BDI Novia 8421 User manual

Novia®8421
Assembly Instructions
4/2008

2
Your Novia® Home Theater Furniture is engineered for easy
assembly. Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Novia™ Home Theater Furniture is designed for indoor use on level
floors. Clean glass with glass cleaner. Clean glass with glass cleaner,
and steel parts and wood veneer with a moist cloth.
Step 1
Unpack and identify the parts listed above.
The assembly workspace should be a non-marring surface such as
carpet. For missing hardware pieces, please contact BDI Customer
Service at: customerser[email protected]
All other concerns please contact your local BDI Retailer.
Step 2
Install Glass Panel (H) on top of Assembled Cabinet (I).
www.bdiusa.com
customerser[email protected]
G - Back Panel x 1
For more information about the adjustable levelers
and troubleshooting assembly, be sure to check out
“Fine tuning your new BDI Novia Home Theater
Furniture” at the end of these instructions.
H
I
D - Knob Screw x 3
E - Knob x 3
F - Adjustable Shelf x 1
C - Leveler Wrench x 1
A - Allen Wrench x 1
B - Phillips Screwdriver
x 1
H - Glass Panel x 1
I - Assembled Cabinet x 1

3
Step 3
Install Knob (E) to the front side of door and drawer faces using Knob Screw (D) and Phillips
Screwdriver (B).
The shelf pins located inside the left and right cabinet space may be repositioned, allowing you to raise
or lower the shelf to the desired level.
Step 4
Install Back Panel (G) to the rear side of cabinet. Velcro straps are included as wire management for
your convenience.
1.
2.
E
D
B

4
Option A
The flip-down door compartment may be used to house a center channel speaker
(up to 37.5” width x 10.5” depth x 8” height).
Option B
In conjunction with a center channel speaker, or component (up to 19.25” width x 15.5” depth x 8”
height), this area may be used to store DVD’s, VHS cassettes, and CD’s. In order to do this, remove
center wood strip.

5
Optional glass panel insert is available. Contact BDI
Customer Service at: customerser[email protected]
Option C
Side compartment may be used to accommo-
date a vertical standing video game unit. To
do this, first remove the wood strip and then
adjustable shelf.

6
Step 5
Leveling
There are adjustable levelers on the bottom of the cabinet, which may be adjusted depending on your
leveling situation.
Two of the four leveler glides are accessible near the bottom of the side
panels using the Leveler Wrench (C).
The other two adjustable leveler glides are located in the rear center of the
bottom shelf. Use Allen Wrench (A) to adjust.
C
A
Turn clockwise to raise cabinet.
Turn counter clockwise to lower cabinet.

7
Fine-tuning your Novia Home Theater Cabinet
Your Novia home theater cabinet is engineered to allow a range of adjustments. Please read and retain this guide
so that you can fully enjoy the look and use of your BDI cabinet for years to come.
Due to uneven floors or perhaps gentle jostling during shipment, your BDI cabinet may not appear to be in perfect
alignment when first assembled or when loaded with heavier electronic equipment. Such alignment issues are usually
eliminated with only a few minor adjustments.
However, unless manual leveling is required, or you wish to prevent the cabinet from rolling, many users choose
to keep the cabinet’s levelers up and off the floor. This allows easier cabinet movement for greater access to rear
panels and wire-management, and permits easier cleaning/vacuuming underneath the cabinet.
By following the simple steps in this guide, you can be sure that your BDI cabinet is in optimum tune. If you need
additional assistance, contact BDI at customerser[email protected].
STEP 1 - Level your cabinet (if needed)
After unpacking and assembling your Novia cabinet, inspect it to be sure that it is resting level on the floor, that all
doors appear level, and that they open and close freely without rubbing or binding.
Properly adjustment of the cabinet’s levelers quickly corrects most panel-alignment issues. There are four (4)
adjustable levelers on the bottom of the cabinet; each may be individually adjusted depending on your leveling
scenario.
Two (2) of the levelers are accessible near the bottom of the side panels,
near front and back, using the provided Leveler Wrench (C).
Two (2) of the levelers are accessible from inside the cabinet---at the
bottom panel, inside the center compartment---and are adjustable using
the provided Allen Wrench (A).
STEP 2 - Adjust Doors
If the cabinet’s doors appear out of alignment, this condition can be
corrected with minor adjustment to the European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other
elements. Depending on your scenario, patience as well as some
trial and error may be called for. With a few adjustments, you can
modify the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Adjustments may be made to Novia’s door hinges with the use of the Phillips head screwdriver.
Each hinge assembly has three (3) adjustment screws:
By adjusting Screw 1, the door will move left and right within the frame. Make minor adjustments at both top
•
and bottom hinges for best results.
By adjusting Screw 2, the door will move up and down within the frame (the top and bottom hinges must be•
adjusted the same amount).
By adjusting Screw 3 will cause the entire door to move in and out, opening and closing the gap between•
the door frame and cabinet. This screw rarely needs adjustment.
INCORRECT! Door
is out of alignment
with the rest of the
unit.
CORRECT! Door is
sitting squarely and
evenly spaced on
tops and sides.

8
1
2
2
1
Novia®8421
Designed by BDI Design Studio.
These distinctive product configurations are protected by US
and international patents, trade dress, and/or copyright laws.
“Novia” and BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2008, BDI
4/2008
Fine-tuning your Novia Home Theater Cabinet
(continue)
Some BDI cabinets feature a ‘flip-down’ door with two round hinge
assemblies and an articulating arm assembly. (Refer to
the image.) By fine-tuning at each hinge location, you can noticeably
adjust the overall door position.
Screw 1 adjusts the door position INward and OUTward.
The smaller screw, Screw 2, adjusts the door UP and DOWN.