DOWN. For best
results, adjust Screw 2 on both the top and bottom hinges.
• By adjusting Screw 3 the entire door will move IN or OUT, opening
or closing the gap between the door frame and cabinet. (This screw
rarely needs adjustment.)
123